- 1. Introduction to ABB REG650
- 2. Generator Protection Applications
- 3. REG650 Generator Protection System Architecture
- 4. Main Protection Functions of REG650
- 5. Generator Differential Protection – GENPDIF
- 6. Stator Earth-Fault Protection
- 7. Rotor Earth-Fault Protection
- 8. Loss-of-Excitation Protection
- 9. Overexcitation Protection – OEXPVPH
- 10. Negative-Sequence Overcurrent Protection – NS2PTOC
- 11. Voltage-Restrained Overcurrent Protection – VR2PVOC
- 12. Directional and Non-Directional Overcurrent Protection
- 13. Reverse Power Protection – GUPPDUP
- 14. Overpower Protection – GOPPDOP
- 15. Accidental Energisation Protection – AEGGAPC
- 16. Overvoltage and Undervoltage Protection
- 17. Frequency Protection
- 18. Thermal Overload Protection – TRPTTR
- 19. Breaker Failure Protection – CCRBRF
- 20. Pole Discordance Protection – CCRPLD
- 21. Generator Step-Up Transformer Protection
- 22. REG650 Application Configurations
- 23. Hardware Architecture
- 24. PCM600 Engineering and Configuration
- 25. IEC 61850 Communication
- 26. Commissioning and Testing of REG650
- 26.1 Visual Inspection
- 26.2 CT Circuit Testing
- 26.3 VT Circuit Testing
- 26.4 Differential Protection Testing
- 26.5 Overcurrent Protection Testing
- 26.6 Negative-Sequence Protection Testing
- 26.7 Voltage and Frequency Protection Testing
- 26.8 Reverse-Power Protection Testing
- 26.9 Binary Input and Output Testing
- 26.10 IEC 61850 Testing
- 26.11 Disturbance Recorder Testing
- 27. Common REG650 Problems and Troubleshooting
- Problem 1: Generator Differential Protection Trips During Normal Operation
- Problem 2: Earth-Fault Protection Does Not Operate
- Problem 3: Reverse-Power Protection Operates Incorrectly
- Problem 4: Negative-Sequence Protection Operates During Normal Operation
- Problem 5: IEC 61850 Communication Failure
- Problem 6: PCM600 Cannot Connect to REG650
- 28. REG650 Compared with REG670
- 29. Frequently Asked Questions
- What is ABB REG650?
- What generators can REG650 protect?
- Does REG650 support generator differential protection?
- Does REG650 support transformer differential protection?
- Does REG650 provide 100% stator earth-fault protection?
- Does REG650 support rotor earth-fault protection?
- Which software is used to configure REG650?
- Does REG650 support IEC 61850?
- Can REG650 protect the generator step-up transformer?
- What is the difference between REG650 and REG670?
- 30. Conclusion
ABB REG650 Generator Protection Relay – Complete Technical Guide
1. Introduction to ABB REG650
The ABB REG650 is a generator protection and control Intelligent Electronic Device (IED) belonging to the Relion 650 series. It is designed to protect and monitor synchronous generators and associated equipment in power plants and industrial generation facilities.
REG650 is particularly suitable for small and medium-sized generators. Its applications include:
- Hydroelectric power plants
- Pumped-storage power plants
- Steam turbine generators
- Gas turbine generators
- Diesel generator sets
- Combined-cycle power plants
- Cogeneration plants
- Industrial power generation
- Renewable energy generation facilities
The relay provides generator protection, backup protection, monitoring, measurement and control functions in one IED.
Depending on the ordered configuration, REG650 can provide generator differential protection, transformer differential protection, stator earth-fault protection, negative-sequence protection, loss-of-excitation protection, overexcitation protection, voltage protection, frequency protection and other generator protection functions.
One important characteristic of the Relion 650 series is its predefined application configurations. These provide engineers with ready-made functional arrangements that can reduce engineering effort during project implementation.
ABB PCM600 is used for engineering, parameterisation, application configuration and communication configuration.
2. Generator Protection Applications
A synchronous generator is exposed to several types of electrical and mechanical abnormal operating conditions.
