Siemens SIPROTEC 5 7VK87 Circuit-Breaker Management Relay: Functions & Settings

Table Of Contents
  1. 1. Introduction to SIPROTEC 5 7VK87
  2. 2. Main Applications of 7VK87
  3. 3. Main Functions of SIPROTEC 5 7VK87
  4. 4. Automatic Reclosing – ANSI 79
  5. 5. Single-Pole and Three-Pole Automatic Reclosing
  6. 6. Synchrocheck and Synchronization – ANSI 25
  7. 7. Automatic Synchronization
  8. 8. Circuit-Breaker Failure Protection – ANSI 50BF
  9. 9. Breaker-and-a-Half Scheme Applications
  10. 10. Circuit-Breaker Control and Supervision
  11. 11. Trip-Circuit Supervision – ANSI 74TC
  12. 12. Point-on-Wave Switching
  13. 13. Circuit-Breaker Wear Monitoring
  14. 14. Circuit-Breaker Restrike Monitoring
  15. 15. Additional Protection and Monitoring Functions
  16. 16. DIGSI 5 Engineering for 7VK87
  17. 17. IEC 61850 Communication in 7VK87
  18. 18. Testing and Commissioning of SIPROTEC 5 7VK87
  19. 19. Omicron CMC Testing of 7VK87
  20. 20. Common 7VK87 Engineering and Commissioning Problems
  21. 21. SIPROTEC 5 7VK87 vs. Separate Protection and Control Devices
  22. 22. Important Documents for a 7VK87 Project
  23. 23. Siemens SIPROTEC 5 7VK87 Training by Elec-Engg
  24. 24. Conclusion

Siemens SIPROTEC 5 7VK87 Circuit-Breaker Management Relay: Functions, Applications, Settings, DIGSI 5 and Testing

1. Introduction to SIPROTEC 5 7VK87

Circuit breakers are essential components of electrical power systems. They connect and disconnect electrical circuits during normal operation and interrupt fault currents when protection systems detect abnormal conditions.

Reliable circuit-breaker management requires more than a simple trip command. Modern protection systems must coordinate automatic reclosing, synchronization checks, circuit-breaker failure protection, switching operations, interlocking and breaker condition monitoring.

The Siemens SIPROTEC 5 7VK87 is a modular numerical circuit-breaker management device specifically designed for these applications.

Unlike conventional feeder protection relays, the 7VK87 is primarily intended to manage circuit-breaker operations and coordinate associated protection and control functions.

Its main functions include:

  • Automatic reclosing (ANSI 79).
  • Synchrocheck and synchronization (ANSI 25).
  • Circuit-breaker failure protection (ANSI 50BF).
  • One-pole and three-pole circuit-breaker management.
  • Circuit-breaker control and supervision.
  • Switchgear interlocking.
  • Point-on-wave switching in applicable configurations.
  • Circuit-breaker monitoring.
  • Fault recording and disturbance analysis.
  • IEC 61850 communication and GOOSE messaging.

The 7VK87 is engineered using DIGSI 5, Siemens’ engineering software for the SIPROTEC 5 family.

2. Main Applications of 7VK87

The 7VK87 can be applied in different substation and power system arrangements.

Typical applications include:

  • High-voltage transmission substations.
  • Extra-high-voltage substations.
  • Transmission line circuit breakers.
  • Single-pole and three-pole tripping applications.
  • Automatic reclosing schemes.
  • Breaker-and-a-half switchgear arrangements.
  • Generator synchronization applications.
  • Bus coupler and bus section circuit breakers.
  • Circuit-breaker failure protection.
  • Switching and interlocking applications.

The device is particularly useful where circuit-breaker management functions are separated from the main line or transformer protection relay.

For example, a distance protection relay such as the SIPROTEC 5 7SA87 can detect a transmission-line fault and send a trip command to the 7VK87. The 7VK87 then manages the associated circuit-breaker operations, automatic reclosing and breaker failure functions according to the configured scheme.

3. Main Functions of SIPROTEC 5 7VK87

The following table summarizes important functions available in the 7VK87 platform. The actual functional scope depends on the ordered hardware, firmware and configuration.

