- Introduction to Siemens SIPROTEC 4 7SJ Series
- 1. Siemens SIPROTEC 4 7SJ Relay Models
- 2. SIPROTEC 4 7SJ61 – Overcurrent and Earth Fault Protection
- 3. SIPROTEC 4 7SJ62 – Directional Overcurrent Protection
- 4. SIPROTEC 4 7SJ63 – Multifunction Protection with Local Operation
- 5. SIPROTEC 4 7SJ64 – Multifunction Protection with Synchronizing Function
- 6. SIPROTEC 4 7SJ66 – Multifunction Protection with Integrated Control
- 7. Comparison of SIPROTEC 4 7SJ61, 7SJ62, 7SJ63, 7SJ64 and 7SJ66
- 8. Protection Functions Commonly Used in the 7SJ Series
- 8.1 Phase Overcurrent Protection – ANSI 50/51
- 8.2 Earth Fault Protection – ANSI 50N/51N
- 8.3 Directional Overcurrent – ANSI 67
- 8.4 Directional Earth Fault – ANSI 67N
- 8.5 Negative Sequence Protection – ANSI 46
- 8.6 Thermal Overload Protection – ANSI 49
- 8.7 Undervoltage Protection – ANSI 27
- 8.8 Overvoltage Protection – ANSI 59
- 8.9 Frequency Protection – ANSI 81
- 8.10 Circuit Breaker Failure – ANSI 50BF
- 8.11 Automatic Reclosing – ANSI 79
- 8.12 Synchronism Check – ANSI 25
- 9. DIGSI 4 – Configuration and Parameterization of SIPROTEC 4 7SJ Relays
- 10. IEC 61850 and Communication in SIPROTEC 4 7SJ Relays
- 11. Testing and Commissioning of SIPROTEC 4 7SJ Relays
- 12. Disturbance Recording and Fault Analysis
- 13. Common Troubleshooting Problems
- 14. Advantages of SIPROTEC 4 7SJ Protection Relays
- 15. SIPROTEC 4 7SJ Series Training by Elec-Engg
- 16. Conclusion
Introduction to Siemens SIPROTEC 4 7SJ Series
The Siemens SIPROTEC 4 7SJ series is a family of numerical multifunction protection relays designed primarily for feeder, line, motor and distribution system protection.
These relays are widely used in medium-voltage substations, industrial power systems, utility distribution networks and electrical installations.
The SIPROTEC 4 7SJ family combines several important functions in one intelligent electronic device (IED), including:
- Phase overcurrent protection.
- Earth fault protection.
- Directional overcurrent protection.
- Negative sequence protection.
- Thermal overload protection.
- Voltage and frequency protection.
- Circuit breaker failure protection.
- Automatic reclosing, where supported.
- Measurement and monitoring.
- Event and disturbance recording.
- Communication and substation automation.
One of the main advantages of the 7SJ series is its flexibility. Depending on the relay model, hardware configuration and ordered functional scope, engineers can implement different protection and control schemes.
All these relays are engineered using Siemens DIGSI 4 software.
This guide covers the main SIPROTEC 4 7SJ models, their differences, protection functions, applications, parameterization, DIGSI 4 engineering, IEC 61850 communication, testing and commissioning.
1. Siemens SIPROTEC 4 7SJ Relay Models
The main SIPROTEC 4 7SJ multifunction protection models include:
| Relay model | Main application |
|---|---|
| 7SJ61 | Overcurrent and earth fault protection |
| 7SJ62 | Multifunction feeder protection |
| 7SJ63 | Multifunction protection with enhanced local operation |
| 7SJ64 | Multifunction protection with synchronizing functionality |
| 7SJ66 | Multifunction protection with integrated local control |
The models are designed for different hardware and application requirements.
An important distinction is that 7SJ80 and 7SJ81 belong to the SIPROTEC Compact family, while 7SJ82 belongs to SIPROTEC 5. They are not SIPROTEC 4 models and are therefore outside the main scope of this article. Selection Guide (US-Version)+2
2. SIPROTEC 4 7SJ61 – Overcurrent and Earth Fault Protection
The SIPROTEC 4 7SJ61 is a multifunction numerical protection relay designed primarily for feeder protection applications.
It is suitable for medium-voltage distribution networks and industrial electrical systems.
Main applications
- Medium-voltage feeder protection.
- Cable protection.
- Overcurrent backup protection.
- Transformer backup protection.
- Industrial distribution systems.
- Electrical equipment protection.