These include:
- Phase-to-phase stator faults
- Stator earth faults
- Inter-turn faults
- Rotor earth faults
- Loss of excitation
- Unbalanced loading
- Reverse power
- Overload
- Overvoltage
- Undervoltage
- Overfrequency
- Underfrequency
- Overexcitation
- Accidental energisation
- Out-of-step operation
- Prime mover failure
The protection system must detect these conditions and initiate appropriate actions, such as generator circuit-breaker tripping, field breaker tripping, alarm generation or controlled shutdown.
REG650 can be configured to provide several of these protection functions in a single device. The final protection scheme must be designed according to generator ratings, grounding arrangement, transformer connection, neutral arrangement, plant operating philosophy and applicable protection standards.
3. REG650 Generator Protection System Architecture
A typical generator protection system includes the following equipment:
- Synchronous generator
- Generator circuit breaker
- Generator current transformers
- Generator voltage transformers
- Neutral grounding equipment
- Generator step-up transformer
- Field excitation system
- Prime mover and turbine control system
- REG650 protection IED
- Backup protection IEDs
- Station control and monitoring system
The REG650 receives analogue measurement signals from CTs and VTs and binary signals from the generator and associated equipment.
The relay processes these inputs using its configured protection functions and generates trip, alarm and control signals.
3.1 Typical CT Connections
Current transformers are used to measure generator phase currents and provide inputs for protection functions such as:
- Generator differential protection
- Overcurrent protection
- Negative-sequence protection
- Reverse-power protection
- Stator earth-fault protection, where applicable
- Breaker failure protection
For generator differential protection, CTs are installed at the generator terminal and neutral ends of the protected zone.
Correct CT ratio, polarity and phase identification are essential.
3.2 Voltage Transformer Connections
Voltage transformers provide voltage signals for functions such as:
- Generator differential or voltage-dependent applications, where applicable
- Loss-of-excitation protection
- Overvoltage protection
- Undervoltage protection
- Overexcitation protection
- Underfrequency and overfrequency protection
- Synchronism-related supervision
- Voltage-restrained overcurrent protection
The VT connection must be selected according to the generator voltage system and protection design.
3.3 Generator Neutral Grounding
Generator neutral grounding arrangements have a significant influence on stator earth-fault protection.
Common arrangements include:
- Resistance grounding
- Distribution transformer grounding
- Grounding through a grounding transformer
- Other engineered neutral grounding arrangements
The grounding method determines the available earth-fault current and influences the selection and sensitivity of the earth-fault protection scheme.
4. Main Protection Functions of REG650
The exact functions available depend on the product version, selected application configuration, hardware and ordering code.
The following sections explain important generator protection functions associated with REG650.
5. Generator Differential Protection – GENPDIF
Generator differential protection is one of the most important functions in a generator protection system.
It detects internal faults within the protected generator stator winding zone by comparing currents entering and leaving the protected zone.
The operating principle is based on Kirchhoff’s current law.
Under normal operating conditions, the currents entering and leaving the protected zone should be approximately equal, after considering CT ratios and polarity.
For an internal fault, the differential current increases.
A simplified differential-current expression is:
[
I_{\mathrm{diff}}=|I_1-I_2|
]
where:
- (I_1) is the current measured at one boundary of the protected zone.
- (I_2) is the corresponding current at the other boundary, referred to the same polarity convention.
In practical differential protection, the relay uses stabilisation or restraint characteristics to maintain security during external faults and CT saturation.
5.1 Operating Principle
The generator differential protection scheme typically uses:
- Generator terminal CTs
- Generator neutral-end CTs
- Differential current calculation
- Restraint or stabilisation characteristics
- Differential operating characteristic
- Trip logic
During normal load conditions, the differential current should remain close to zero.
During an external fault, the currents should remain balanced when the CTs operate correctly.
During an internal fault, the differential current increases and the protection operates when its configured criteria are satisfied.
5.2 Generator Differential Protection Applications
Typical internal faults detected by differential protection include:
- Phase-to-phase faults
- Three-phase faults
- Phase-to-earth faults within the protected zone, depending on the grounding arrangement and fault-current level
The differential protection zone is defined by the physical CT locations.
5.3 Engineering Considerations
During commissioning, verify:
- CT ratios
- CT polarity
- Phase identification
- Differential zone boundaries
- CT secondary wiring
- Current measurement scaling
- Differential pickup
- Restraint characteristic
- Trip output logic
A secondary injection test should verify the differential protection response under balanced and unbalanced current conditions.
