ABB REB670 Busbar Protection Relay – Complete Technical Guide
- 1. Introduction to ABB REB670
- 2. What Is Busbar Protection?
- 3. Operating Principle of Busbar Differential Protection
- 4. Low-Impedance Busbar Differential Protection in REB670
- 5. Main Busbar Differential Protection Function
- 6. Busbar Protection Zones
- 7. Busbar Replica and Zone Selection
- 8. Check-Zone Differential Protection
- 9. Sensitive Differential Protection
- 10. CT Saturation and Differential Protection Stability
- 11. Open CT Detection and CT Circuit Supervision
- 12. Busbar Protection Trip Logic
- 13. Circuit-Breaker Failure Protection
- 14. Backup Protection Functions
- 15. REB670 and Different Substation Busbar Arrangements
- 16. PCM600 Configuration and Engineering
- 17. IEC 61850 Communication in REB670
- 18. Testing and Commissioning of REB670
- 19. Common REB670 Problems and Troubleshooting
- 20. REB670 vs REB650 – Main Differences
- 21. Frequently Asked Questions About ABB REB670
- What is ABB REB670 used for?
- Is REB670 a low-impedance or high-impedance relay?
- What is the main protection function of REB670?
- Does REB670 support double-busbar protection?
- What is the purpose of the check zone?
- Why is CT saturation important in busbar protection?
- Does REB670 include open CT detection?
- Which software is used to configure REB670?
- Does REB670 support IEC 61850?
- Can REB670 be tested using OMICRON?
- 22. Conclusion
- Related Articles
1. Introduction to ABB REB670
The ABB REB670 is a numerical busbar protection and control IED from the ABB Relion 670 series. It is designed to provide fast, selective and reliable protection for busbar systems in high-voltage and extra-high-voltage substations.
Busbars are critical components of electrical substations. They connect incoming transmission lines, transformers, generators, bus couplers and outgoing feeders. A fault on a busbar can affect several circuits simultaneously and may result in severe equipment damage and widespread power-system disturbances.
For this reason, busbar protection must operate rapidly and selectively.
The REB670 uses low-impedance differential protection technology. It measures the currents connected to the protected busbar zones and determines whether a fault is internal or external.
Main capabilities include:
- Low-impedance busbar differential protection
- Multiple busbar protection zones
- Busbar zone selection
- Check-zone differential protection
- Sensitive differential protection
- CT circuit supervision
- Open CT detection
- Stability during external faults and CT saturation
- Circuit-breaker failure protection
- Backup overcurrent protection
- Disturbance recording and event monitoring
- IEC 61850 communication
- Integration with substation automation systems
The available functions and number of bays depend on the selected REB670 configuration, hardware and product version.
2. What Is Busbar Protection?
A busbar is a common electrical connection point that distributes power between different circuits in a substation.
Typical busbar-connected equipment includes:
- Incoming transmission lines
- Outgoing transmission lines
- Power transformers
- Bus couplers
- Bus section breakers
- Busbar disconnectors
- Generator connections
- Capacitor banks and reactors
A busbar fault is particularly serious because multiple circuits may contribute fault current to the same fault location.
For example, consider a double-busbar substation with two bus sections and several incoming and outgoing feeders.
If a short circuit occurs on Busbar 1, the protection system should disconnect only the circuit-breakers connected to the faulty busbar zone while keeping the healthy busbar section in service whenever the switching arrangement permits.
This is the main objective of busbar differential protection.
3. Operating Principle of Busbar Differential Protection
The REB670 operates according to the differential protection principle.
The current entering and leaving a protected busbar zone should be approximately equal under normal operating conditions and during external faults.
Using Kirchhoff’s Current Law:
[
\sum I_{\text{in}}-\sum I_{\text{out}}=0
]
For an internal fault, the current balance is disturbed and a differential current appears.
The basic differential current can be represented as:
[
I_d=\left|\sum I_k\right|
]
Where:
- (I_d) is the differential current
- (I_k) represents the measured current contributions from the connected circuits
The relay also evaluates a restraint or stabilizing quantity to maintain security during external faults.
3.1 Normal operating condition
During normal operation, the sum of currents entering and leaving the busbar zone is approximately zero.
The differential current remains below the operating threshold, and the relay does not trip.
3.2 External fault
Consider a short circuit on an outgoing feeder outside the protected busbar zone.