Main protection functions
Depending on the device configuration, available functions include:
| ANSI | Protection function |
|---|---|
| 50 | Instantaneous overcurrent |
| 51 | Time overcurrent |
| 50N | Instantaneous earth fault |
| 51N | Time-delayed earth fault |
| 46 | Negative sequence overcurrent |
| 49 | Thermal overload |
| 37 | Undercurrent |
| 27 | Undervoltage, where supported |
| 59 | Overvoltage, where supported |
| 81 | Frequency protection, where supported |
| 50BF | Circuit breaker failure, where supported |
The 7SJ61 is particularly useful in applications where phase current and earth fault protection are the primary requirements.
Important engineering considerations
When configuring a 7SJ61, engineers should pay particular attention to:
- CT ratio and secondary current selection.
- Phase overcurrent pickup.
- Earth fault pickup.
- IEC or ANSI time-current characteristics.
- Time multiplier settings.
- Binary input and output assignment.
- Trip circuit configuration.
- Protection coordination.
3. SIPROTEC 4 7SJ62 – Directional Overcurrent Protection
The SIPROTEC 4 7SJ62 is a multifunction numerical protection relay designed for feeder and distribution system protection.
Compared with the 7SJ61, the 7SJ62 provides additional voltage measurement capabilities in appropriate hardware configurations.
This makes it suitable for applications requiring directional protection and voltage-dependent functions.
Main applications
- Radial distribution feeders.
- Ring distribution networks.
- Industrial power distribution.
- Transformer feeder protection.
- Directional earth fault protection.
- Backup protection for transmission and distribution equipment.
Main protection functions
| ANSI | Protection function |
|---|---|
| 50/51 | Phase overcurrent |
| 50N/51N | Earth fault |
| 67 | Directional overcurrent |
| 67N | Directional earth fault |
| 46 | Negative sequence |
| 49 | Thermal overload |
| 27 | Undervoltage |
| 59 | Overvoltage |
| 81 | Frequency |
| 50BF | Circuit breaker failure |
| 79 | Automatic reclosing, where supported |
Directional overcurrent protection
One of the most important features of the 7SJ62 is directional overcurrent protection.
In networks with multiple sources or interconnected feeders, current magnitude alone may not be sufficient to determine the fault direction.
Directional protection uses current and voltage quantities to identify whether the fault is in the forward or reverse direction.
The basic operating principle involves:
- Measuring phase current.
- Measuring reference voltage.
- Determining the phase relationship between current and voltage.
- Calculating the directional operating quantity.
- Checking the directional characteristic.
- Permitting or blocking the overcurrent stage according to the selected direction.
Directional earth fault protection
Directional earth fault protection is important in networks where earth fault current can flow from multiple directions.
The relay evaluates residual current and the appropriate polarizing quantity, depending on the selected protection principle.
This is especially useful in:
- Ring networks.
- Parallel feeders.
- Networks with distributed generation.
- Resistance-earthed systems.
- Networks with multiple supply sources.
4. SIPROTEC 4 7SJ63 – Multifunction Protection with Local Operation
The SIPROTEC 4 7SJ63 is a multifunction protection device designed for feeder protection and applications requiring enhanced local operation and control.
Its hardware and operating concept provide facilities for monitoring and controlling associated switchgear, subject to the selected configuration.
Main applications
- Medium-voltage switchgear.
- Distribution feeder protection.
- Industrial substations.
- Feeder protection with local control.
- Electrical network monitoring.
Main features
- Numerical overcurrent protection.
- Earth fault protection.
- Directional protection where configured.
- Measurement and monitoring.
- Binary input and output processing.
- Local indication and operation.
- Circuit breaker control where configured.
- Event and fault recording.
Local control applications
The relay can be integrated into a feeder control arrangement involving:
- Circuit breaker.
- Disconnector.
- Earthing switch.
- Local/remote selection.
- Electrical and logical interlocking.
The exact control facilities depend on the hardware version and engineering configuration.
5. SIPROTEC 4 7SJ64 – Multifunction Protection with Synchronizing Function
The SIPROTEC 4 7SJ64 is a multifunction protection relay designed for feeder applications requiring additional synchronizing functionality.
It can be used in applications involving interconnected electrical networks, generators and bus couplers, depending on the system design.
Main applications
- Distribution feeder protection.
- Industrial substations.
- Feeder protection with synchronism checking.
- Switching between electrical sources.
- Bus coupler applications.
- Systems requiring controlled circuit breaker closing.
Synchronism Check – ANSI 25
Synchronism check is an important function when connecting two electrical systems.
Before closing a circuit breaker between two energized systems, the relay checks the relevant electrical quantities.
Typical supervision criteria include:
- Voltage difference.
- Frequency difference.
- Phase angle difference.
- Synchronism conditions.
