- 1. Introduction
- 2. What Is Overvoltage Protection (ANSI 59)?
- 3. What Is Undervoltage Protection (ANSI 27)?
- 4. Voltage Protection Measurement Principles
- 5. Overvoltage Protection Characteristics
- 6. Undervoltage Protection Characteristics
- 7. Per-Unit Voltage Calculations
- 8. Generator Overvoltage Protection
- 9. Generator Undervoltage Protection
- 10. Transformer Overvoltage and Undervoltage Protection
- 11. Motor Undervoltage Protection
- 12. Feeder and Distribution Applications
- 13. Phase Undervoltage and Positive-Sequence Undervoltage
- 14. Residual Overvoltage and Earth-Fault Detection
- 15. Voltage Protection Settings and Coordination
- 16. Practical Calculation Example: 33 kV Bus Undervoltage
- 17. GE Multilin Voltage Protection Applications
- 18. General GE Multilin Configuration Workflow
- 19. Voltage Protection Testing and Commissioning
- 20. Common Voltage Protection Problems
- 21. Voltage Protection Commissioning Checklist
- 22. Best Engineering Practices
- 23. Training on GE Multilin Protection Relays by Elec-Engg
- 24. Frequently Asked Questions
- What is ANSI 27 protection?
- What is ANSI 59 protection?
- What is the difference between ANSI 59 and ANSI 24?
- Why is undervoltage protection important for motors?
- Can undervoltage protection trip during motor starting?
- What is residual overvoltage protection?
- Does every GE Multilin relay support ANSI 27 and ANSI 59?
- How are overvoltage and undervoltage protection tested?
- Conclusion
1. Introduction
Overvoltage and undervoltage protection are important functions in electrical power systems. They protect generators, transformers, motors, feeders, and other equipment against abnormal voltage conditions that can cause insulation stress, overheating, unstable operation, or equipment malfunction.
Overvoltage protection (ANSI 59) detects voltage levels above an approved operating limit. Undervoltage protection (ANSI 27) detects voltage levels below an approved threshold.
GE Multilin protection relays may provide voltage protection as part of generator, transformer, motor, feeder, or universal protection applications. The available elements, measurement methods, setting ranges, and logic depend on the exact relay model and firmware.
This article explains ANSI 27 and ANSI 59 protection principles, voltage measurement, setting calculations, time delays, coordination, practical applications, configuration considerations, testing, and troubleshooting.
2. What Is Overvoltage Protection (ANSI 59)?
Overvoltage protection detects an increase in voltage above a configured threshold.
Excessive voltage can increase electrical stress on insulation and connected equipment.
Typical causes include:
- Sudden load rejection.
- Generator excitation problems.
- Incorrect voltage regulator operation.
- Transformer tap-changer malfunction.
- Ferranti effect on lightly loaded or unloaded transmission lines.
- Single-phase earth faults in certain unearthed or impedance-grounded networks.
- Incorrect system switching.
- Abnormal operating conditions in isolated networks.
The relay measures the relevant voltage quantity and compares it with the configured overvoltage threshold.
If the voltage exceeds the pickup level for the required operating time, the protection issues an alarm or trip command according to the configured logic.
3. What Is Undervoltage Protection (ANSI 27)?
Undervoltage protection detects a decrease in voltage below a configured threshold.
Undervoltage can affect the performance and stability of electrical equipment.
Typical causes include:
- Short circuits.
- System overload.
- Generator underexcitation or instability.
- Transformer or feeder faults.
- Voltage regulator malfunction.
- Loss of incoming supply.
- Large motor starting.
- Weak network conditions.
- System disturbances.
Undervoltage protection may be used for alarms, load shedding, motor protection, generator supervision, and supply-transfer schemes.
The protection engineer must distinguish between a genuine system undervoltage condition and a voltage measurement problem caused by VT circuit failure.