The fault current enters the busbar through one or more incoming circuits and leaves through the faulted feeder.
Ideally, the sum of all measured currents remains balanced.
The differential protection must remain stable even when high fault currents cause CT saturation.
3.3 Internal busbar fault
If a fault occurs inside the protected busbar zone, the current contributions from the connected circuits flow toward the fault.
The differential current increases and the protection operates when its operating criteria are satisfied.
The relay then issues trip commands to the circuit-breakers associated with the faulty zone.
4. Low-Impedance Busbar Differential Protection in REB670
The REB670 is a low-impedance busbar differential protection IED.
This is an important distinction when comparing it with traditional high-impedance busbar differential schemes.
In a low-impedance scheme, the relay receives individual current measurements from the connected circuits and performs the differential calculation internally.
The CT ratios can be adapted through the relay configuration, allowing different CT ratios to be used within the protected busbar arrangement, subject to the applicable engineering requirements.
Main advantages of low-impedance differential protection
- Flexible application for different busbar arrangements
- CT ratio adaptation
- Multiple differential protection zones
- Integrated zone selection logic
- Check-zone supervision
- Sensitive differential protection
- CT saturation stabilization
- Integrated supervision and monitoring
The REB670 uses percentage-restraint stabilization based on the established RADSS principle, with additional stabilization intended to improve security during severe CT saturation.
5. Main Busbar Differential Protection Function
The main protection function is:
87B – Busbar Differential Protection
The REB670 product documentation identifies busbar differential protection functions using IEC 61850 function blocks including:
- BCZPDIF
- BZNPDIF
- BUSPTRC
- BZITGGIO
- BZNSPDIF
- BCZSPDIF
The exact combination depends on the selected product configuration and application.
The main differential protection algorithm evaluates the current contributions from the circuits assigned to each protected zone.
It can operate selectively for internal faults and remain stable for external faults when the CT inputs and application are correctly engineered.
6. Busbar Protection Zones
Modern substations may have several busbar sections and different switching arrangements.
The REB670 supports multiple differential protection zones, depending on the selected configuration.
Examples include:
- Single busbar
- Single busbar with bus section breaker
- Double busbar with bus coupler
- Double busbar with transfer bus
- One-and-a-half circuit-breaker arrangement
- Ring bus arrangement
- Mesh bus arrangement
The relay must determine which circuit-breakers and CT measurements belong to each protection zone.
6.1 Single busbar
A single-busbar arrangement is relatively simple.
All connected circuits are connected to the same busbar, and the differential protection zone includes the relevant circuit CTs.
For an internal busbar fault, all circuit-breakers connected to that busbar must be tripped.
6.2 Single busbar with bus section breaker
A bus section breaker divides the busbar into two sections.
Each section can be protected as a separate differential zone.
If a fault occurs on one section, the protection should isolate that section while maintaining the healthy section in service where possible.
6.3 Double busbar with bus coupler
In a double-busbar substation, circuits can be connected to either Busbar 1 or Busbar 2 through disconnectors.
The busbar protection must continuously determine the electrical connection of each circuit.
For example:
- A feeder connected to Busbar 1 belongs to Zone 1.
- A feeder connected to Busbar 2 belongs to Zone 2.
- A feeder transferred from Busbar 1 to Busbar 2 must be reassigned to the correct protection zone.
The REB670 uses the busbar replica and zone-selection logic to achieve this.
6.4 One-and-a-half circuit-breaker arrangement
In a one-and-a-half breaker arrangement, two circuits share three circuit-breakers in a diameter.
The busbar protection must correctly identify the relevant busbar zones and the switching status of the disconnectors.
The protection design must also consider the role of the middle circuit-breaker and the required breaker-failure protection.
6.5 Ring and mesh bus arrangements
Ring and mesh bus substations require careful zone selection because several switching devices and electrical paths are involved.
The protection scheme must correctly identify which CTs belong to each protected zone under different switching conditions.
The REB670 product guide provides typical application arrangements and configuration guidance.
7. Busbar Replica and Zone Selection
The busbar replica represents the actual electrical connection of circuits to the busbar sections.
The relay uses the status of disconnectors and circuit-breakers to determine which current inputs belong to each differential protection zone.
Typical status signals include:
- Busbar disconnector 1 open/closed
- Busbar disconnector 2 open/closed
- Bus coupler status
- Bus section breaker status
- Circuit-breaker status
- Isolator supervision signals
Why is zone selection important?