Important: Not every REG650 configuration includes generator differential protection. Some configurations provide generator differential protection, while others may be ordered with transformer differential protection. Confirm the actual ordered configuration before preparing the protection settings.
6. Stator Earth-Fault Protection
Stator earth faults are among the most important generator protection concerns.
An earth fault can occur because of:
- Insulation deterioration
- Moisture contamination
- Thermal ageing
- Mechanical damage
- Winding vibration
- Electrical stress
- Contamination inside the generator
The protection scheme must detect earth faults while avoiding unnecessary operation during normal generator conditions.
REG650 supports earth-fault protection arrangements according to the selected configuration and generator grounding system.
6.1 Neutral Overvoltage Protection
Residual overvoltage protection can be used to detect stator earth faults.
The function commonly identified as ROV2PTOV measures residual voltage, often derived from the open-delta VT connection or another suitable measurement arrangement.
For a healthy balanced three-phase system:
[
U_a+U_b+U_c \approx 0
]
An earth fault causes an imbalance and produces residual voltage.
The protection detects this voltage and operates according to the configured pickup and time delay.
6.2 Third-Harmonic-Based Stator Earth-Fault Protection
The function STEFPHIZ is associated with third-harmonic-based stator earth-fault protection.
The principle uses third-harmonic voltage distribution between the generator neutral and terminal sides.
The third-harmonic voltage distribution changes when an earth fault occurs at different locations along the stator winding.
This method can help extend stator earth-fault coverage towards the generator neutral point.
The actual coverage depends on the generator’s third-harmonic characteristics, operating conditions, measurement arrangement and protection settings.
6.3 100% Stator Earth-Fault Protection
A complete stator earth-fault protection scheme may combine:
- Fundamental-frequency neutral overvoltage protection
- Third-harmonic-based protection
- Additional suitable earth-fault protection methods
The aim is to detect faults across the stator winding, including areas close to the neutral point that may not produce sufficient fundamental-frequency residual voltage.
The function availability and required hardware must be checked against the relevant REG650 product guide.
7. Rotor Earth-Fault Protection
The rotor field winding is normally insulated from earth.
An initial earth fault may not immediately produce a large fault current, but a second earth fault at another location can create a dangerous short-circuit path through part of the rotor winding.
Possible consequences include:
- Rotor heating
- Magnetic field distortion
- Mechanical vibration
- Rotor damage
- Generator instability
REG650 configurations can support rotor ground protection using the RXTTE4 injection unit.
This arrangement is different from conventional stator earth-fault protection because it monitors the insulation condition of the rotor field circuit.
During engineering, the protection arrangement must be coordinated with the excitation system and the selected rotor-ground monitoring equipment.
8. Loss-of-Excitation Protection
Loss of excitation is a serious abnormal condition in a synchronous generator.
It can occur because of:
- Excitation-system failure
- Field circuit interruption
- Excitation breaker tripping
- AVR malfunction
- Loss of field supply
- Incorrect excitation control operation
When a synchronous generator loses excitation, it may continue operating while absorbing reactive power from the connected network.
This can lead to:
- Increased stator current
- Rotor heating
- Reduced stability margin
- Voltage instability
- Pole slipping
- Disturbances in the connected power system
Loss-of-excitation protection typically uses impedance-based characteristics measured at the generator terminals.
The protection identifies operating conditions associated with loss of field and initiates the required trip or alarm action.
Setting considerations include:
- Generator capability curve
- Generator impedance
- Excitation-system characteristics
- System impedance
- Operating power factor
- Time delays
- Coordination with other protection functions
The actual function block and characteristic must be confirmed from the applicable REG650 product version and application manual.
9. Overexcitation Protection – OEXPVPH
Overexcitation occurs when the magnetic flux in the generator or connected transformer exceeds its permissible design limit.
The flux level is approximately proportional to the voltage-to-frequency ratio:
[
\text{Flux}\propto\frac{V}{f}
]
Therefore, excessive voltage or reduced frequency can produce an overexcitation condition.