4. Voltage Protection Measurement Principles
The accuracy of voltage protection depends on correct voltage measurement and configuration.
The relay may receive voltage signals from:
- Phase-to-phase VT secondary circuits.
- Phase-to-neutral VT secondary circuits.
- Three-phase voltage transformer connections.
- Open-delta or broken-delta voltage circuits, where supported.
- Generator terminal voltage transformers.
- Busbar voltage transformers.
- Line-side voltage transformers.
The engineer must identify the measurement method supported by the specific relay.
4.1 Phase-to-neutral voltage
For a balanced three-phase system:
[
V_{LN}=\frac{V_{LL}}{\sqrt{3}}
]
Where:
- (V_{LN}) = phase-to-neutral voltage.
- (V_{LL}) = phase-to-phase voltage.
For a 33 kV system:
[
V_{LN}=\frac{33}{\sqrt{3}}
]
[
V_{LN}\approx19.05\text{ kV}
]
4.2 Voltage transformer ratio
Consider a voltage transformer with:
- Primary voltage: 33 kV.
- Secondary voltage: 110 V phase-to-phase.
The VT ratio is:
[
K_{VT}=\frac{33,000}{110}
]
[
K_{VT}=300
]
If the primary voltage is 30 kV, the corresponding secondary voltage is:
[
V_s=\frac{30,000}{300}
]
[
V_s=100\text{ V}
]
The relay must be configured with the correct VT ratio and voltage reference.
4.3 Phase voltage versus line voltage
An important engineering mistake is confusing phase-to-phase and phase-to-neutral voltage settings.
For example, a 110 V phase-to-phase VT secondary system has a phase-to-neutral voltage of approximately:
[
V_{LN}=\frac{110}{\sqrt{3}}=63.5\text{ V}
]
The relay setting must use the measurement quantity expected by the particular voltage protection element.
5. Overvoltage Protection Characteristics
ANSI 59 protection may use different operating characteristics depending on the relay model.
Typical arrangements include:
- Definite-time overvoltage.
- Multiple overvoltage stages.
- Instantaneous or short-delay voltage protection.
- Inverse-time characteristics, where supported.
- Phase-selective voltage elements.
- Positive-sequence voltage supervision.
- Residual or zero-sequence overvoltage elements.
Not every GE Multilin relay supports all these arrangements.
5.1 Definite-time overvoltage
A definite-time overvoltage element operates when voltage exceeds the pickup threshold continuously for the configured delay.
For example:
| Parameter | Illustrative setting |
|---|---|
| Voltage pickup | 1.10 pu |
| Time delay | 2 seconds |
If the measured voltage exceeds 1.10 pu for longer than the configured delay, the element operates.
5.2 Multiple overvoltage stages
Some protection schemes use two stages.
| Stage | Pickup | Delay | Typical purpose |
|---|---|---|---|
| 59-1 | 1.10 pu | 2 s | Alarm or delayed trip |
| 59-2 | 1.20 pu | 0.2 s | Faster protection |
These are illustrative values only. Actual settings must follow equipment limits and the approved protection study.
6. Undervoltage Protection Characteristics
Undervoltage protection can also use multiple stages and time delays.
Typical applications include:
- Alarm.
- Motor undervoltage protection.
- Load shedding.
- Automatic transfer schemes.
- Generator auxiliary supply supervision.
- Feeder disconnection.
- Voltage-dependent control logic.
6.1 Definite-time undervoltage
A definite-time undervoltage element operates when voltage remains below the pickup threshold for the configured delay.
Example:
| Parameter | Illustrative setting |
|---|---|
| Voltage threshold | 0.80 pu |
| Time delay | 3 seconds |
If the measured voltage falls below 0.80 pu for the required time, the element operates.