Consider a feeder that can be connected to either Busbar 1 or Busbar 2.
If the feeder is physically connected to Busbar 2 but the protection system incorrectly assigns its CT current to Busbar 1, the differential calculation may become incorrect.
This can result in unwanted tripping or failure to detect an internal fault.
Therefore, correct disconnector status wiring and busbar replica configuration are essential.
Disconnector supervision
The relay should supervise the auxiliary contacts used for busbar zone selection.
The application may use one or two auxiliary contacts to determine the open and closed states.
Where two contacts are used, their consistency and transition behaviour can provide additional supervision.
The correct logic must reflect the actual disconnector mechanism and auxiliary contact arrangement.
8. Check-Zone Differential Protection
The check zone is an additional differential protection calculation that provides independent supervision of the main busbar zone selection.
It helps improve the security of the overall busbar protection scheme.
The main differential protection zones depend on the busbar replica and disconnector position information.
The check zone provides an additional system-wide differential criterion.
Why is a check zone important?
Consider an incorrect disconnector position signal.
The main zone selection may incorrectly assign a feeder to a busbar zone.
This could affect the differential calculation.
The check zone provides additional supervision and helps prevent unwanted operation caused by certain zone-selection errors.
The check-zone arrangement must be engineered according to the busbar configuration and the ABB application guidance.
9. Sensitive Differential Protection
The REB670 includes sensitive differential protection functionality.
This feature can be useful in applications where internal earth faults produce relatively low fault currents.
For example, in low-impedance-earthed systems, the earth-fault current may be limited by a neutral grounding resistor or reactor.
A conventional differential operating threshold may not provide the required sensitivity for every application.
The sensitive differential level can be configured to detect these internal faults.
Important engineering considerations
- Minimum differential current
- Operating delay
- External enabling signal
- Neutral grounding arrangement
- Expected minimum internal fault current
- CT measurement accuracy
- Security during external faults
For increased security, ABB’s application documentation describes external enabling of the sensitive differential function, for example using a suitable external earth-fault detection signal.
The sensitive function must be engineered carefully to avoid unwanted operation.
10. CT Saturation and Differential Protection Stability
CT saturation is one of the most important challenges in busbar differential protection.
During a severe external fault, the fault current can be very high.
If one CT saturates more than the others, its secondary current may no longer accurately represent the primary current.
This creates an artificial differential current.
Without suitable stabilization, the differential protection could incorrectly identify an external fault as an internal fault.
REB670 CT saturation stabilization
The REB670 uses percentage-restraint stabilization based on the RADSS principle, with additional stabilization for severe CT saturation.
The product documentation describes the stability of the protection during external faults, including conditions involving heavy CT saturation.
CT engineering requirements
The protection engineer should verify:
- CT ratio
- CT accuracy class
- CT secondary winding resistance
- CT lead resistance
- CT burden
- Maximum external fault current
- CT remanence characteristics
- CT transient performance
All CTs connected to a differential zone must be assessed as part of the same protection study.
The CT selection should satisfy the requirements of the applicable ABB application documentation and relevant standards.
11. Open CT Detection and CT Circuit Supervision
An open CT secondary circuit can cause incorrect current measurements and may create a dangerous condition.
The REB670 includes open CT detection and supervision features.
The relay can identify certain abnormal CT measurement conditions and provide alarms or configured blocking actions.
Important functions and engineering considerations include:
- Open CT detection
- CT circuit supervision
- Differential protection blocking logic
- Alarm generation
- External fault conditions
- CT circuit wiring and terminal inspection
The response to an open CT condition must be selected according to the protection philosophy.
The engineer should not assume that every CT supervision alarm automatically blocks all differential zones. The actual logic and settings must be verified.
12. Busbar Protection Trip Logic
When the differential protection detects an internal fault, the relay must issue trip commands to the circuit-breakers connected to the faulty busbar zone.
The trip logic should be selective.
For example, if a fault occurs on Busbar 1, the protection should trip the breakers associated with Busbar 1 without unnecessarily disconnecting Busbar 2.
The trip logic normally includes:
- Differential protection start
- Differential protection operate
- Check-zone supervision, where configured
- Zone selection
- Circuit-breaker trip output
- Trip latching or reset logic
- Breaker-failure initiation
- Disturbance recording
The complete trip matrix must be reviewed during engineering and commissioning.