- Circuit breaker closing time.
The purpose is to prevent unsafe closing when the two electrical systems are not sufficiently synchronized.
The synchronizing function must be configured according to the intended application and the relay’s available measuring inputs.
6. SIPROTEC 4 7SJ66 – Multifunction Protection with Integrated Control
The SIPROTEC 4 7SJ66 is a multifunction protection relay designed for applications combining protection, measurement, monitoring and local control.
It is particularly suitable for medium-voltage switchgear and feeder bays where more extensive local operating facilities are required.
Main applications
- Medium-voltage feeder protection.
- Industrial substations.
- Distribution switchgear.
- Feeder protection and bay control.
- Circuit breaker monitoring and control.
- Electrical network automation.
Main capabilities
- Phase overcurrent protection.
- Earth fault protection.
- Directional protection, where configured.
- Voltage and frequency functions, where supported.
- Thermal protection.
- Measurement and metering.
- Event and fault recording.
- Binary input and output processing.
- Local switchgear control.
- Communication with substation automation systems.
The 7SJ66 offers an enhanced local operating concept compared with simpler feeder protection configurations.
Its exact capabilities depend on the selected order variant and engineering settings.
7. Comparison of SIPROTEC 4 7SJ61, 7SJ62, 7SJ63, 7SJ64 and 7SJ66
The following table provides a practical comparison of the five main models.
| Feature | 7SJ61 | 7SJ62 | 7SJ63 | 7SJ64 | 7SJ66 |
|---|---|---|---|---|---|
| Phase overcurrent | Yes | Yes | Yes | Yes | Yes |
| Earth fault | Yes | Yes | Yes | Yes | Yes |
| Voltage measurement | Variant-dependent | Yes | Yes | Yes | Yes |
| Directional protection | Limited by hardware | Yes | Yes | Yes | Yes |
| Synchronism check | — | Variant-dependent | — | Yes | Variant-dependent |
| Local control | Basic | Available | Enhanced | Available | Enhanced |
| Feeder automation | Yes | Yes | Yes | Yes | Yes |
| DIGSI 4 | Yes | Yes | Yes | Yes | Yes |
Note: This is an application-level comparison, not a substitute for the Siemens function-selection matrix. Exact function availability, hardware inputs, outputs and communication options must be checked against the device order number and firmware.
8. Protection Functions Commonly Used in the 7SJ Series
The following sections explain the main protection functions used across the 7SJ family.
8.1 Phase Overcurrent Protection – ANSI 50/51
Overcurrent protection is the fundamental function of the 7SJ series.
The relay continuously measures the three-phase currents and compares them with configured thresholds.
Two principal stages are used:
High-set or instantaneous overcurrent
Operates when current exceeds a configured threshold, without an intentional inverse-time delay.
Time-delayed overcurrent
Operates according to a selected time-current characteristic.
Common IEC curves include:
- Standard Inverse.
- Very Inverse.
- Extremely Inverse.
- Long-Time Inverse.
The selection of the characteristic depends on network fault levels and coordination requirements.
8.2 Earth Fault Protection – ANSI 50N/51N
Earth fault protection detects current flowing through an unintended earth return path.
Residual current can be calculated as:
\[ 3I_0=I_A+I_B+I_C \]
The relay can use residual current measured through the phase CTs or a dedicated earth-current input, depending on the device arrangement.
8.3 Directional Overcurrent – ANSI 67
Directional overcurrent protection determines the direction of the fault using current and voltage information.
It is particularly important in interconnected and ring distribution networks.
8.4 Directional Earth Fault – ANSI 67N
This function identifies the direction of earth fault current and helps provide selective protection in networks with multiple sources.
8.5 Negative Sequence Protection – ANSI 46
Negative sequence protection detects unbalanced three-phase current conditions.
It is useful for protecting motors and other electrical equipment against abnormal unbalanced operation.
8.6 Thermal Overload Protection – ANSI 49
The thermal model estimates the heating condition of the protected equipment using current and configured thermal parameters.
It can be used to prevent excessive thermal loading.
8.7 Undervoltage Protection – ANSI 27
Undervoltage protection detects voltage levels below a configured threshold.
It can be used for alarms, load shedding and equipment protection.
8.8 Overvoltage Protection – ANSI 59
Overvoltage protection detects excessive voltage conditions and initiates an alarm or trip according to the protection scheme.
8.9 Frequency Protection – ANSI 81
Frequency protection detects abnormal system frequency.
It can be used in underfrequency and overfrequency protection schemes.
8.10 Circuit Breaker Failure – ANSI 50BF
Breaker failure protection supervises the successful interruption of current following a trip command.