6.2 Multiple undervoltage stages
A two-stage arrangement may be used:
| Stage | Voltage threshold | Delay | Typical purpose |
|---|---|---|---|
| 27-1 | 0.90 pu | 5 s | Alarm or delayed response |
| 27-2 | 0.70 pu | 0.5 s | Faster disconnection |
The settings must account for normal voltage fluctuations, motor starting, system disturbances, and equipment ride-through requirements.
7. Per-Unit Voltage Calculations
Voltage protection settings are often expressed in per unit (pu).
The per-unit voltage is:
[
V_{pu}=\frac{V_{\text{measured}}}{V_{\text{base}}}
]
Where:
- (V_{\text{measured}}) is the measured voltage.
- (V_{\text{base}}) is the selected nominal voltage reference.
Example
Assume a 33 kV bus has an actual voltage of 30 kV.
[
V_{pu}=\frac{30}{33}
]
[
V_{pu}=0.909
]
The bus voltage is approximately 0.909 pu, or 90.9% of nominal voltage.
If an undervoltage threshold is 0.90 pu, this measured voltage is slightly above the threshold.
The engineer must use the correct voltage base and measurement convention for the relay element.
8. Generator Overvoltage Protection
Generator overvoltage protection is important because generator voltage is controlled by the excitation system.
Possible causes include:
- Automatic voltage regulator malfunction.
- Sudden load rejection.
- Incorrect excitation control.
- Field circuit problems.
- Islanded operation.
- System disturbances.
- Incorrect generator voltage reference.
Overvoltage can increase insulation stress in the generator stator and connected equipment.
A generator protection scheme may include multiple voltage stages with different delays.
Engineering considerations
The protection engineer should consider:
- Generator rated terminal voltage.
- Generator capability curve.
- Excitation system limits.
- Transformer voltage ratio.
- Generator operating modes.
- Load rejection characteristics.
- Manufacturer voltage withstand limits.
Overvoltage protection should be coordinated with the generator voltage regulator and excitation protection.
9. Generator Undervoltage Protection
Generator undervoltage protection may be used to detect abnormal terminal voltage and support generator protection logic.
Possible causes include:
- Excitation system failure.
- Severe system faults.
- Generator operating problems.
- Loss of excitation.
- Voltage transformer circuit failure.
- Abnormal islanded operation.
However, undervoltage protection must be coordinated carefully with other generator protection functions.
For example, loss of excitation protection (ANSI 40) is not equivalent to undervoltage protection. It detects a different electrical condition and may use impedance-based characteristics.
A voltage reduction alone should not automatically be interpreted as loss of excitation.
10. Transformer Overvoltage and Undervoltage Protection
Transformers are designed to operate within defined voltage and frequency limits.
Excessive voltage can increase core flux and magnetizing current.
The relationship between flux, voltage, and frequency is important.
For a transformer operating under approximately constant frequency:
[
B_{\max}\propto\frac{V}{f}
]
Where:
- (B_{\max}) is maximum core flux density.
- (V) is applied voltage.
- (f) is frequency.
An increase in voltage or decrease in frequency can increase core flux and lead to overexcitation.
This is why transformer overfluxing protection (ANSI 24) is different from simple overvoltage protection (ANSI 59).
Practical distinction
| Function | Main quantity |
|---|---|
| ANSI 59 | Voltage magnitude |
| ANSI 27 | Undervoltage magnitude |
| ANSI 24 | Voltage-to-frequency ratio or related overexcitation quantity |
The protection engineer should coordinate these elements according to transformer design limits.
11. Motor Undervoltage Protection
Undervoltage protection is particularly important for large induction motors.
A reduction in terminal voltage can affect motor torque and starting performance.
For an induction motor operating under simplified conditions, electromagnetic torque is approximately proportional to the square of voltage:
[
T\propto V^2
]
This relationship is an approximation under comparable operating conditions.
If voltage decreases to 80% of nominal:
[
T\approx(0.8)^2=0.64
]
The available torque may fall to approximately 64% of its nominal-voltage value under the simplified assumption.