13. Circuit-Breaker Failure Protection
The REB670 can provide circuit-breaker failure protection as part of the overall busbar protection application.
The main function is:
CCRBRF – Circuit-Breaker Failure Protection
A breaker-failure condition occurs when a circuit-breaker does not interrupt the fault current after receiving a trip command.
The protection supervises the trip command and current conditions.
If the breaker fails to clear the fault within the configured time, backup tripping is initiated.
Typical breaker-failure sequence
- Busbar differential protection detects an internal fault.
- The relay issues a trip command to the relevant circuit-breaker.
- The breaker receives the trip command.
- Current supervision checks whether the fault current has been interrupted.
- If current remains after the configured time, breaker-failure protection operates.
- The backup trip logic disconnects the required surrounding breakers.
Important settings include:
- Breaker-failure current threshold
- Initiation logic
- Retrip time
- Backup trip time
- Breaker auxiliary contact supervision
- Reset conditions
The actual breaker-failure arrangement depends on the substation design and the number of circuit-breakers involved.
14. Backup Protection Functions
In addition to busbar differential protection, the REB670 can provide several backup protection functions depending on configuration.
Examples include:
| Function | Application |
|---|---|
| OC4PTOC | Four-step phase overcurrent protection |
| PH4SPTOC | Four-step single-phase overcurrent protection |
| EF4PTOC | Four-step residual overcurrent protection |
| NS4PTOC | Negative-sequence overcurrent protection |
| TRPTTR | Thermal overload protection |
| CCRBRF | Circuit-breaker failure protection |
| UV2PTUV | Two-step undervoltage protection |
| OV2PTOV | Two-step overvoltage protection |
| ROV2PTOV | Residual overvoltage protection |
| SAPTUF | Underfrequency protection |
| SAPTOF | Overfrequency protection |
| SAPFRC | Rate-of-change-of-frequency protection |
The availability and number of function instances depend on the selected REB670 configuration.
15. REB670 and Different Substation Busbar Arrangements
The protection engineer must select a suitable REB670 arrangement based on the actual substation single-line diagram.
Single busbar
The protection zone includes the CTs of all circuits connected to the busbar.
Double busbar
The protection system must dynamically assign circuits to the correct busbar zone according to disconnector positions.
Double busbar with transfer bus
The protection design must include the transfer bus and associated switching equipment in the zone-selection and trip logic.
One-and-a-half breaker arrangement
The protection must consider the busbar zones, breaker arrangement and circuit assignments for each diameter.
Ring bus
The protection must account for the electrical connections and switching conditions around the ring.
A typical engineering study should include the single-line diagram, CT locations, circuit-breaker positions, disconnector status contacts, trip matrix and busbar protection zone definitions.
16. PCM600 Configuration and Engineering
ABB PCM600 – Protection and Control IED Manager is used for engineering and configuration of compatible REB670 IEDs.
Typical engineering activities include:
- Create a new PCM600 project.
- Add the REB670 IED.
- Select the correct product version and connectivity package.
- Verify the installed hardware.
- Configure current input channels.
- Enter CT ratios.
- Configure busbar differential protection.
- Configure the busbar replica.
- Configure disconnector and circuit-breaker status signals.
- Configure differential protection zones.
- Configure the check zone.
- Configure sensitive differential protection, if required.
- Configure open CT detection and supervision.
- Configure circuit-breaker failure protection.
- Configure trip logic and output contacts.
- Configure IEC 61850 communication.
- Validate the application.
- Download and verify the configuration.
Application configuration
The application configuration connects the protection functions to the actual binary inputs, binary outputs and internal logic signals.
Examples include:
- CT measurement inputs
- Disconnector position signals
- Circuit-breaker position signals
- Busbar zone selection
- Differential protection start signals
- Differential protection trip signals
- Check-zone signals
- Circuit-breaker failure initiation
- Trip output contacts
A correct application configuration is essential for reliable operation.
17. IEC 61850 Communication in REB670
The REB670 supports IEC 61850-based substation automation integration, subject to the installed product version and communication configuration.
Typical communication applications include:
- MMS monitoring and control
- GOOSE communication
- SCL configuration
- Protection status reporting
- Alarm and event reporting
- Circuit-breaker status exchange
- Integration with station-level SCADA
17.1 IEC 61850 MMS
MMS communication is commonly used for monitoring and control between the protection IED and the station-level system.
