ABB REL650 Line Distance Protection Relay – Complete Technical Guide

Table Of Contents
  1. 1. Introduction to ABB REL650
  2. 2. Main Applications of REL650
  3. 3. REL650 Product Configurations
  4. 4. Distance Protection Operating Principle
  5. 5. Distance Protection Zones in REL650
  6. 6. Quadrilateral and Mho Distance Characteristics
  7. 7. Main Distance Protection Function – ZMFPDIS
  8. 8. Earth-Fault Distance Protection
  9. 9. Phase Selection and Single-Phase Tripping
  10. 10. Load Encroachment Protection
  11. 11. Adaptive Reach Compensation
  12. 12. Power Swing Detection and Blocking
  13. 13. Automatic Switch-Onto-Fault Protection
  14. 14. Backup Overcurrent Protection
  15. 15. Additional Protection and Supervision Functions
  16. 16. Circuit-Breaker Failure Protection
  17. 17. Auto-Reclosing and Synchronism Check
  18. 18. CT and VT Requirements
  19. 19. Line Impedance Calculations and Settings
  20. 20. PCM600 Engineering and Configuration
  21. 21. IEC 61850 Communication in REL650
  22. 22. Testing and Commissioning of REL650
  23. 23. Common REL650 Problems and Troubleshooting
  24. 24. REL650 vs REL670 – Main Differences
  25. 25. Frequently Asked Questions About ABB REL650
  26. 26. Conclusion
  27. Related Articles

ABB REL650 Line Distance Protection Relay – Complete Technical Guide

1. Introduction to ABB REL650

The ABB REL650 is a numerical line distance protection relay from the ABB Relion 650 series. It is designed for the protection, control and monitoring of overhead transmission lines and cables in solidly earthed or impedance-earthed power systems.

The REL650 is particularly suitable for sub-transmission applications where reliable distance protection, backup protection, automatic reclosing and circuit-breaker control are required.

The relay combines distance protection with several additional functions, including:

  • Phase and earth-fault distance protection
  • Quadrilateral and mho impedance characteristics
  • Power swing detection and logic
  • Out-of-step protection
  • Load encroachment protection
  • Adaptive reach compensation
  • Phase and residual overcurrent protection
  • Circuit-breaker failure protection
  • Auto-reclosing and synchronism check
  • IEC 61850 communication
  • Disturbance recording and event monitoring

REL650 is supplied in preconfigured application packages. The available hardware, protection functions and application logic depend on the selected configuration and product version.

2. Main Applications of REL650

2.1 Overhead transmission line protection

REL650 is designed to protect overhead lines in transmission and sub-transmission networks.

Distance protection measures the voltage and current at the relay location and calculates the apparent impedance between the relay and the fault.

Because line impedance is approximately proportional to line length, the relay can estimate whether a fault is within its configured protection zones.

2.2 Cable protection

The REL650 can also be applied to suitable cable protection applications.

Cable impedance characteristics, charging current, grounding arrangements and network configuration must be considered when selecting and setting the protection functions.

2.3 Heavily loaded transmission lines

The REL650 product documentation describes applications involving heavily loaded lines. Load encroachment and adaptive reach compensation features help address specific distance protection challenges.

The protection engineer must nevertheless verify the maximum expected loading and ensure that the selected settings provide adequate security and sensitivity.

2.4 Multi-terminal line applications

Multi-terminal lines introduce additional challenges for distance protection because current contributions can come from more than two locations.

Remote infeed, fault resistance and changing network configurations can affect the apparent impedance measured at a line terminal.

The complete application must be studied to determine suitable zone reaches, operating times and any communication-assisted protection requirements.

3. REL650 Product Configurations

ABB provides preconfigured REL650 application packages to simplify engineering and commissioning.

The REL650 Version 2.2 Product Guide describes configurations including:

ConfigurationGeneral application
REL650 A11Single circuit-breaker application with single-phase tripping
REL650 A12Single circuit-breaker application with three-phase tripping for high-ohmic and resonance-earthed systems

The configurations include predefined analog and control circuits. The engineer can adapt the application to the actual substation design.