ANSI codeFunctionApplication
25Synchrocheck and synchronizationVerifies synchronism before closing
27Undervoltage protectionMonitors abnormal voltage
32Power protectionMonitors active and reactive power
37Undercurrent protectionDetects reduced current
38Temperature supervisionMonitors temperature
46Negative-sequence protectionDetects unbalanced current
50BFCircuit-breaker failure protectionDetects failure to interrupt current
59Overvoltage protectionMonitors excessive voltage
67Directional overcurrent protectionDirectional backup protection
74TCTrip-circuit supervisionMonitors trip circuit integrity
79Automatic reclosingRecloses a circuit breaker after a fault
81Frequency protectionMonitors abnormal frequency
86LockoutProvides lockout and reset functionality

Additional functions include point-on-wave switching, breaker wear monitoring, circuit-breaker restrike monitoring, fault recording, power quality measurement and control logic, depending on the configuration.

4. Automatic Reclosing – ANSI 79

Automatic reclosing is one of the most important functions of the 7VK87.

In overhead transmission and distribution systems, many faults are temporary. Examples include lightning, temporary contact with vegetation, pollution flashover and transient insulation breakdown.

After the protection relay trips the circuit breaker, the fault may disappear. Automatic reclosing attempts to restore the electrical connection without requiring manual intervention.

4.1 Operating principle

A typical automatic reclosing sequence includes:

  1. A protection relay detects a fault.
  2. The protection relay sends a trip command.
  3. The circuit breaker opens.
  4. The automatic reclosing function starts.
  5. The configured dead time begins.
  6. The required voltage and synchronization conditions are checked.
  7. The circuit breaker receives a closing command.
  8. The system evaluates whether the reclosure was successful.

If the fault has disappeared, the line returns to service.

If the fault remains, the protection system trips the circuit breaker again.

4.2 Single-shot and multi-shot reclosing

Depending on the protection philosophy and configured application, automatic reclosing can use different sequences.

Single-shot reclosing

One automatic closing attempt is made following the initial trip.

Multi-shot reclosing

More than one reclosing attempt can be configured, with different dead times and operating conditions.

The permitted number of shots depends on the circuit-breaker capability, network requirements and protection philosophy.

4.3 Important automatic reclosing settings

Typical settings include:

  • Automatic reclosing enable/disable.
  • Single-pole or three-pole operation.
  • Dead time.
  • Reclaim time.
  • Number of shots.
  • Closing command duration.
  • Dead-line detection.
  • Dead-bus detection.
  • Live-line detection.
  • Live-bus detection.
  • Synchronism check.
  • Reclosing lockout conditions.
  • External blocking signals.
  • Circuit-breaker readiness.

The settings must be coordinated with the transmission line, circuit breaker, protection relays and network operating requirements.

5. Single-Pole and Three-Pole Automatic Reclosing

Transmission line protection systems may use single-pole or three-pole tripping.

5.1 Single-pole tripping

Single-pole tripping is commonly applied on high-voltage transmission lines where phase-to-earth faults are frequent.

When a single-phase earth fault occurs, only the faulty phase circuit breaker pole is opened.

The healthy phases remain connected to the network.

After the configured dead time, the faulty phase is reclosed if the required conditions are satisfied.

Advantages include:

  • Improved power system stability.
  • Reduced interruption of power transfer.
  • Better utilization of transmission lines.
  • Reduced disturbance to connected generators.

5.2 Three-pole tripping

For phase-to-phase faults, three-phase faults or other conditions requiring three-pole operation, all three circuit-breaker poles are opened.

After the configured dead time, the automatic reclosing function may initiate a three-pole closing operation.

5.3 Engineering considerations

The protection engineer must define:

  • Which protection functions initiate single-pole tripping.
  • Which functions initiate three-pole tripping.
  • Which protection functions initiate automatic reclosing.
  • Which functions block automatic reclosing.
  • Whether single-pole or three-pole dead time is used.
  • Whether synchronism check is required.
  • How unsuccessful reclosing is handled.

Correct coordination between the main protection relay and the 7VK87 is essential.

6. Synchrocheck and Synchronization – ANSI 25

Synchrocheck is used to verify that two electrical systems are suitable for connection before a circuit breaker is closed.

Closing a circuit breaker between unsynchronized systems can cause severe electrical and mechanical stress.

The 7VK87 includes synchronization and synchrocheck functionality.

6.1 Basic operating principle

The synchrocheck function evaluates voltage measurements from two sides of a circuit breaker.