Possible causes include:
- Generator operation at excessive voltage
- Low-frequency operation
- AVR malfunction
- Incorrect voltage regulation
- Incorrect generator operating conditions
Overexcitation can cause:
- Core saturation
- Excessive magnetising current
- Localised heating
- Insulation deterioration
- Transformer and generator damage
The OEXPVPH function provides overexcitation protection based on the configured voltage-to-frequency relationship and operating characteristic.
Settings must be coordinated with the generator and transformer manufacturer’s permissible V/Hz limits.
10. Negative-Sequence Overcurrent Protection – NS2PTOC
Unbalanced loading produces negative-sequence current in a synchronous generator.
Negative-sequence current creates a magnetic field rotating in the opposite direction to the rotor.
This induces double-frequency currents in the rotor body and associated conductive components, causing additional heating.
Typical causes include:
- Unbalanced system faults
- Unequal phase loading
- Open conductor conditions
- Unbalanced switching operations
- Incorrect phase connections
The NS2PTOC function provides negative-sequence time overcurrent protection.
Generator manufacturers normally specify permissible negative-sequence current limits, often expressed through an (I_2^2t) withstand characteristic.
The protection settings must be coordinated with the generator manufacturer’s thermal capability.
11. Voltage-Restrained Overcurrent Protection – VR2PVOC
Voltage-restrained overcurrent protection is useful as backup protection for generator faults.
During a nearby system fault, generator terminal voltage may decrease while fault current increases.
A conventional overcurrent element may not always provide sufficient sensitivity under all generator operating conditions.
Voltage-restrained overcurrent protection uses voltage information to modify the overcurrent operating characteristic.
The VR2PVOC function can provide backup protection for generator and associated system faults.
Important setting considerations include:
- Generator rated current
- Minimum operating voltage
- Pickup current
- Time characteristic
- Coordination with external protection
- Generator fault-current decrement
12. Directional and Non-Directional Overcurrent Protection
REG650 supports several current protection functions depending on the configuration.
Important function blocks include:
- OC4PTOC – Four-step phase overcurrent protection
- EF4PTOC – Four-step residual overcurrent protection
- SDEPSDE – Sensitive directional residual overcurrent and power protection
These functions can provide backup protection and detect abnormal current conditions.
12.1 Phase Overcurrent Protection
OC4PTOC provides multiple stages of phase overcurrent protection.
It can be used as:
- Generator backup protection
- Transformer backup protection
- Busbar backup protection
- External network fault backup protection
12.2 Residual Overcurrent Protection
EF4PTOC provides residual overcurrent protection.
It can be used for earth-fault detection, with directional supervision where required by the grounding arrangement.
12.3 Sensitive Directional Residual Overcurrent Protection
SDEPSDE provides sensitive directional residual current and power protection.
It is particularly relevant where low earth-fault current levels require sensitive detection.
The correct application depends on the neutral grounding arrangement and the available voltage and current polarising quantities.
13. Reverse Power Protection – GUPPDUP
Reverse power protection detects situations where the generator begins absorbing active power from the electrical network.
This can happen when the prime mover loses its mechanical input while the generator remains connected to the grid.
For example, if a steam turbine loses steam supply, the generator may begin operating as a motor.
Possible consequences include:
- Turbine mechanical stress
- Heating
- Damage to prime mover components
- Unwanted motoring operation
The GUPPDUP function provides directional underpower protection and can be applied in generator reverse-power schemes.
The settings must consider:
- Generator rated power
- Normal auxiliary power consumption
- Minimum stable operating power
- Prime mover characteristics
- Turbine or engine manufacturer’s requirements
- Operating delays
A suitable time delay is important to avoid unnecessary operation during normal transient conditions.
14. Overpower Protection – GOPPDOP
The GOPPDOP function provides directional overpower protection.
It can be used to detect excessive active power conditions in the configured direction.
Possible applications include:
- Generator overload supervision
- Power-flow supervision
- Operating-limit monitoring
- Supplementary protection
The function should be coordinated with the generator capability limits and plant operating philosophy.
15. Accidental Energisation Protection – AEGGAPC
Accidental energisation occurs when a generator is energised unexpectedly while it is stopped or not operating at the expected speed and voltage conditions.
Possible causes include:
- Generator circuit-breaker closing during maintenance
- Incorrect switching operation
- Control circuit malfunction
- Unintended breaker operation
- Incorrect synchronising logic
Accidental energisation can produce high currents and serious mechanical and electrical stresses.