When selecting a relay, verify:

  • Required CT and VT inputs
  • Single-phase or three-phase tripping philosophy
  • Network grounding arrangement
  • Circuit-breaker arrangement
  • Binary input and output requirements
  • Communication interfaces
  • Required protection functions
  • Product version and ordering information

The configuration names and available functions should always be checked against the exact ABB ordering documentation.

4. Distance Protection Operating Principle

Distance protection is based on the apparent impedance measured at the relay location.

The basic relationship is:

Z = V / I

Where:

  • Z is the apparent impedance
  • V is the measured voltage
  • I is the measured current

During a fault, the measured voltage and current change. The relay calculates the apparent impedance and compares it with its configured impedance characteristics.

For a uniform transmission line, impedance is approximately proportional to line length.

For example, if the total line impedance is 10 ohms, a fault at approximately half the line length may produce a measured impedance close to 5 ohms under simplified conditions.

Actual measurements are affected by fault resistance, source impedance, remote infeed, mutual coupling, CT and VT errors, and other power-system conditions.

5. Distance Protection Zones in REL650

The REL650 Version 2.2 product documentation describes a full-scheme distance protection function with six zones. These zones have independent measuring and setting ranges.

This provides flexibility for different line configurations and protection coordination requirements.

5.1 Zone 1

Zone 1 is normally configured to cover approximately 80–90% of the protected line.

It is generally set for instantaneous operation, without an intentional time delay.

The reach is normally set below the complete line impedance to reduce the risk of overreaching beyond the remote busbar.

5.2 Zone 2

Zone 2 provides additional coverage beyond the end of the protected line.

It is usually time-delayed to coordinate with the remote-end protection and adjacent network protection.

5.3 Zone 3

Zone 3 can provide remote backup protection for faults beyond the remote busbar.

Its reach and operating time must be coordinated with the protection of adjacent lines and other network equipment.

5.4 Additional distance zones

The remaining distance zones can be assigned according to the protection philosophy.

Depending on the application, they may be used for:

  • Extended backup protection
  • Reverse-looking protection
  • Teleprotection schemes
  • Protection coordination
  • Special network configurations

The direction, reach and time delay of every zone should be established through a protection study.

6. Quadrilateral and Mho Distance Characteristics

The REL650 distance protection function supports quadrilateral and mho characteristics.

6.1 Quadrilateral characteristic

The quadrilateral characteristic provides separate resistive and reactive reach settings.

This is useful for applications where fault resistance is significant.

The characteristic allows the engineer to define the resistive and reactive boundaries independently, helping improve coverage of resistive faults.

Important considerations include:

  • Resistive reach for phase faults
  • Resistive reach for earth faults
  • Reactive reach
  • Forward and reverse direction
  • Load encroachment
  • Fault resistance
  • Maximum load conditions

6.2 Mho characteristic

The mho characteristic is widely used in transmission line distance protection.

It has an inherently directional characteristic and can be suitable for applications involving long lines and changing system conditions.

The engineer must verify the configured reach, characteristic angle and operating direction.

6.3 Selecting the correct characteristic

The selection between quadrilateral and mho characteristics depends on:

  • Line length and impedance angle
  • Expected fault resistance
  • Maximum loading
  • System stability conditions
  • Network topology
  • Protection coordination requirements

The selected characteristic should be tested over its complete operating boundary.

7. Main Distance Protection Function – ZMFPDIS

One of the main protection functions in REL650 is:

ZMFPDIS – Distance Protection, Quadrilateral and Mho Characteristic

This function provides the main impedance-based protection capability.

The function evaluates the apparent impedance for phase and earth faults and determines whether the measured impedance falls within the configured protection zones.

Important engineering parameters include:

  • Zone reach
  • Resistive reach
  • Reactive reach
  • Zone direction
  • Zone operating time
  • Earth-fault compensation
  • Load encroachment
  • Phase selection and trip logic

The function’s detailed setting parameters and available options depend on the installed product version.