Typical parameters include:

  • Voltage magnitude difference.
  • Frequency difference.
  • Phase-angle difference.
  • Slip frequency.
  • Phase sequence.
  • Dead-line and live-line conditions.

The closing command is permitted only when the configured conditions are satisfied.

6.2 Voltage difference

The voltage difference between the two sides can be expressed as:

[
\Delta U=|U_1-U_2|
]

The relay compares this difference with the configured permissible threshold.

6.3 Frequency difference

The frequency difference is:

[
\Delta f=|f_1-f_2|
]

A large frequency difference indicates that the two systems are not operating sufficiently close to the same frequency.

6.4 Phase-angle difference

The phase-angle difference is another critical parameter.

The two voltage phasors must be sufficiently close in phase before closing.

The allowable difference depends on the power system application and circuit-breaker characteristics.

6.5 Important synchrocheck settings

  • Voltage difference threshold.
  • Frequency difference threshold.
  • Phase-angle difference threshold.
  • Slip frequency.
  • Live-line voltage threshold.
  • Dead-line voltage threshold.
  • Measurement supervision.
  • Synchronism permission time.
  • Closing command conditions.

The settings must be coordinated with the circuit-breaker closing time and the network synchronization requirements.

7. Automatic Synchronization

Automatic synchronization is different from a simple synchrocheck function.

Synchrocheck verifies whether the conditions for closing are satisfied.

Automatic synchronization can actively adjust generator or system operating conditions to achieve synchronism before closing.

Depending on the application and configured function scope, synchronization may involve:

  • Frequency adjustment.
  • Voltage adjustment.
  • Phase-angle monitoring.
  • Closing command calculation.
  • Generator control signals.

Typical applications include generator synchronization and reconnection of electrical systems.

For generator synchronization projects, the engineer must consider the generator voltage regulator, governor, synchronization equipment and circuit-breaker closing characteristics.

8. Circuit-Breaker Failure Protection – ANSI 50BF

Circuit-breaker failure protection is another fundamental function of the 7VK87.

When a protection relay detects a fault, it sends a trip command to the associated circuit breaker.

If the circuit breaker fails to open, the fault current may continue flowing.

This condition can cause serious damage to equipment and threaten power system stability.

The 7VK87 can provide circuit-breaker failure protection for single-pole and three-pole tripping applications.

8.1 Operating principle

A typical breaker failure sequence includes:

  1. A protection relay issues a trip command.
  2. The breaker failure protection receives the initiation signal.
  3. A timer starts.
  4. The circuit-breaker current is monitored.
  5. The relay checks whether the breaker has successfully interrupted the current.
  6. If current remains above the configured threshold after the delay, breaker failure is declared.
  7. Backup tripping is initiated.

8.2 Current supervision

Current supervision is important because the circuit breaker must interrupt the fault current.

The protection engineer configures the appropriate current thresholds and phase-specific logic.

For single-pole applications, the scheme must identify which phase remains conducting.

8.3 Breaker failure stages

Depending on the protection scheme, breaker failure protection may use more than one tripping stage.

Stage 1

Initiates the required backup trip logic to clear the fault.

Stage 2

Can initiate additional tripping, such as remote intertripping or further isolation, if the fault remains.

The exact stages and output assignments depend on the network protection philosophy.

8.4 Important 50BF settings

  • Breaker failure initiation.
  • Current supervision threshold.
  • Phase-specific current detection.
  • Timer settings.
  • Reset conditions.
  • Breaker position supervision.
  • Trip T1 logic.
  • Trip T2 logic.
  • Backup trip outputs.
  • Remote intertrip signals.

The breaker failure delay must consider the circuit-breaker opening time, current interruption time, auxiliary contact behavior and safety margin.

9. Breaker-and-a-Half Scheme Applications

The 7VK87 is suitable for applications involving breaker-and-a-half switchgear arrangements.

In a breaker-and-a-half configuration, two busbars and three circuit breakers are used for two electrical circuits.

Each circuit is connected between two circuit breakers, with a shared middle breaker.

The protection and control arrangement must correctly manage:

  • Circuit-breaker trip commands.
  • Automatic reclosing.
  • Synchrocheck.
  • Breaker failure protection.
  • Circuit isolation.
  • Switching interlocking.

In these arrangements, correct assignment of each protection function to the relevant circuit breaker is especially important.

The 7VK87 can be configured to manage the associated circuit-breaker functions, subject to the selected architecture and device configuration.