If the circuit breaker fails to clear the fault within the configured time, the protection scheme can initiate backup tripping.
8.11 Automatic Reclosing – ANSI 79
Automatic reclosing can be applied in overhead line and feeder protection schemes to restore supply following temporary faults.
The availability and implementation depend on the individual relay model and configuration.
8.12 Synchronism Check – ANSI 25
Synchronism check supervises the electrical conditions across a circuit breaker before closing two energized systems together.
This function is particularly relevant to the 7SJ64.
9. DIGSI 4 – Configuration and Parameterization of SIPROTEC 4 7SJ Relays
DIGSI 4 is Siemens engineering software for configuring SIPROTEC 4 protection relays.
It provides a common engineering environment for the 7SJ61, 7SJ62, 7SJ63, 7SJ64 and 7SJ66.
Important engineering activities include:
- Creating a new DIGSI 4 project.
- Selecting the correct SIPROTEC 4 relay.
- Entering the device order number.
- Configuring hardware and communication interfaces.
- Setting CT and VT parameters.
- Configuring protection functions.
- Entering protection settings.
- Assigning binary inputs and outputs.
- Configuring LEDs and indications.
- Creating logic using CFC where supported.
- Configuring communication.
- Transferring configuration to the relay.
- Reading events and disturbance records.
9.1 Protection Parameterization
The main protection parameters include:
- CT primary and secondary ratings.
- Rated voltage.
- Rated frequency.
- Overcurrent pickup values.
- Earth fault pickup values.
- Time multipliers.
- Characteristic curves.
- Directional protection settings.
- Thermal model parameters.
- Voltage protection thresholds.
- Frequency protection thresholds.
All settings should be calculated and approved through the project’s protection coordination study.
9.2 Binary Input and Output Configuration
Binary inputs and outputs are essential for protection and control integration.
Typical binary input signals:
- Circuit breaker open.
- Circuit breaker closed.
- Disconnector position.
- Earthing switch position.
- External protection trip.
- External blocking.
- Local/remote selection.
Typical binary output signals:
- Circuit breaker trip.
- Circuit breaker close.
- General alarm.
- Protection start.
- Protection operation.
- External interlocking.
9.3 CFC Logic Configuration
Continuous Function Chart (CFC) is used for creating additional logic functions in supported SIPROTEC 4 devices.
Examples include:
- Alarm aggregation.
- Trip logic.
- Interlocking logic.
- External signal processing.
- Blocking conditions.
- Custom indications.
CFC is especially useful when standard protection and control functions need additional project-specific logic.
10. IEC 61850 and Communication in SIPROTEC 4 7SJ Relays
The SIPROTEC 4 7SJ family can be integrated into substation automation systems using supported communication interfaces and protocols.
Depending on the device version, communication options may include:
- IEC 61850.
- IEC 60870-5-103.
- PROFIBUS.
- Modbus, where supported.
- DIGSI communication.
IEC 61850 Engineering
Important concepts include:
- Logical Devices (LD).
- Logical Nodes (LN).
- Data Objects (DO).
- Data Attributes (DA).
- MMS communication.
- GOOSE messaging.
- ICD files.
- CID files.
- SCL engineering.
- Station bus architecture.
GOOSE Communication
GOOSE messaging enables high-speed communication between IEDs.
Typical applications include:
- Circuit breaker interlocking.
- Protection blocking.
- Transfer trip.
- Breaker failure signals.
- Busbar-related signals.
- Inter-IED protection logic.
Engineers should verify the supported IEC 61850 edition, firmware and communication capabilities of each relay before preparing an engineering project.
11. Testing and Commissioning of SIPROTEC 4 7SJ Relays
Testing is a critical part of the protection system lifecycle.
The same general commissioning methodology applies to the entire 7SJ family, although individual protection tests depend on the selected model and available functions.
11.1 Visual and Hardware Inspection
- Verify relay model and order number.
- Check auxiliary power supply.
- Inspect CT and VT wiring.
- Verify binary input connections.
- Verify binary output connections.
- Check communication connections.
11.2 CT and VT Testing
- CT ratio verification.
- CT polarity verification.
- Phase identification.
- VT ratio verification.
- Phase rotation verification.
- Secondary circuit continuity.
11.3 Overcurrent Protection Testing
Using a secondary injection test set:
- Verify pickup current.
- Verify dropout current.
- Measure operating time.
- Test instantaneous stages.
- Test inverse-time characteristics.
- Verify trip output.
11.4 Earth Fault Protection Testing
Inject the required residual or earth fault current and verify the operating threshold and timing.
11.5 Directional Protection Testing
For models configured with directional protection:
- Verify voltage polarization.