8. Earth-Fault Distance Protection

Earth faults are common in overhead transmission networks.

For correct earth-fault distance measurement, the relay must compensate for the zero-sequence impedance of the line.

A commonly used representation of the zero-sequence compensation factor is:

K0 = (Z0 − Z1) / (3 × Z1)

Where:

  • Z0 is the zero-sequence line impedance
  • Z1 is the positive-sequence line impedance

The relay uses phase and residual quantities to calculate the apparent impedance for phase-to-earth faults.

Important considerations include:

  • Positive-sequence impedance
  • Zero-sequence impedance
  • Earth-return compensation
  • CT polarity
  • Residual current measurement
  • Line grounding arrangement
  • Parallel-line mutual coupling

Incorrect zero-sequence compensation can cause distance protection to overreach or underreach during earth faults.

The compensation convention and setting format must be checked against the REL650 application manual.

9. Phase Selection and Single-Phase Tripping

Correct phase selection is important for transmission line protection, especially when single-phase auto-reclosing is used.

The relay must identify the faulted phase or phases.

Typical fault types include:

  • Phase A to earth
  • Phase B to earth
  • Phase C to earth
  • Phase-to-phase faults
  • Two-phase-to-earth faults
  • Three-phase faults

The REL650 application configuration determines the available tripping philosophy.

In a single-phase tripping application, the relay can trip the affected pole for a suitable single-phase-to-earth fault, while keeping the healthy phases in service when the protection scheme permits.

For three-phase tripping applications, the trip logic operates all three circuit-breaker poles.

The engineer must coordinate phase selection, trip outputs, circuit-breaker pole supervision and auto-reclosing logic.

10. Load Encroachment Protection

During heavy loading conditions, the apparent impedance seen by a distance relay can approach or enter the distance protection characteristic.

If the protection is not correctly engineered, this can result in unwanted operation during normal or emergency loading.

Load encroachment logic helps distinguish load conditions from fault conditions.

When configuring this feature, consider:

  • Maximum continuous loading
  • Emergency loading
  • Power factor
  • Minimum operating voltage
  • Line thermal limits
  • System operating scenarios
  • Distance zone characteristics

Load encroachment settings should be coordinated with the distance protection zones to maintain both security and fault sensitivity.

11. Adaptive Reach Compensation

The REL650 product documentation identifies adaptive reach compensation as one of its distance protection capabilities.

This feature is intended to address reach-related challenges under changing application conditions.

The actual use and configuration depend on the selected application and product version.

Protection engineers should study the relevant ABB technical documentation before enabling or modifying this function.

12. Power Swing Detection and Blocking

Power swings can occur after major disturbances such as:

  • Loss of a transmission line
  • Generator tripping
  • Major short circuits
  • Sudden changes in generation or load
  • System separation

During a power swing, the apparent impedance can move through the distance protection characteristic even though no short circuit exists.

This can cause unwanted distance relay operation if the protection is not properly supervised.

The REL650 documentation includes the following power swing-related functions:

FunctionDescription
ZMRPSBPower swing detection
PSLPSCHPower swing logic
OOSPPAMOut-of-step protection

Power swing detection identifies impedance movement associated with a power swing.

Power swing logic can provide blocking or other configured supervision of distance protection.

Out-of-step protection addresses system conditions where the power system loses synchronism, according to the configured application.

Stable and unstable power swings must be treated differently. The protection philosophy should be coordinated with the system stability study.

13. Automatic Switch-Onto-Fault Protection

The REL650 product documentation includes:

ZCVPSOF – Automatic Switch Onto Fault Logic

This function is intended for situations where a line or circuit is energized onto an existing fault.

A fault may exist on a line that has been isolated and is subsequently energized by a circuit-breaker closing operation.

The protection must respond rapidly because the normal distance protection scheme may not operate in the same way as it does for an established fault.