10. Circuit-Breaker Control and Supervision

The 7VK87 provides circuit-breaker management capabilities beyond automatic reclosing and breaker failure protection.

Typical control and supervision applications include:

  • Circuit-breaker opening.
  • Circuit-breaker closing.
  • Local and remote control.
  • Circuit-breaker position indication.
  • Trip circuit supervision.
  • Closing circuit supervision.
  • Switching operation monitoring.
  • Interlocking.
  • Operation counter.
  • Breaker status supervision.

The circuit-breaker function group represents the physical circuit breaker in the SIPROTEC 5 engineering structure.

It processes control commands, auxiliary contacts and relevant breaker information.

11. Trip-Circuit Supervision – ANSI 74TC

Trip-circuit supervision monitors the integrity of the circuit-breaker trip circuit.

A failure in the trip circuit can prevent a circuit breaker from opening when a protection relay issues a trip command.

Typical problems include:

  • Loss of DC supply.
  • Open trip coil circuit.
  • Damaged wiring.
  • Blown fuse.
  • Defective auxiliary contacts.
  • Incorrect terminal connections.

Trip-circuit supervision can detect abnormal conditions and generate an alarm.

Depending on the configured supervision arrangement, it may monitor the trip circuit using one or more binary inputs.

Important engineering considerations include:

  • Trip coil arrangement.
  • DC supply.
  • Auxiliary contacts.
  • Supervision resistor.
  • Binary input configuration.
  • Alarm output.
  • Trip circuit wiring.

Trip-circuit supervision should be tested during commissioning and maintenance.

12. Point-on-Wave Switching

Point-on-wave switching is used to control the exact instant at which a circuit breaker opens or closes relative to the AC waveform.

The objective is to reduce switching transients and improve equipment performance.

Applications can include:

  • Transformer energization.
  • Reactor switching.
  • Capacitor bank switching.
  • Other switching applications where controlled switching is beneficial.

For example, controlled transformer energization can reduce magnetizing inrush under suitable conditions.

The point-on-wave function considers switching conditions and the relevant electrical waveform.

Important parameters include:

  • Voltage waveform.
  • Current waveform.
  • Circuit-breaker operating time.
  • Closing time variation.
  • Pole discrepancy.
  • Target switching point.
  • Operating conditions.

The circuit-breaker mechanical characteristics and the specific switching application must be considered carefully.

Point-on-wave functionality is subject to the appropriate device configuration and engineering documentation.

13. Circuit-Breaker Wear Monitoring

Circuit breakers experience mechanical and electrical wear during switching operations.

The amount of wear depends on factors such as:

  • Interrupted current.
  • Number of switching operations.
  • Fault current magnitude.
  • Contact material.
  • Operating mechanism.
  • Maintenance condition.

The 7VK87 supports circuit-breaker monitoring functions in applicable configurations.

Examples include:

  • Switching operation counters.
  • Accumulated breaking current.
  • I²t-related monitoring.
  • Circuit-breaker wear statistics.
  • Switching time supervision.
  • Circuit-breaker status monitoring.

These functions can help maintenance engineers evaluate the operating history of circuit breakers and plan maintenance activities.

They do not replace the circuit-breaker manufacturer’s inspection and maintenance requirements.

14. Circuit-Breaker Restrike Monitoring

Circuit-breaker restrike monitoring is used to identify abnormal electrical behavior associated with switching operations.

A restrike can occur when the dielectric strength across the opening contacts is insufficient to withstand the recovery voltage.

The 7VK87 catalog identifies circuit-breaker restrike monitoring as an available function in its functional scope.

The actual monitoring method, required measurements and configuration must be checked against the applicable device manual and circuit-breaker application.

15. Additional Protection and Monitoring Functions

The 7VK87 is primarily a circuit-breaker management device, but its functional scope can include additional protection and monitoring functions.

Depending on configuration, these can include:

  • Overcurrent protection.
  • Directional overcurrent protection.
  • Overvoltage protection.
  • Undervoltage protection.
  • Frequency protection.
  • Undercurrent protection.
  • Negative-sequence protection.
  • Temperature supervision.
  • Arc protection.
  • Fault recording.
  • Power quality basic measurements.
  • External trip initiation.

These functions can provide backup protection or additional monitoring.