- Verify current polarity.
- Check directional operating angle.
- Test forward operation.
- Test reverse blocking.
- Verify directional earth fault characteristics.
11.6 Synchronism Check Testing
For the 7SJ64 and other supported configurations:
- Verify voltage inputs.
- Verify phase angle measurement.
- Verify frequency difference.
- Test voltage difference supervision.
- Check closing permission.
- Verify breaker closing time compensation where applicable.
11.7 Binary I/O and Circuit Breaker Testing
Check all configured inputs, outputs, trip circuits and control commands.
11.8 Communication Testing
Verify:
- Communication connectivity.
- Protocol configuration.
- Signal mapping.
- IEC 61850 data exchange, where supported.
- GOOSE publishing and subscription, where configured.
- Time synchronization.
OMICRON CMC equipment and Test Universe software can be used for comprehensive secondary injection testing.
12. Disturbance Recording and Fault Analysis
SIPROTEC 4 relays provide event and disturbance recording capabilities.
Engineers can retrieve records and analyse the operation of the protection system.
Important information includes:
- Phase current waveforms.
- Residual current.
- Voltage waveforms, where available.
- Protection start signals.
- Trip signals.
- Binary input states.
- Binary output states.
- Event timestamps.
SIGRA can be used for analysing supported disturbance recording files.
Fault analysis is important for understanding why a relay operated and whether the protection scheme performed correctly.
13. Common Troubleshooting Problems
| Problem | Possible cause |
|---|---|
| Incorrect current measurement | CT wiring or polarity error |
| Unwanted overcurrent trip | Incorrect pickup or coordination |
| Unwanted earth fault operation | Incorrect residual current measurement |
| Directional protection failure | Incorrect voltage/current polarity or settings |
| Relay does not communicate | Protocol or interface configuration |
| Binary input not detected | Wiring or configuration issue |
| Breaker does not trip | Trip circuit or output assignment problem |
| Incorrect synchronism check | Incorrect voltage connections or settings |
| Unexpected protection operation | Incorrect parameterization or logic |
Troubleshooting must be carried out using the approved relay configuration, drawings and protection study.
14. Advantages of SIPROTEC 4 7SJ Protection Relays
The main advantages include:
- Multifunction numerical protection.
- Integrated monitoring and measurement.
- Flexible configuration using DIGSI 4.
- Different hardware configurations for different applications.
- Communication with substation automation systems.
- Event and disturbance recording.
- Configurable protection and control logic.
- Application in industrial and utility distribution networks.
- Integration into existing Siemens protection systems.
15. SIPROTEC 4 7SJ Series Training by Elec-Engg
At Elec-Engg, we provide professional technical training in Siemens SIPROTEC protection relays, DIGSI engineering and substation automation.
Our courses are designed for electrical engineers working in protection, commissioning, operation, maintenance and substation automation.
Our SIPROTEC 4 training includes:
- Complete introduction to SIPROTEC 4.
- 7SJ61, 7SJ62, 7SJ63, 7SJ64 and 7SJ66 relay models.
- Protection functions and ANSI codes.
- Overcurrent and earth fault protection.
- Directional overcurrent and earth fault protection.
- Protection setting calculations.
- DIGSI 4 project creation and configuration.
- Binary input and output configuration.
- CFC logic engineering.
- IEC 61850 and GOOSE communication.
- Relay testing using OMICRON CMC.
- Disturbance record analysis using SIGRA.
- Commissioning and troubleshooting.
Our training delivery methods:
- Online technical courses.
- Structured self-paced training.
- Customized training for companies and utilities.
- Face-to-face training.
- Practical engineering exercises and real-world case studies.
We also provide customized training based on the actual relay models, protection schemes and engineering requirements of your company.
Whether you are a protection engineer, commissioning engineer or substation automation specialist, our objective is to help you develop practical engineering skills rather than simply understand theoretical protection principles.
Training and technical information:
Website: https://elec-engg.com/
Practical Courses by Dr Saeed Roostaee / Elec-Engg
16. Conclusion
The Siemens SIPROTEC 4 7SJ series provides a comprehensive range of numerical protection solutions for medium-voltage and high-voltage feeder applications.
The 7SJ61, 7SJ62, 7SJ63, 7SJ64 and 7SJ66 offer different hardware configurations and engineering capabilities to meet different protection and control requirements.
Understanding the differences between these models, their protection functions, DIGSI 4 configuration, communication capabilities and testing procedures is essential for protection and substation automation engineers.
With proper engineering, parameterization and commissioning, SIPROTEC 4 7SJ relays can provide dependable protection and monitoring for electrical power systems.