The application should be coordinated with:

  • Circuit-breaker closing logic
  • Dead-line and live-line conditions
  • Auto-reclosing
  • Distance protection trip logic
  • Circuit-breaker status signals

14. Backup Overcurrent Protection

In addition to distance protection, REL650 provides backup current protection functions.

These functions provide additional protection when distance protection is unavailable, blocked or does not operate as expected.

14.1 Instantaneous phase overcurrent protection

PHPIOC – Instantaneous Phase Overcurrent Protection

This function detects high phase currents and can provide fast fault protection.

It is commonly used for backup protection or specific high-current applications.

14.2 Four-step phase overcurrent protection

OC4PTOC – Four-Step Phase Overcurrent Protection

This function provides multiple stages of phase overcurrent protection.

Depending on the selected settings, the stages can be configured with different current thresholds and operating delays.

Directional operation requires the relevant voltage polarization and configuration.

14.3 Instantaneous residual overcurrent protection

EFPIOC – Instantaneous Residual Overcurrent Protection

This function detects residual current associated with earth faults.

It can provide fast earth-fault protection when the residual current exceeds the configured threshold.

14.4 Four-step residual overcurrent protection

EF4PTOC – Four-Step Residual Overcurrent Protection

This function provides multiple stages of residual overcurrent protection.

Directional earth-fault operation can be applied where the required voltage or current polarization is available and configured.

15. Additional Protection and Supervision Functions

The REL650 product guide describes several additional functions.

FunctionANSI referenceApplication
PHPIOC50Instantaneous phase overcurrent
OC4PTOC51 / 67Four-step phase overcurrent
EFPIOC50NInstantaneous residual overcurrent
EF4PTOC51N / 67NFour-step residual overcurrent
CCRBRF50BFCircuit-breaker failure protection
CCPDSC52PDPole discordance protection
UV2PTUV27Two-step undervoltage protection
CVGAPCApplication-dependentGeneral current and voltage protection
ZMRPSB68Power swing detection
OOSPPAM78Out-of-step protection

The table is a functional overview, not a guarantee that every function is available in every ordering configuration.

16. Circuit-Breaker Failure Protection

Circuit-breaker failure protection is important for isolating faults when the circuit-breaker does not interrupt the fault current after receiving a trip command.

The REL650 includes:

CCRBRF – Circuit-Breaker Failure Protection

The function can supervise the trip command and current conditions.

If the breaker fails to clear the fault within the configured time, the protection scheme can initiate backup tripping of other breakers.

Important settings and signals include:

  • Breaker-failure initiation
  • Current detection threshold
  • Retrip logic
  • Backup trip delay
  • Circuit-breaker auxiliary contacts
  • Trip circuit supervision
  • Reset conditions
  • Coordination with busbar protection

The complete breaker-failure scheme should be tested, including the external trip circuits and the breakers that receive the backup trip command.

17. Auto-Reclosing and Synchronism Check

Auto-reclosing is widely used on overhead transmission lines because many line faults are temporary.

After a protection trip, the auto-reclosing function can initiate a closing operation after a configured dead time.

The REL650 application includes auto-reclosing and synchronism-check capabilities, depending on the selected configuration.

Important parameters include:

  • Single-phase or three-phase reclosing
  • Dead time
  • Reclaim time
  • Reclosing shot sequence
  • Circuit-breaker readiness
  • Synchronism-check conditions
  • Dead-line and live-line conditions
  • Reclosing blocking signals

Synchronism check

Before closing a circuit-breaker between two energized systems, the synchronism-check function verifies conditions such as:

  • Voltage magnitude difference
  • Phase angle difference
  • Frequency difference
  • Voltage availability

The synchronism-check function helps prevent closing under unsuitable electrical conditions.

The protection engineer must coordinate auto-reclosing with the circuit-breaker arrangement, remote-end protection and station control system.

18. CT and VT Requirements

Accurate current and voltage measurements are essential for distance protection.