The 7VK87 should not automatically be considered a replacement for a dedicated line, transformer or generator protection relay. The main protection philosophy must define which device performs primary fault detection and which device manages circuit-breaker operations.

16. DIGSI 5 Engineering for 7VK87

DIGSI 5 is used to configure and manage the SIPROTEC 5 7VK87.

A typical engineering workflow includes the following steps.

16.1 Create a new project

  • Open DIGSI 5.
  • Create a new project.
  • Add the SIPROTEC 5 7VK87.
  • Select the correct device variant.
  • Verify the firmware version.
  • Select the circuit-breaker management application template.

16.2 Configure hardware

Configure the actual hardware according to the relay order number.

Typical configuration items include:

  • Current transformer inputs.
  • Voltage transformer inputs.
  • Binary inputs.
  • Binary outputs.
  • Communication modules.
  • Auxiliary power supply.
  • Additional I/O modules.

The available I/O quantity depends on the ordered hardware and modular expansion.

16.3 Configure measuring points

The 7VK87 can use voltage and current measurements for synchronization, breaker failure protection and other configured functions.

Typical measurement arrangements include:

  • Three-phase current.
  • Three-phase voltage.
  • Single-phase voltage.
  • Busbar-side voltage.
  • Line-side voltage.
  • Generator-side voltage.

The measurement assignment must match the actual CT and VT connections.

16.4 Configure the circuit-breaker function group

The circuit-breaker function group represents the physical circuit breaker.

Configure:

  • Circuit-breaker position.
  • Open command.
  • Close command.
  • Trip signals.
  • Auxiliary contacts.
  • Trip circuit supervision.
  • Closing circuit supervision.
  • Switching counters.
  • Breaker status.

16.5 Configure automatic reclosing

Configure the automatic reclosing function according to the protection philosophy.

Important settings include:

  • Reclosing mode.
  • Single-pole or three-pole operation.
  • Dead time.
  • Reclaim time.
  • Number of shots.
  • Synchronism check.
  • Dead-line and live-line conditions.
  • Blocking signals.
  • External initiation.

16.6 Configure synchrocheck

Assign the voltage measurement points and configure the relevant synchronization conditions.

Verify:

  • Voltage measurement.
  • Frequency measurement.
  • Phase-angle difference.
  • Slip frequency.
  • Live-line and dead-line conditions.
  • Closing permission.

16.7 Configure breaker failure protection

Configure:

  • Breaker failure initiation.
  • Current supervision.
  • Phase-specific logic.
  • Timer stages.
  • Reset conditions.
  • Backup trip outputs.
  • Remote intertrip.
  • Trip T1 and T2.

16.8 Configure circuit-breaker interaction

One of the important DIGSI 5 engineering tasks is defining how the protection functions interact with the circuit-breaker function groups.

For example, the engineer must define:

  • Which protection functions initiate trip commands.
  • Which functions initiate automatic reclosing.
  • Which functions block automatic reclosing.
  • Which functions start breaker failure protection.

This configuration is particularly important when the 7VK87 is connected to separate main protection relays.

17. IEC 61850 Communication in 7VK87

The 7VK87 supports modern communication capabilities for integration into substation automation systems.

Depending on the hardware and firmware configuration, communication can include:

  • IEC 61850-8-1 MMS.
  • GOOSE messaging.
  • IEC 60870-5-103.
  • Modbus TCP.
  • PROFINET IO.
  • Other supported communication interfaces.

17.1 GOOSE communication

GOOSE communication can be used to exchange protection and control signals between IEDs.

Typical applications include:

  • Trip initiation.
  • Automatic reclosing initiation.
  • Automatic reclosing blocking.
  • Breaker failure initiation.
  • Circuit-breaker status.
  • Interlocking signals.
  • Synchronization permissive.
  • External protection signals.

For example, a 7SA87 distance protection relay can send an appropriate trip or status signal to the 7VK87 using binary I/O or IEC 61850 GOOSE communication.

The 7VK87 then performs the configured circuit-breaker management sequence.

17.2 SCL engineering

IEC 61850 SCL files are used to configure the communication relationships between IEDs.

Common file types include:

  • ICD.
  • CID.
  • SCD.
  • IID.

The engineer must verify:

  • Dataset configuration.
  • GOOSE control blocks.
  • Publisher and subscriber assignments.
  • Signal mapping.
  • Network configuration.
  • Communication supervision.