The AEGGAPC function provides protection against accidental energisation of a synchronous generator.
The protection scheme should be coordinated with:
- Generator breaker status
- Generator voltage
- Current measurement
- Speed or operating-state information, where applicable
- Closing logic
- Generator isolation arrangements
16. Overvoltage and Undervoltage Protection
Generator voltage must remain within permissible operating limits.
REG650 can provide voltage protection using functions such as:
- OV2PTOV – Two-step overvoltage protection
- UV2PTUV – Two-step undervoltage protection
- ROV2PTOV – Residual overvoltage protection
16.1 Overvoltage Protection
Overvoltage can occur because of:
- AVR malfunction
- Sudden load rejection
- Incorrect excitation control
- Switching operations
- Network disturbances
Excessive voltage can damage generator insulation and connected equipment.
16.2 Undervoltage Protection
Undervoltage can occur because of:
- Generator overload
- Excitation problems
- Network faults
- Voltage-control malfunction
- System instability
The function can be used for alarm or trip applications according to the protection design.
17. Frequency Protection
Generator frequency protection is important because the generator’s mechanical speed and electrical frequency are directly related.
REG650 can support:
- SAPTUF – Underfrequency protection
- SAPTOF – Overfrequency protection
- SAPFRC – Rate-of-change-of-frequency protection
17.1 Underfrequency Protection
Underfrequency can occur when the connected system experiences a generation-load imbalance.
Possible causes include:
- Loss of generation
- Sudden increase in load
- Islanding
- Network separation
Underfrequency protection can be used for generator protection, load-shedding coordination or system separation schemes, depending on the application.
17.2 Overfrequency Protection
Overfrequency can occur when generation exceeds the connected load or following a sudden load rejection.
The protection monitors frequency and operates according to configured thresholds and delays.
17.3 Rate-of-Change-of-Frequency Protection
Rate-of-change-of-frequency protection detects rapid frequency variations.
It can support applications requiring early detection of major generation-load imbalances or islanding conditions.
18. Thermal Overload Protection – TRPTTR
Generator stator windings and associated equipment have thermal operating limits.
Excessive current can cause overheating and insulation deterioration.
TRPTTR provides thermal overload protection using a thermal model with two time constants.
The thermal model estimates the thermal state based on measured current and configured parameters.
The protection can generate alarms or trip commands when the calculated thermal condition exceeds the configured limits.
Setting considerations include:
- Rated current
- Thermal time constants
- Permissible overload
- Cooling characteristics
- Generator manufacturer’s thermal data
19. Breaker Failure Protection – CCRBRF
Circuit-breaker failure protection is important in generator protection schemes.
When a generator protection function issues a trip command, the generator circuit breaker should interrupt the fault current.
If the breaker fails to open, the fault may remain connected to the generator or network.
The CCRBRF function supervises the breaker response after a trip command.
Typical inputs include:
- Breaker trip initiation
- Current measurement
- Breaker auxiliary contacts
- Timer and reset logic
If the breaker fails to interrupt the current within the configured time, breaker failure protection can initiate backup tripping.
The backup trip arrangement must be designed according to the substation and generator protection architecture.
20. Pole Discordance Protection – CCRPLD
Pole discordance occurs when the three poles of a circuit breaker do not operate consistently.
For example, one pole may remain closed while the other two poles open.
This can create an unbalanced operating condition and abnormal negative-sequence quantities.
CCRPLD provides pole discordance protection and can be used to detect inconsistent breaker pole conditions.
21. Generator Step-Up Transformer Protection
REG650 configurations can support generator and transformer protection applications.
Depending on the ordered variant, transformer differential protection may be included instead of generator differential protection.
The transformer protection arrangement may include:
- Transformer differential protection
- Restricted earth-fault protection, where configured
- Overcurrent backup protection
- Overexcitation protection
- Transformer thermal protection
For a generator-transformer unit, engineers must clearly define the protection zones and coordinate the generator and transformer protection systems.
The transformer differential function must account for:
- Transformer vector group
- CT ratios
- Phase compensation
- Tap-changer range
- Magnetising inrush
- Overexcitation
- CT saturation
Do not assume that every REG650 includes both generator differential and transformer differential protection. Check the exact order code and product guide.