Possible consequences include:
- Reduced acceleration torque.
- Increased motor starting time.
- Increased current during certain operating conditions.
- Stalling.
- Process disruption.
- Thermal stress.
Motor undervoltage protection should be coordinated with motor starting requirements, contactor behavior, process requirements, and the motor’s thermal protection.
GE Multilin motor protection relays such as 339, 369, 469, and 869 may provide voltage-related functions depending on model and firmware.
12. Feeder and Distribution Applications
Voltage protection is commonly used in distribution and industrial networks.
Typical applications include:
- Feeder undervoltage supervision.
- Bus undervoltage protection.
- Load shedding.
- Automatic transfer schemes.
- Voltage restoration logic.
- Capacitor-bank control.
- Generator interconnection supervision.
In distribution networks, undervoltage may be caused by overload, upstream faults, or loss of supply.
Overvoltage may occur during load rejection, incorrect voltage regulation, or abnormal network switching.
The protection engineer must coordinate voltage protection with network operating procedures and automatic control schemes.
13. Phase Undervoltage and Positive-Sequence Undervoltage
Voltage protection may be based on individual phase measurements or sequence quantities.
13.1 Phase undervoltage
Individual phase undervoltage elements monitor the voltage of each phase.
This can be useful for detecting phase-specific voltage problems.
13.2 Positive-sequence undervoltage
Positive-sequence voltage represents the balanced component of the three-phase voltage system.
It can be useful for detecting balanced system voltage reductions while reducing sensitivity to certain unbalanced conditions.
The choice depends on the application and the protection objective.
13.3 Negative-sequence voltage
Negative-sequence voltage can help identify voltage unbalance.
It is not equivalent to ordinary undervoltage protection.
The availability of phase, positive-sequence, and negative-sequence voltage elements must be verified for the exact GE Multilin relay.
14. Residual Overvoltage and Earth-Fault Detection
In certain network earthing arrangements, an earth fault produces a displacement of the neutral point and an increase in residual or zero-sequence voltage.
Residual overvoltage protection is often identified by ANSI 59N or a related designation, depending on the application and device implementation.
A common measurement arrangement uses an open-delta or broken-delta VT secondary circuit.
The residual voltage is related to:
[
3V_0=V_A+V_B+V_C
]
Where (V_0) is the zero-sequence voltage component.
This quantity can be used for earth-fault detection in suitable networks.
However, residual overvoltage protection is not identical to phase overvoltage protection. The VT connection, system grounding, and voltage measurement method must be considered.
15. Voltage Protection Settings and Coordination
Voltage protection settings must be selected according to the equipment’s operating limits and the system protection philosophy.
Important factors include:
- Nominal system voltage.
- Equipment insulation capability.
- Generator capability.
- Motor operating requirements.
- Transformer voltage and frequency limits.
- Normal voltage variation.
- Voltage regulator performance.
- System fault-clearing time.
- Automatic transfer and load-shedding schemes.
- Utility grid-code requirements.
15.1 Setting coordination
Voltage protection should not operate unnecessarily during normal system disturbances.
For example, motor starting can cause temporary voltage depression. If the undervoltage threshold and time delay are too sensitive, the relay may trip during an acceptable starting event.
Similarly, generator voltage regulators may produce temporary voltage deviations during load changes.
The protection engineer must coordinate the pickup and delay with the expected operating behavior.
16. Practical Calculation Example: 33 kV Bus Undervoltage
Consider a 33 kV bus with the following illustrative data:
| Parameter | Value |
|---|---|
| Nominal voltage | 33 kV |
| VT secondary voltage | 110 V |
| VT ratio | 300:1 |
| Undervoltage threshold | 0.85 pu |
| Time delay | 3 seconds |
Step 1 – Calculate the primary undervoltage threshold
[
V_{\text{pickup}}=33\times0.85
]
[
V_{\text{pickup}}=28.05\text{ kV}
]
Step 2 – Convert to secondary voltage
[
V_s=\frac{28.05}{300}
]
[
V_s=93.5\text{ V}
]
Therefore, if the relay measures 93.5 V on the corresponding 110 V voltage reference, it is at the illustrative 0.85 pu threshold.