17.3 Time synchronization

Correct time synchronization is important for event analysis and disturbance recording.

The communication and time synchronization design should be checked against the selected device configuration and station architecture.

18. Testing and Commissioning of SIPROTEC 5 7VK87

Commissioning is essential to verify the complete circuit-breaker management scheme.

Testing should cover hardware, measurement circuits, automatic reclosing, synchrocheck, breaker failure, control logic and communication.

18.1 Hardware inspection

Check:

  • Device model and order number.
  • Auxiliary DC supply.
  • Earthing.
  • CT wiring.
  • VT wiring.
  • Binary inputs.
  • Binary outputs.
  • Circuit-breaker trip circuit.
  • Circuit-breaker closing circuit.
  • Communication interfaces.

18.2 CT and VT testing

Verify:

  • CT ratio.
  • CT polarity.
  • VT ratio.
  • Phase sequence.
  • Phase identification.
  • Measurement assignment.
  • Secondary circuit grounding.
  • Circuit continuity.

Incorrect voltage phase association can cause synchrocheck to operate incorrectly.

18.3 Automatic reclosing testing

Test:

  • Reclosing initiation.
  • Single-pole operation.
  • Three-pole operation.
  • Dead time.
  • Reclaim time.
  • Number of shots.
  • Reclosing blocking.
  • Reclosing lockout.
  • Successful closing.
  • Unsuccessful reclosing.

The test should verify the complete sequence from protection trip initiation to the final closing command.

18.4 Synchrocheck testing

Test the following conditions:

  • Voltage difference within limits.
  • Voltage difference outside limits.
  • Frequency difference within limits.
  • Frequency difference outside limits.
  • Phase angle within limits.
  • Phase angle outside limits.
  • Live-line and dead-line conditions.
  • Closing permission.
  • Closing blocking.

18.5 Circuit-breaker failure testing

Simulate a breaker failure condition.

Verify:

  • Breaker failure initiation.
  • Current supervision.
  • Timer operation.
  • Breaker opening detection.
  • Trip T1.
  • Trip T2.
  • Remote intertrip.
  • Reset conditions.

18.6 Trip-circuit supervision testing

Verify:

  • Healthy trip circuit indication.
  • Loss of DC supply.
  • Open circuit conditions.
  • Binary input response.
  • Alarm generation.
  • Restoration of the trip circuit.

18.7 IEC 61850 testing

Verify:

  • MMS communication.
  • GOOSE publisher and subscriber.
  • Trip initiation signals.
  • Reclosing initiation signals.
  • Blocking signals.
  • Breaker status.
  • Communication supervision.
  • Time synchronization.

Tools such as IEDScout and Wireshark can help with IEC 61850 communication analysis.

19. Omicron CMC Testing of 7VK87

Omicron CMC test equipment and Test Universe can be used to test measurement-dependent functions and protection logic.

Typical tests include:

  • Synchrocheck.
  • Voltage supervision.
  • Frequency protection.
  • Overcurrent protection.
  • Directional overcurrent protection.
  • Negative-sequence protection.
  • Undervoltage and overvoltage.
  • Breaker failure current supervision.
  • Binary input/output testing.
  • Automatic reclosing sequence verification.

For automatic reclosing and breaker failure applications, binary signal simulation is particularly important.

The test equipment should simulate the required trip, breaker position, current and voltage conditions.

A complete test should verify both the relay logic and the actual circuit-breaker control circuits.

20. Common 7VK87 Engineering and Commissioning Problems

Incorrect VT phase assignment

Incorrect voltage phase assignment can result in incorrect synchrocheck calculations and unwanted closing permission or blocking.

Incorrect synchronization settings

Incorrect voltage, frequency or phase-angle thresholds can prevent successful synchronization or permit closing under unsuitable conditions.

Incorrect automatic reclosing initiation

If the main protection relay does not send the correct initiation signal, automatic reclosing may not start.

Incorrect reclosing blocking logic

Failure to configure the required blocking conditions can result in unwanted reclosing after serious faults.

Incorrect circuit-breaker position feedback

Incorrect auxiliary contact wiring can cause the relay to identify the wrong breaker state.

Incorrect breaker failure current threshold

An incorrect threshold may cause failure to detect a breaker that remains closed or unwanted breaker failure operation.

Incorrect breaker failure time delay

A delay that is too short can cause unnecessary backup tripping. A delay that is too long can increase fault-clearing time.