Typical information includes:
- Busbar differential protection start
- Busbar differential protection trip
- Differential zone status
- Circuit-breaker status
- Disconnector status
- CT supervision alarms
- Relay self-supervision alarms
- Measurement values
17.2 IEC 61850 GOOSE
GOOSE communication can be used for fast peer-to-peer communication between protection and control IEDs.
Possible applications include:
- Interlocking
- Circuit-breaker status exchange
- Direct protection signals
- Breaker-failure-related signals
- Trip-related applications
- Exchange of protection indications
The actual use of GOOSE depends on the station architecture and engineering configuration.
17.3 SCL engineering
SCL files are used to exchange IEC 61850 engineering information.
A typical workflow includes:
- Configure the REB670 in PCM600.
- Define the required IEC 61850 data.
- Export the relevant SCL file.
- Integrate the IED into the station configuration.
- Configure GOOSE publishers and subscribers.
- Import the updated configuration as required.
- Verify communication and signal mapping.
- Test the complete application.
18. Testing and Commissioning of REB670
Busbar protection testing requires particular care because incorrect operation can disconnect several substation circuits.
Testing should include individual protection functions, busbar replica logic, CT circuits, trip matrices and the complete protection scheme.
18.1 Visual and wiring inspection
Before testing, verify:
- Relay model and ordering information
- Auxiliary DC supply
- CT secondary wiring
- CT polarity
- CT ratios
- Binary input wiring
- Binary output wiring
- Circuit-breaker trip circuits
- Disconnector status signals
- Circuit-breaker auxiliary contacts
- Communication connections
- Panel earthing
18.2 Current measurement tests
Apply suitable secondary current signals and verify:
- Current magnitude
- Phase angle
- Phase identification
- CT ratio scaling
- Current direction
- Measurement consistency
18.3 Differential protection testing
A suitable OMICRON CMC test set can be used for differential protection testing.
Typical tests include:
- Differential operating threshold
- Differential operating characteristic
- Restraint characteristic
- Internal fault operation
- External fault stability
- CT saturation stability tests
- Sensitive differential protection
- Check-zone operation
- Trip output operation
The test engineer should verify both the operating and restraint regions.
18.4 Busbar replica testing
This is one of the most important parts of REB670 commissioning.
Verify the status of every disconnector and circuit-breaker used by the busbar replica.
Typical tests include:
- Busbar disconnector 1 open
- Busbar disconnector 1 closed
- Busbar disconnector 2 open
- Busbar disconnector 2 closed
- Bus coupler open
- Bus coupler closed
- Bus section breaker open
- Bus section breaker closed
- Transfer between busbar zones
- Disconnector status inconsistency
Confirm that the current inputs are assigned to the correct differential protection zones under each switching condition.
18.5 Check-zone testing
Verify the check-zone differential calculation and its relationship with the main differential protection zones.
The commissioning engineer should confirm the intended operation for internal and external faults and test the relevant supervision logic.
18.6 Circuit-breaker failure testing
Verify:
- Breaker-failure initiation
- Current detection
- Retrip logic
- Backup trip delay
- Backup trip outputs
- Reset conditions
18.7 IEC 61850 testing
Verify:
- MMS communication
- GOOSE publishing
- GOOSE subscription
- Signal mapping
- Communication supervision
- Quality indications
- Correct operation of the connected application logic
19. Common REB670 Problems and Troubleshooting
Problem 1: Unwanted busbar differential operation
Possible causes:
- Incorrect CT polarity
- Incorrect CT ratio
- Incorrect current input assignment
- Incorrect busbar replica
- Incorrect disconnector status
- CT saturation
- Wiring errors
Recommended checks: review current measurements, CT polarity, zone selection and the differential restraint measurements.
Problem 2: Busbar differential protection does not operate
Possible causes:
- Incorrect differential settings
- Incorrect CT connections
- Incorrect zone selection
- Incorrect trip logic
- Missing binary input signals
- Differential protection blocked by configured logic
Recommended checks: review the internal fault test results, differential operating signals and the complete trip path.