Step 3 – Apply the time delay
If the voltage remains below the pickup threshold for 3 seconds, the element operates according to the configured definite-time characteristic.
The exact relay setting may be entered in volts, per unit, or percentage of nominal voltage depending on the model and software.
17. GE Multilin Voltage Protection Applications
GE Multilin provides protection relay families for generator, transformer, motor, feeder, and universal applications.
Relevant products may include:
- G60 and G30 generator protection relays.
- 889 generator protection relay.
- T60 transformer protection relay.
- 845 transformer protection relay.
- 339, 369, 469, and 869 motor protection relays.
- 350 and 850 feeder protection relays.
- UR family protection systems with applicable voltage elements.
The actual voltage protection functions differ across these devices.
Before engineering ANSI 27 or ANSI 59, verify:
- Available voltage inputs.
- Phase-to-phase or phase-to-neutral measurement.
- Supported voltage elements.
- Sequence voltage functions.
- Definite-time or inverse-time characteristics.
- Voltage supervision.
- Required firmware.
- Output and trip logic.
Do not assume that every model supports every voltage protection function listed in this article.
18. General GE Multilin Configuration Workflow
The following is a generic engineering workflow. Actual menus and setting names depend on the relay model and firmware.
Step 1 – Identify the relay
Record:
- Exact relay model.
- Product order code.
- Firmware version.
- Hardware configuration.
- Voltage input ratings.
- Engineering software version.
Step 2 – Verify VT configuration
Confirm:
- Primary VT voltage.
- Secondary VT voltage.
- VT ratio.
- Phase assignment.
- Phase sequence.
- Voltage connection type.
- Measurement reference.
Step 3 – Select the voltage protection element
Determine whether the application requires:
- Phase overvoltage.
- Phase undervoltage.
- Positive-sequence undervoltage.
- Negative-sequence voltage supervision.
- Residual overvoltage.
- Multiple-stage voltage protection.
Only select functions supported by the actual relay.
Step 4 – Calculate the settings
Determine:
- Pickup threshold.
- Operating delay.
- Reset or dropout behavior.
- Alarm threshold.
- Trip threshold.
- Coordination with other functions.
Step 5 – Configure trip and alarm logic
Possible outputs include:
- Voltage alarm.
- Generator trip.
- Motor trip.
- Feeder trip.
- Load-shedding initiation.
- Automatic transfer initiation.
- External control signal.
The final output mapping must follow the approved protection philosophy.
Step 6 – Verify settings
Before downloading:
- Check voltage scaling.
- Verify per-unit calculations.
- Confirm time delays.
- Review blocking logic.
- Verify trip destinations.
- Save the settings file and revision record.
19. Voltage Protection Testing and Commissioning
Voltage protection testing should verify measurement accuracy, pickup, dropout, time delay, phase selection, and trip logic.
19.1 Pre-test checks
Before testing:
- Verify the approved relay settings.
- Confirm relay model and firmware.
- Check VT ratios.
- Verify voltage input wiring.
- Confirm phase sequence.
- Review voltage measurement scaling.
- Check binary outputs and trip logic.
19.2 Overvoltage pickup test
- Apply nominal voltage to the relay.
- Confirm the measured voltage.
- Increase voltage gradually.
- Monitor the overvoltage element.
- Record the pickup value.
- Compare the result with the approved setting and relay tolerance.
19.3 Undervoltage pickup test
- Apply nominal voltage.
- Reduce the applied voltage gradually.
- Monitor the undervoltage element.
- Record the operating threshold.
- Compare the result with the configured setting.