Incorrect trip matrix

A protection signal may be received but not connected to the intended circuit-breaker trip output.

GOOSE communication failure

Incorrect datasets, publisher/subscriber assignments or network settings can prevent communication between the main protection relay and the 7VK87.

Incorrect single-pole and three-pole logic

The wrong trip mode can result in unnecessary three-phase interruption or incorrect automatic reclosing operation.

21. SIPROTEC 5 7VK87 vs. Separate Protection and Control Devices

In traditional protection schemes, separate devices may be used for:

  • Automatic reclosing.
  • Synchrocheck.
  • Circuit-breaker failure protection.
  • Circuit-breaker control.
  • Trip circuit supervision.

The 7VK87 integrates these circuit-breaker management functions into a modular SIPROTEC 5 platform.

FeatureSeparate devicesSIPROTEC 5 7VK87
Automatic reclosingSeparate relay or protection deviceIntegrated function
SynchrocheckSeparate synchronization relayIntegrated function
Breaker failureSeparate breaker failure relayIntegrated function
Circuit-breaker managementDistributed equipmentIntegrated engineering platform
CommunicationDepends on device combinationSIPROTEC 5 communication platform
EngineeringMultiple tools may be requiredDIGSI 5
Logic coordinationExternal wiring and logicConfigurable device logic and communication

The final architecture should be selected according to project requirements, redundancy, protection independence and applicable standards.

22. Important Documents for a 7VK87 Project

A complete circuit-breaker management project should include:

  • Substation single-line diagram.
  • Protection philosophy.
  • Circuit-breaker data sheet.
  • CT and VT data sheets.
  • AC schematic diagrams.
  • DC schematic diagrams.
  • Trip and close circuit diagrams.
  • Automatic reclosing philosophy.
  • Synchrocheck settings.
  • Breaker failure settings.
  • I/O list.
  • GOOSE signal list.
  • DIGSI 5 project.
  • IEC 61850 SCL files.
  • Commissioning test procedures.
  • Protection test reports.
  • Circuit-breaker timing reports.
  • Final as-built documentation.

These documents are important for correct engineering, testing, operation and future maintenance.

23. Siemens SIPROTEC 5 7VK87 Training by Elec-Engg

Elec-Engg provides practical training in power system protection, circuit-breaker management and substation automation, including Siemens SIPROTEC 5 and DIGSI 5 engineering.

Our training focuses on the practical application of protection and control functions.

Training topics can include:

  • SIPROTEC 5 7VK87 hardware and architecture.
  • DIGSI 5 project creation.
  • Circuit-breaker function groups.
  • Automatic reclosing.
  • Single-pole and three-pole tripping.
  • Synchrocheck and synchronization.
  • Circuit-breaker failure protection.
  • Trip-circuit supervision.
  • Circuit-breaker control and interlocking.
  • Point-on-wave switching.
  • Breaker monitoring.
  • IEC 61850 and GOOSE communication.
  • CFC logic engineering.
  • Omicron CMC and Test Universe testing.
  • Commissioning and troubleshooting.

Training formats include:

  • Online training: Instructor-led technical courses.
  • Structured self-paced training: Organized lessons, practical exercises and learning materials.
  • Face-to-face training: Classroom and practical engineering sessions.
  • Customized in-house training: Programs designed around company requirements, installed protection systems and project applications.

Our objective is to help protection, commissioning, operation and maintenance engineers develop practical skills for configuring, testing and troubleshooting circuit-breaker management systems.

Visit Elec-Engg.com to explore our power system protection and substation automation training programs or contact us to discuss customized training.

24. Conclusion

The Siemens SIPROTEC 5 7VK87 is a modular circuit-breaker management device designed for modern power system applications.

Its main functions include automatic reclosing, synchrocheck, synchronization and circuit-breaker failure protection. Additional capabilities include circuit-breaker control, interlocking, supervision, monitoring and communication.

The device is particularly valuable in transmission substations, single-pole tripping applications and complex switchgear arrangements such as breaker-and-a-half configurations.

Correct engineering of automatic reclosing, synchronization conditions, breaker failure logic, trip circuits and IEC 61850 communication is essential for reliable operation.

For protection and commissioning engineers, practical knowledge of DIGSI 5 and the interaction between main protection relays and circuit-breaker management devices is important for successful implementation.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top