Problem 3: Incorrect busbar zone selection
Possible causes:
- Incorrect disconnector auxiliary contacts
- Incorrect binary input assignment
- Incorrect busbar replica logic
- Incorrect application configuration
- Faulty or inconsistent position indication
Recommended checks: test every switching position and compare the relay’s internal zone status with the actual single-line arrangement.
Problem 4: CT supervision alarm
Possible causes:
- Open CT secondary circuit
- Incorrect CT wiring
- Loose terminal connections
- Incorrect phase current measurement
- CT circuit problems
Recommended checks: inspect the CT secondary circuits and verify the current measurements.
Problem 5: Breaker-failure protection does not operate
Possible causes:
- Incorrect breaker-failure initiation
- Incorrect current threshold
- Incorrect time delay
- Incorrect breaker auxiliary contacts
- Missing backup trip connection
Recommended checks: test the complete breaker-failure sequence, including the external trip outputs.

20. REB670 vs REB650 – Main Differences
ABB has offered different busbar protection products for different substation applications.
The REB670 is positioned as an advanced busbar protection IED with flexible configurations for complex busbar arrangements.
The REB650 is another busbar protection product in the Relion 650 family. Its suitability depends on the required application, configuration and product availability.
| Feature | REB670 | REB650 |
|---|---|---|
| Main application | Busbar protection | Busbar protection |
| Protection principle | Low-impedance differential | Check the relevant product version |
| Busbar zone selection | Supported | Check configuration |
| Check-zone functionality | Documented | Check configuration |
| Complex busbar arrangements | Flexible application configurations | Depends on product capabilities |
| CT supervision | Available functions depend on configuration | Check product guide |
| IEC 61850 | Supported | Depends on product version |
| Engineering software | PCM600 | PCM600 |
Always compare the exact product guides and application manuals before selecting a relay for a project.
21. Frequently Asked Questions About ABB REB670
What is ABB REB670 used for?
ABB REB670 is a numerical busbar protection IED designed to detect and selectively isolate internal faults in busbar systems.
Is REB670 a low-impedance or high-impedance relay?
REB670 is a low-impedance busbar differential protection relay. It is not a conventional high-impedance differential protection scheme.
What is the main protection function of REB670?
Its main protection function is busbar differential protection, using current measurements from the circuits connected to the protected busbar zones.
Does REB670 support double-busbar protection?
Yes. The REB670 product guide describes applications for double-busbar substations, including busbar zone selection.
What is the purpose of the check zone?
The check zone provides additional differential supervision of the busbar protection system and helps improve security against incorrect zone selection.
Why is CT saturation important in busbar protection?
During an external fault, CT saturation can create an artificial differential current. The protection must remain stable under these conditions to avoid unwanted tripping.
Does REB670 include open CT detection?
Yes. The product documentation describes open CT detection and supervision functions.
Which software is used to configure REB670?
ABB PCM600 is used for engineering and configuration of compatible REB670 IEDs.
Does REB670 support IEC 61850?
Yes. REB670 supports IEC 61850-based substation integration, subject to the installed product version and configuration.
Can REB670 be tested using OMICRON?
Yes. Suitable OMICRON CMC test equipment can be used for differential protection testing, CT circuit verification, logic testing and commissioning.
22. Conclusion
The ABB REB670 is an advanced low-impedance busbar differential protection IED designed for reliable protection of complex substation busbar arrangements.
Its main capabilities include multiple differential protection zones, busbar replica and zone selection, check-zone supervision, sensitive differential protection, CT saturation stabilization and open CT supervision.
Correct engineering of the busbar replica, CT circuits, differential protection settings and trip logic is essential for reliable operation.
For protection and commissioning engineers, practical knowledge of REB670 is particularly important when working with double-busbar substations, bus couplers, bus section breakers and one-and-a-half breaker arrangements.
Elec-Engg – Practical Power System Protection and Substation Automation Training
Explore more technical articles and training resources covering ABB protection relays, busbar protection, PCM600, IEC 61850 and relay testing.
Related Articles
- ABB REG670 Generator Protection Relay
- ABB RET670 Transformer Protection Relay
- ABB RED670 Line Differential Protection Relay
- ABB REL670 Distance Protection Relay
- ABB REL650 Line Distance Protection Relay
- ABB PCM600 Engineering Software – Complete Guide
- Busbar Differential Protection – Operating Principle and Settings
- CT Saturation and Stability in Busbar Protection
- IEC 61850 Communication in Protection Relays