22. REG650 Application Configurations
REG650 is supplied in predefined and customised configurations.
The available configurations depend on product version and ordering options.
The product guide identifies configurations that can include:
- Generator differential protection
- Generator and transformer protection arrangements
- Backup protection functions
- Monitoring and control functions
- Communication interfaces
For example, product documentation for certain REG650 versions identifies generator differential and generator-plus-transformer differential variants.
Before selecting a relay, engineers should check:
- Generator rated voltage and current
- Generator MVA rating
- Generator neutral grounding method
- CT and VT requirements
- Required differential protection zones
- Stator earth-fault protection requirements
- Rotor earth-fault protection requirements
- Binary input/output requirements
- Communication protocols
- Hardware and ordering code
23. Hardware Architecture
REG650 uses the common hardware platform of the Relion 650 series.
Depending on the selected configuration, hardware modules may include:
- Power supply module
- Main processing module
- Transformer input module
- Analogue input module
- Binary input/output modules
- Communication module
- Ethernet interface
- Local human-machine interface
23.1 Current and Voltage Inputs
Current and voltage measurement modules receive the analogue signals from external CTs and VTs.
The selected module must match the project requirements and measurement circuit design.
23.2 Binary Inputs
Binary inputs receive external status and control signals.
Examples include:
- Generator circuit-breaker status
- Field breaker status
- Turbine trip
- Emergency shutdown
- Protection blocking
- External interlocking
- Alarm contacts
23.3 Binary Outputs
Binary outputs can be assigned to:
- Generator trip
- Field breaker trip
- Alarm
- Breaker failure initiation
- External protection signalling
- Control system indications
The final output allocation must follow the approved trip matrix.
24. PCM600 Engineering and Configuration
ABB PCM600 is the main engineering platform for REG650.
It provides tools for:
- IED configuration
- Application logic engineering
- Parameter setting
- Signal mapping
- Communication configuration
- IEC 61850 engineering
- Monitoring and maintenance
24.1 Creating a PCM600 Project
A typical engineering workflow is:
- Start PCM600.
- Create a new project.
- Add the REG650 IED.
- Select the correct product version.
- Select the appropriate hardware configuration.
- Import or create the application configuration.
- Configure protection functions.
- Configure signal connections.
- Configure communication.
- Validate the project before writing it to the IED.
The PCM600 connectivity package must support the installed REG650 product version.
24.2 Application Configuration Tool
The Application Configuration Tool (ACT) is used to configure the internal application logic.
Typical tasks include:
- Connecting CT and VT measurement signals
- Connecting protection function inputs
- Configuring trip logic
- Assigning blocking signals
- Connecting alarms
- Mapping internal signals to outputs
24.3 Parameter Setting
Protection settings must be calculated from the generator data and approved protection coordination study.
Important parameters include:
- CT ratios
- VT ratios
- Generator rated current
- Generator rated voltage
- Generator rated power
- Differential protection settings
- Overcurrent pickup values
- Negative-sequence limits
- Voltage protection thresholds
- Frequency thresholds
- Time delays
- Trip logic
24.4 Signal Matrix Tool
Signal Matrix Tool (SMT) is used to map internal IED signals to physical binary inputs and outputs and other relevant destinations.
Correct mapping is essential for reliable operation.
24.5 IEC 61850 Engineering
PCM600 supports IEC 61850 engineering for the REG650.
Typical engineering tasks include:
- Logical device configuration
- Logical node configuration
- Dataset creation
- Report control block configuration
- GOOSE communication
- Signal mapping
- SCL file management
The engineering must be coordinated with the station-level system and other protection IEDs.
25. IEC 61850 Communication
REG650 can communicate with substation automation systems using IEC 61850.
25.1 MMS Communication
Manufacturing Message Specification (MMS) is used for client-server communication between the IED and station-level systems.
It supports:
- Measurement monitoring
- Status reporting
- Alarm reporting
- Event reporting
- Control and supervision
25.2 GOOSE Communication
GOOSE messaging provides fast peer-to-peer communication between IEDs.
Typical applications include:
- Generator breaker status exchange
- Interlocking
- External blocking
- Protection signalling
- Breaker failure signalling
- Trip-related logic
25.3 SCL Engineering
Substation Configuration Language files are used to describe and exchange IEC 61850 system configurations.