19.4 Time-delay test
- Apply voltage above the overvoltage threshold or below the undervoltage threshold.
- Maintain the condition.
- Measure the operating time.
- Compare the result with the configured delay.
- Repeat for each enabled stage.
19.5 Dropout and reset test
Restore the voltage to the normal range.
Verify that:
- The protection element resets correctly.
- The alarm clears as expected.
- The trip logic behaves according to the configured latch and reset philosophy.
19.6 Phase-specific test
Where phase-selective voltage protection is used:
- Test phase A.
- Test phase B.
- Test phase C.
- Confirm correct phase identification.
- Verify the expected output logic.
19.7 Voltage supervision test
Where VT failure supervision is implemented:
- Simulate the approved voltage measurement failure condition.
- Verify the VT failure indication.
- Check the response of the voltage protection elements.
- Confirm that measurement failure does not create an unintended protection decision.
Testing should follow the manufacturer’s recommended procedure and the site’s approved commissioning safety arrangements.
20. Common Voltage Protection Problems
Problem 1 – Overvoltage protection operates during normal operation
Possible causes:
- Incorrect VT ratio.
- Incorrect voltage scaling.
- Incorrect nominal voltage setting.
- Pickup too low.
- Incorrect phase measurement.
- VT connection problem.
Recommended checks:
- Verify primary and secondary VT ratings.
- Compare relay measurements with calibrated equipment.
- Review the pickup setting.
- Inspect voltage wiring.
Problem 2 – Undervoltage protection operates during motor starting
Possible causes:
- Pickup too high.
- Time delay too short.
- Starting voltage dip not considered.
- Incorrect motor starting study.
- Incorrect voltage measurement.
Recommended checks:
- Review motor starting studies.
- Record actual voltage dip.
- Coordinate the undervoltage delay.
- Verify motor thermal and starting protection.
Problem 3 – Voltage protection does not operate
Possible causes:
- Function disabled.
- Incorrect voltage input assignment.
- Incorrect setting reference.
- Blocking signal active.
- Wrong voltage measurement type.
- Incorrect trip output mapping.
Recommended checks:
- Monitor measured voltage.
- Verify the element enable status.
- Check the configured voltage reference.
- Review the logic and output matrix.
Problem 4 – Incorrect phase undervoltage indication
Possible causes:
- Incorrect phase assignment.
- VT wiring error.
- Wrong phase sequence.
- Incorrect voltage input mapping.
Recommended checks:
- Verify phase-to-phase and phase-to-neutral connections.
- Compare all three phase measurements.
- Inspect the VT secondary circuits.
Problem 5 – False undervoltage caused by VT failure
Possible causes:
- Blown VT fuse.
- Open secondary wiring.
- VT circuit isolation.
- Incorrect voltage supervision.
Recommended checks:
- Inspect the VT circuit.
- Check VT failure alarms.
- Review voltage measurement quality.
- Verify the scheme’s response to invalid measurements.
21. Voltage Protection Commissioning Checklist
| No. | Inspection or test | Result |
|---|---|---|
| 1 | Verify relay model and firmware | ☐ |
| 2 | Confirm voltage protection availability | ☐ |
| 3 | Verify VT primary rating | ☐ |
| 4 | Verify VT secondary rating | ☐ |
| 5 | Confirm VT ratio | ☐ |
| 6 | Check voltage input wiring | ☐ |
| 7 | Verify phase sequence | ☐ |
| 8 | Confirm nominal voltage reference | ☐ |
| 9 | Test overvoltage pickup | ☐ |
| 10 | Test undervoltage pickup | ☐ |
| 11 | Test operating time delay | ☐ |
| 12 | Verify dropout and reset | ☐ |
| 13 | Test all enabled phases | ☐ |
| 14 | Check VT failure supervision | ☐ |
| 15 | Verify alarm logic | ☐ |
| 16 | Verify trip logic | ☐ |
| 17 | Check event records | ☐ |
| 18 | Confirm final approved settings | ☐ |
| 19 | Save configuration backup | ☐ |
| 20 | Complete commissioning report | ☐ |
22. Best Engineering Practices
For reliable voltage protection:
- Confirm the correct voltage measurement reference.