Current transformer checks

The commissioning engineer should verify:

  • CT ratio
  • CT polarity
  • CT secondary rating
  • CT accuracy class
  • CT burden
  • CT saturation performance
  • Phase identification
  • Residual current connection

Voltage transformer checks

The following should be verified:

  • VT ratio
  • VT polarity
  • Phase sequence
  • Secondary earthing
  • Voltage input configuration
  • Residual voltage measurement
  • Fuse failure supervision

Incorrect CT or VT wiring can result in incorrect impedance measurement and unwanted protection operation.

19. Line Impedance Calculations and Settings

Accurate line data is essential for distance protection.

The protection engineer should obtain the following parameters:

  • Positive-sequence resistance (R1)
  • Positive-sequence reactance (X1)
  • Zero-sequence resistance (R0)
  • Zero-sequence reactance (X0)
  • Line length
  • System frequency
  • CT ratio
  • VT ratio
  • Mutual coupling data, where applicable

Important distance protection settings

SettingPurpose
Zone 1 reachDefines primary instantaneous protection coverage
Zone 2 reachProvides extended, time-delayed protection
Zone 3 reachProvides remote backup coverage where applied
Zone directionDefines forward or reverse operation
Resistive reachDefines resistance coverage
Reactive reachDefines reactance coverage
Zone operating timeCoordinates distance zones with adjacent protection
Earth-fault compensationCorrects earth-fault impedance measurement
Load encroachmentHelps prevent operation during heavy loading
Power swing settingsSupervises distance protection during power swings

The final settings should be verified through a protection coordination study and the applicable ABB application guidance.

ABB REL650 line distance protection relay front panel ABB Relion REL650 A11 protection IED ABB REL650 relay rear terminals and hardware ABB REL650 transmission line protection panel Six-zone distance protection impedance diagram ABB PCM600 REL650 configuration

20. PCM600 Engineering and Configuration

ABB PCM600 – Protection and Control IED Manager is used for engineering and configuration of compatible ABB Relion IEDs.

Typical REL650 engineering activities include:

  1. Create a new PCM600 project.
  2. Add the REL650 IED.
  3. Select the correct product version and connectivity package.
  4. Verify the hardware configuration.
  5. Configure the analog inputs.
  6. Enter CT and VT ratios.
  7. Configure the distance protection function.
  8. Enter line impedance data.
  9. Configure backup protection functions.
  10. Configure trip and circuit-breaker logic.
  11. Configure auto-reclosing and synchronism check.
  12. Configure IEC 61850 communication.
  13. Validate the configuration.
  14. Download the configuration to the IED.
  15. Verify the final operation.

The PCM600 version and connectivity package must be compatible with the installed REL650 product version.

Application configuration

The application configuration is used to connect protection functions with the relevant signals and logic.

Examples include:

  • Distance protection start signals
  • Distance protection trip signals
  • Circuit-breaker status
  • Auto-reclosing initiation
  • Circuit-breaker failure initiation
  • GOOSE input signals
  • Binary input and output assignments

The engineer should document and verify the complete signal path from measurement to protection operation and final trip output.

21. IEC 61850 Communication in REL650

REL650 supports IEC 61850-based substation automation integration, subject to the installed product version and communication configuration.

IEC 61850 provides standardized communication between protection IEDs, bay controllers and station-level systems.

Typical applications include:

  • MMS communication
  • GOOSE communication
  • SCL engineering
  • Protection status monitoring
  • Breaker status exchange
  • Interlocking signals
  • Event and alarm reporting
  • Integration with SCADA systems

21.1 IEC 61850 MMS

MMS communication is commonly used for monitoring, control and reporting between the IED and the station-level system.

Typical information includes:

  • Protection start and trip indications
  • Circuit-breaker status
  • Measurement values
  • Alarms
  • Events
  • Disturbance information

21.2 IEC 61850 GOOSE

GOOSE communication allows fast peer-to-peer exchange of signals between IEDs.