Depending on the engineering workflow, relevant SCL files include:
- ICD
- IID
- CID
- SCD
The final configuration must be consistent between the IED and the station-level engineering system.
26. Commissioning and Testing of REG650
Commissioning is an essential stage in ensuring that REG650 operates correctly and reliably.
A comprehensive test plan should include hardware inspection, measurement verification, protection testing, logic testing and communication testing.
26.1 Visual Inspection
Check:
- Correct IED model
- Correct product version
- Hardware module arrangement
- Auxiliary supply
- CT wiring
- VT wiring
- Binary input wiring
- Binary output wiring
- Communication connections
- Earthing and panel installation
26.2 CT Circuit Testing
Verify:
- CT ratio
- CT polarity
- Phase identification
- Secondary wiring
- Star-point arrangement
- CT earthing
- Differential protection zone connections
Incorrect CT polarity can cause unwanted differential protection operation.
26.3 VT Circuit Testing
Verify:
- VT ratio
- Phase sequence
- Phase identification
- Secondary fuse and MCB arrangements
- Residual voltage connections
- Voltage measurement scaling
26.4 Differential Protection Testing
For generator differential protection, use a suitable relay test set to verify:
- Differential pickup
- Restraint characteristic
- Operating characteristic
- Stability during external fault simulation
- Operation during internal fault simulation
- Phase identification
- Trip output
The testing procedure must reflect the actual CT connection and differential protection configuration.
26.5 Overcurrent Protection Testing
Test each enabled overcurrent stage.
Verify:
- Pickup current
- Drop-off behaviour
- Operating time
- Time characteristic
- Directional supervision, if applicable
- Blocking signals
- Trip output
26.6 Negative-Sequence Protection Testing
Inject unbalanced three-phase current signals and verify the negative-sequence calculation.
Check the pickup threshold, operating characteristic and configured time delay.
26.7 Voltage and Frequency Protection Testing
Test the enabled voltage and frequency functions.
Verify:
- Undervoltage pickup
- Overvoltage pickup
- Underfrequency threshold
- Overfrequency threshold
- Rate-of-change-of-frequency response
- Operating time
- Reset behaviour
26.8 Reverse-Power Protection Testing
Inject suitable voltage and current signals to simulate active power in the reverse direction.
Verify the directional power calculation, pickup threshold, operating delay and trip output.
26.9 Binary Input and Output Testing
Check all assigned binary inputs and outputs.
Examples include:
- Generator breaker open
- Generator breaker closed
- Field breaker status
- Turbine trip
- External trip
- Generator protection trip
- Alarm outputs
26.10 IEC 61850 Testing
Verify:
- MMS communication
- Report control blocks
- GOOSE publishing
- GOOSE subscriptions
- Signal mapping
- Communication supervision
- SCL consistency
26.11 Disturbance Recorder Testing
Verify that the disturbance recorder captures the configured analogue and binary signals when the selected trigger conditions occur.
Retrieve the disturbance records and check timestamps, channels and recorded waveforms.
27. Common REG650 Problems and Troubleshooting
Problem 1: Generator Differential Protection Trips During Normal Operation
Possible causes:
- Incorrect CT polarity
- Incorrect CT ratio
- Phase mismatch
- Incorrect differential zone wiring
- CT secondary circuit problems
- Incorrect parameter settings
Recommended checks:
- Verify CT polarity at both ends.
- Check CT ratio settings.
- Compare phase currents.
- Verify the differential zone boundaries.
- Review disturbance records.
- Confirm the application configuration.
Problem 2: Earth-Fault Protection Does Not Operate
Possible causes:
- Incorrect neutral VT connection
- Incorrect residual voltage measurement
- Incorrect grounding arrangement settings
- Incorrect pickup threshold
- Incorrect function configuration
- Missing measurement signal
Check the neutral grounding design and verify the actual residual voltage input.
Problem 3: Reverse-Power Protection Operates Incorrectly
Possible causes:
- Incorrect CT polarity
- Incorrect VT phase assignment
- Incorrect power direction setting
- Incorrect active-power threshold
- Incorrect time delay
Verify the power measurement and directional reference before changing protection settings.