- Verify VT ratio, phase sequence, and wiring.
- Distinguish phase voltage from line voltage.
- Calculate settings in per unit before entering relay values.
- Coordinate voltage thresholds with equipment operating limits.
- Consider motor starting and temporary system disturbances.
- Coordinate transformer overvoltage protection with ANSI 24 overexcitation protection.
- Use appropriate VT failure supervision.
- Verify the complete alarm and trip logic.
- Test all enabled stages during commissioning.
Voltage protection should be engineered as part of the complete equipment protection and system-control philosophy, not as an isolated relay function.
23. Training on GE Multilin Protection Relays by Elec-Engg
Practical voltage protection engineering requires a clear understanding of VT circuits, voltage measurement, per-unit calculations, generator and transformer operating limits, motor starting, relay settings, and commissioning procedures.
Elec-Engg provides practical technical training by Dr Saeed Roostaee (Electrical Engineering) for engineers involved in power-system protection, relay configuration, commissioning, operation, and maintenance.
Relevant training subjects include:
- GE Multilin protection relay families.
- Generator protection using G60, G30, and 889.
- Transformer protection using T60 and 845.
- Motor protection using 339, 369, 469, and 869.
- Overvoltage and undervoltage protection (ANSI 59/27).
- Overexcitation protection (ANSI 24).
- CT and VT configuration.
- EnerVista settings and configuration.
- Secondary injection and functional testing.
- Protection coordination and troubleshooting.
Training delivery options include:
- Pre-recorded technical video courses.
- Structured self-paced training.
- Live online training.
- Face-to-face technical training.
- Customized in-house training for companies and utilities.
Visit Elec-Engg to explore available courses or contact us to discuss a customized training requirement.
24. Frequently Asked Questions
What is ANSI 27 protection?
ANSI 27 is undervoltage protection. It detects voltage below a configured threshold and operates according to the selected time characteristic and logic.
What is ANSI 59 protection?
ANSI 59 is overvoltage protection. It detects voltage above a configured threshold and can initiate an alarm or trip.
What is the difference between ANSI 59 and ANSI 24?
ANSI 59 detects excessive voltage magnitude. ANSI 24 detects overexcitation, generally associated with an excessive voltage-to-frequency ratio.
Why is undervoltage protection important for motors?
Low voltage can reduce motor torque and affect acceleration and stable operation. Properly coordinated undervoltage protection helps prevent prolonged abnormal operating conditions.
Can undervoltage protection trip during motor starting?
Yes, if the settings are too sensitive or the delay is too short. The settings must be coordinated with the expected starting voltage dip and motor requirements.
What is residual overvoltage protection?
Residual overvoltage protection detects zero-sequence voltage associated with certain earth faults, particularly in suitable unearthed or impedance-grounded network arrangements.
Does every GE Multilin relay support ANSI 27 and ANSI 59?
No. Function availability and measurement options depend on the specific relay model, hardware, and firmware.
How are overvoltage and undervoltage protection tested?
They are tested using secondary voltage injection. The engineer verifies measurement accuracy, pickup thresholds, time delays, dropout behavior, phase selection, and trip logic.
Conclusion
Overvoltage and undervoltage protection are essential for protecting electrical equipment against abnormal voltage conditions. ANSI 59 detects excessive voltage, while ANSI 27 detects insufficient voltage.
Correct implementation requires accurate VT configuration, suitable pickup and time-delay settings, coordination with equipment operating limits, and reliable integration with protection and control logic.
For GE Multilin applications, engineers should verify the actual voltage elements and measurement capabilities available in the selected relay model and firmware before finalizing the protection design.