Possible applications include:

  • Interlocking
  • Circuit-breaker status exchange
  • Protection scheme signals
  • Direct transfer signals
  • Trip-related logic
  • Communication-assisted applications

The actual application must be engineered and tested.

21.3 SCL configuration

Substation Configuration Language files are used to exchange engineering information between compatible IEC 61850 tools.

A typical engineering workflow includes:

  1. Configure the REL650 in PCM600.
  2. Define the required IEC 61850 data.
  3. Export the relevant SCL file.
  4. Integrate the IED into the station configuration.
  5. Configure GOOSE publishers and subscribers.
  6. Import the updated configuration where required.
  7. Verify communication and signal mapping.
  8. Test the complete application.

22. Testing and Commissioning of REL650

Testing should cover the protection functions, application logic, circuit-breaker interfaces and communication system.

22.1 Visual and wiring inspection

Before applying test signals, verify:

  • Relay model and ordering information
  • Auxiliary DC supply
  • CT wiring
  • VT wiring
  • Binary input wiring
  • Binary output wiring
  • Trip circuit
  • Circuit-breaker auxiliary contacts
  • Communication connections
  • Earthing and panel wiring

22.2 Secondary injection testing

An OMICRON CMC test set with suitable Test Universe modules can be used for secondary injection testing.

Typical tests include:

  • Current measurement
  • Voltage measurement
  • Phase rotation
  • Distance protection reach
  • Distance zone operating time
  • Quadrilateral characteristic
  • Mho characteristic
  • Earth-fault distance measurement
  • Directional operation
  • Phase selection
  • Load encroachment
  • Power swing logic
  • Overcurrent protection
  • Residual overcurrent protection
  • Circuit-breaker failure protection
  • Auto-reclosing
  • Synchronism check

22.3 Distance protection testing

For distance protection, apply test points inside and outside the configured protection zones.

Verify:

  • Correct impedance measurement
  • Correct operating direction
  • Zone reach
  • Zone operating time
  • Resistive boundary
  • Reactive boundary
  • Earth-fault compensation
  • Correct phase selection
  • Correct trip output

For a quadrilateral characteristic, test points should cover the resistive and reactive boundaries.

For a mho characteristic, verify the reach, directional response and operating boundary.

22.4 Auto-reclosing tests

The commissioning engineer should verify:

  • Initiation conditions
  • Dead time
  • Reclaim time
  • Reclosing sequence
  • Circuit-breaker readiness
  • Synchronism-check permission
  • Reclosing block conditions
  • Final circuit-breaker closing command

22.5 IEC 61850 tests

For IEC 61850 applications, verify:

  • MMS communication
  • GOOSE publishing
  • GOOSE subscription
  • Data mapping
  • Quality indications
  • Communication supervision
  • Correct operation of connected application logic

The complete protection scheme should be tested, not only the individual communication signals.

23. Common REL650 Problems and Troubleshooting

Problem 1: Incorrect distance measurement

Possible causes:

  • Incorrect CT ratio
  • Incorrect VT ratio
  • Incorrect phase connection
  • Incorrect line impedance data
  • Incorrect voltage or current polarity

Recommended checks: compare relay measurements with secondary injection measurements and verify all analog input settings.

Problem 2: Distance protection operates during heavy loading

Possible causes:

  • Incorrect zone reach
  • Incorrect load encroachment settings
  • Incorrect maximum load assumptions
  • Incorrect power swing supervision

Recommended checks: review the system loading study and verify the distance characteristic.

Problem 3: Earth-fault distance protection has incorrect reach

Possible causes:

  • Incorrect zero-sequence impedance
  • Incorrect earth-return compensation
  • Incorrect residual current measurement
  • CT wiring problems
  • Mutual coupling not considered

Recommended checks: verify the sequence impedance data and earth-fault compensation settings.

Problem 4: Auto-reclosing does not operate

Possible causes:

  • Incorrect initiation logic
  • Reclosing blocked by protection logic
  • Circuit-breaker not ready
  • Incorrect dead-time settings
  • Missing synchronism-check permission

Recommended checks: monitor the auto-reclosing sequence and verify all associated signals.