Problem 4: Negative-Sequence Protection Operates During Normal Operation
Possible causes:
- Unbalanced CT secondary circuits
- Incorrect CT polarity
- Actual phase-current imbalance
- Incorrect pickup setting
- Generator operating conditions outside the expected range
Review the three-phase current measurements and negative-sequence value.
Problem 5: IEC 61850 Communication Failure
Possible causes:
- Incorrect IP address
- Incorrect network configuration
- Incorrect SCL file
- Dataset mismatch
- GOOSE configuration problem
- Network switch configuration issue
Check the IED communication settings, SCL engineering and network connectivity.
Problem 6: PCM600 Cannot Connect to REG650
Possible causes:
- Incorrect IP settings
- PC and IED on different subnets
- Incorrect connectivity package
- Incorrect technical key
- Communication cable or switch problem
- Access control restrictions
Verify the network connection and confirm that the PCM600 project corresponds to the actual IED.
28. REG650 Compared with REG670
REG650 and REG670 are both generator protection IEDs in the Relion family, but they belong to different product series and address different application requirements.
| Feature | REG650 | REG670 |
|---|---|---|
| Product family | Relion 650 | Relion 670 |
| Main application | Generator protection | Generator protection |
| Typical application scope | Small and medium-sized generators | Broad generator protection applications, including more demanding transmission-level schemes |
| Engineering | PCM600 | PCM600 |
| IEC 61850 | Supported | Supported |
| Differential protection | Configuration-dependent | Configuration-dependent |
| Backup protection | Available functions depend on configuration | Broad protection and control options |
| Application philosophy | Predefined and configurable solutions | Flexible protection and control platform |
The selection should be based on generator size, protection philosophy, required functions, redundancy, hardware and project specifications rather than product-series number alone.
29. Frequently Asked Questions
What is ABB REG650?
ABB REG650 is a generator protection and control IED from the Relion 650 series. It is designed to protect and monitor synchronous generators and associated equipment.
What generators can REG650 protect?
It can be applied to generators in hydro, pumped-storage, gas, diesel, steam, combined-cycle, cogeneration and renewable power plants, subject to the application and configuration.
Does REG650 support generator differential protection?
Yes, certain REG650 configurations support generator differential protection. The available differential protection arrangement depends on the ordered variant.
Does REG650 support transformer differential protection?
Certain configurations support transformer differential protection. Check the product guide and ordering code because generator differential and transformer differential options may be mutually exclusive in specified configurations.
Does REG650 provide 100% stator earth-fault protection?
The relay supports third-harmonic-based stator earth-fault protection in applicable configurations. Complete stator winding coverage depends on the protection arrangement, generator characteristics and engineering settings.
Does REG650 support rotor earth-fault protection?
Applicable configurations support rotor ground protection using the RXTTE4 injection unit.
Which software is used to configure REG650?
ABB PCM600 is used for engineering, application configuration, parameter setting and communication configuration.
Does REG650 support IEC 61850?
Yes. REG650 supports IEC 61850 integration for substation automation applications, including MMS and GOOSE functionality where configured.
Can REG650 protect the generator step-up transformer?
Certain configurations provide transformer protection functions. The exact protection scheme must be confirmed from the product guide and selected ordering code.
What is the difference between REG650 and REG670?
Both are generator protection IEDs, but they belong to different Relion product series and have different application configurations and engineering options. Selection should be based on the project requirements and supported functions.
30. Conclusion
The ABB REG650 is a flexible generator protection and control IED designed for small and medium-sized generation applications.
Its protection functions can cover important generator fault conditions, including stator faults, earth faults, negative-sequence currents, loss of excitation, reverse power, overexcitation, abnormal voltage and frequency conditions.
The combination of predefined application configurations, PCM600 engineering and IEC 61850 communication makes REG650 suitable for integration into modern generator protection and substation automation systems.
For protection engineers, commissioning specialists and power plant maintenance teams, practical knowledge of REG650 requires an understanding of generator protection philosophy, CT and VT circuits, differential protection, stator earth-fault protection, rotor grounding, protection coordination and relay testing.
Technical note: This article describes the REG650 platform and representative functions. The actual function inventory depends on product version, application configuration, hardware and ordering code. Always consult the applicable REG650 Product Guide, Application Manual, Technical Manual and Commissioning Manual before engineering or commissioning an IED.