Problem 5: GOOSE communication does not operate

Possible causes:

  • Incorrect publisher configuration
  • Incorrect subscriber configuration
  • Incorrect dataset or control block
  • VLAN or priority mismatch
  • Incorrect communication mapping
  • Network communication problem

Recommended checks: inspect the SCL configuration and verify the GOOSE messages using suitable IEC 61850 engineering and diagnostic tools.

24. REL650 vs REL670 – Main Differences

Both REL650 and REL670 are ABB line distance protection IEDs, but they are intended for different application requirements.

FeatureREL650REL670
Main applicationLine distance protectionAdvanced line protection
Typical positioningSub-transmission applicationsTransmission applications
Distance protectionYesYes
Quadrilateral characteristicYesYes
Mho characteristicYesYes
Power swing functionsAvailable in documented configurationsAvailable in documented configurations
Auto-reclosingYesYes
Synchronism checkYesYes
IEC 61850YesYes
Series-compensated line applicationsCheck specific product capabilitiesDedicated advanced application capabilities documented
Application flexibilityPreconfigured application packagesMore extensive application flexibility in relevant configurations

The final relay selection should be based on the actual network requirements and the relevant ABB product documentation.

25. Frequently Asked Questions About ABB REL650

What is ABB REL650 used for?

ABB REL650 is a numerical line distance protection relay designed for overhead lines and cables in suitable solidly earthed or impedance-earthed networks.

What is the main protection function of REL650?

Its main protection function is distance protection, which measures apparent impedance to detect faults within configured protection zones.

Does REL650 support quadrilateral distance protection?

Yes. The REL650 distance protection function supports quadrilateral characteristics.

Does REL650 support mho distance protection?

Yes. The product documentation identifies both quadrilateral and mho distance characteristics.

How many distance protection zones does REL650 support?

The REL650 Version 2.2 documentation describes six distance protection zones with independent measuring and setting ranges.

Does REL650 support power swing detection?

Yes. The documented functions include ZMRPSB power swing detection and PSLPSCH power swing logic.

Does REL650 support out-of-step protection?

The REL650 Version 2.2 documentation lists OOSPPAM out-of-step protection.

Can REL650 perform single-phase tripping?

Yes. The REL650 A11 application is documented for single-phase tripping. Other application configurations provide different tripping arrangements.

Which software is used to configure REL650?

ABB PCM600 is used for engineering and configuration of compatible REL650 IEDs.

Does REL650 support IEC 61850?

Yes. REL650 supports IEC 61850 integration, subject to the installed product version and configuration.

Can REL650 be tested using OMICRON?

Yes. Suitable OMICRON CMC test equipment and Test Universe modules can be used for secondary injection and protection scheme testing.

26. Conclusion

The ABB REL650 is a line distance protection IED designed for overhead lines and cables in sub-transmission and other suitable network applications.

Its distance protection capabilities, quadrilateral and mho characteristics, power swing functions, backup protection, auto-reclosing and IEC 61850 communication make it a comprehensive solution for line protection.

For protection and commissioning engineers, practical knowledge of REL650 is important for correct configuration, distance zone calculations, protection coordination, PCM600 engineering, secondary injection testing and troubleshooting.

Elec-Engg – Practical Power System Protection and Substation Automation Training

Explore more technical articles and training resources covering ABB protection relays, PCM600, IEC 61850, distance protection and relay testing.


Related Articles

  • ABB REG670 Generator Protection Relay
  • ABB RET670 Transformer Protection Relay
  • ABB RED670 Line Differential Protection Relay
  • ABB REL670 Distance Protection Relay
  • ABB PCM600 Engineering Software – Complete Guide
  • Distance Protection – Operating Principle, Zones and Settings
  • IEC 61850 Communication in Protection Relays
  • Transmission Line Protection and Teleprotection Schemes

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top