GE Multilin 369 Motor Protection Relay: Complete Technical Guide to Thermal Overload, Motor Starting, Locked-Rotor Protection, Configuration and Testing

Table Of Contents
  1. 1. Introduction
  2. 2. GE Multilin 369 Relay Overview
  3. 3. Motor Protection Philosophy
  4. 4. Motor Nameplate Data and CT Configuration
  5. 5. Thermal Overload Protection – ANSI 49
  6. 6. Motor Starting Protection – ANSI 48
  7. 7. Locked-Rotor and Stall Protection
  8. 8. Starts-Per-Hour Protection – ANSI 66
  9. 9. Phase Overcurrent Protection – ANSI 50/51
  10. 10. Earth-Fault Protection
  11. 11. Negative-Sequence Protection – ANSI 46
  12. 12. Undercurrent Protection – ANSI 37
  13. 13. Voltage Protection – ANSI 27 and 59
  14. 14. RTD Temperature Monitoring
  15. 15. Motor Protection Coordination
  16. 16. GE Multilin 369 Configuration Using EnerVista
  17. 17. Testing and Commissioning of the GE Multilin 369
  18. 18. Troubleshooting Common GE Multilin 369 Problems
  19. 19. Practical Commissioning Checklist
  20. 20. GE Multilin 369 Compared with Other GE Motor Protection Relays
  21. 21. Common Motor Protection Engineering Mistakes
  22. 22. Training on GE Multilin Motor Protection Relays by Elec-Engg
  23. 23. Conclusion
  24. 24. Frequently Asked Questions

1. Introduction

The GE Multilin 369 Motor Protection Relay is designed to protect and monitor medium-voltage and selected industrial motor applications. It combines motor protection functions with monitoring, event recording, control and communication capabilities, depending on the installed hardware and firmware configuration.

Motor protection requires a different engineering approach from ordinary feeder protection. A motor draws a significant starting current, experiences thermal stress during acceleration, and may be damaged by conditions such as phase loss, mechanical overload, locked rotor, excessive starts and unbalanced supply voltage.

The GE Multilin 369 is intended to help engineers detect these abnormal conditions and initiate alarms or trips according to the motor’s operating requirements.

This article covers:

  • GE Multilin 369 architecture and applications
  • Motor nameplate data and CT configuration
  • Thermal overload protection (ANSI 49)
  • Motor starting and acceleration supervision (ANSI 48)
  • Locked-rotor and stall protection
  • Starts-per-hour supervision (ANSI 66)
  • Phase overcurrent and earth-fault protection
  • Negative-sequence protection (ANSI 46)
  • Undercurrent and mechanical load monitoring
  • RTD temperature monitoring
  • Motor protection settings and coordination
  • EnerVista configuration
  • Secondary injection and functional testing
  • Troubleshooting and commissioning

The objective is to provide a practical engineering reference for protection, commissioning, operation and maintenance engineers.

2. GE Multilin 369 Relay Overview

The GE Multilin 369 is a motor protection relay intended for industrial motor applications. It is used to monitor electrical and thermal conditions that could damage a motor or associated equipment.

Typical applications include:

  • Medium-voltage induction motors
  • Industrial pumps
  • Fans and blowers
  • Compressors
  • Conveyors
  • Crushers and mills
  • Process plant motors
  • Motors operating in demanding starting and loading conditions

The protection philosophy must consider both the electrical supply and the mechanical characteristics of the driven equipment.

A motor may experience an electrical fault, such as a phase-to-phase short circuit, or a mechanical problem, such as a jammed pump or conveyor. Both can produce abnormal current or thermal conditions.

The exact protection functions, communication options, RTD inputs, control capabilities and hardware options must be checked against the installed 369 model, order code and firmware.

3. Motor Protection Philosophy

A motor protection scheme must protect the motor without unnecessarily tripping it during normal starting and operating conditions.

The most important motor operating conditions include:

  1. Normal running.
  2. Motor acceleration.
  3. Short-duration overload.
  4. Prolonged overload.
  5. Locked rotor.
  6. Excessive starting frequency.
  7. Phase unbalance.
  8. Phase loss.
  9. Earth fault.
  10. Abnormal winding or bearing temperature.
  11. Loss of mechanical load.
  12. Abnormal supply voltage.

Motor protection must be coordinated with:

  • Motor thermal withstand characteristics
  • Starting current
  • Starting time
  • Hot and cold stall limits
  • Starts-per-hour limitations
  • Contactor or circuit-breaker capability
  • Upstream feeder protection
  • Process requirements

A protection setting that is too sensitive may trip the motor during normal acceleration. A setting that is too insensitive may allow damaging thermal stress to continue.

4. Motor Nameplate Data and CT Configuration

Before configuring a motor relay, engineers should collect the motor nameplate and application data.

Important information includes:

  • Rated output power
  • Rated voltage
  • Rated current
  • Rated frequency
  • Power factor
  • Efficiency
  • Rated speed
  • Service factor, where applicable
  • Starting current
  • Starting time
  • Insulation class
  • Permitted starts per hour
  • Locked-rotor withstand time
  • Cooling arrangement
  • Temperature sensor information

4.1 Motor Rated Current Calculation

For a three-phase motor:

[
I=\frac{P}{\sqrt{3}\times V\times PF\times \eta}
]

Where:

  • (P) = motor output power in watts
  • (V) = line-to-line voltage
  • (PF) = power factor
  • (\eta) = efficiency

Consider an illustrative motor with:

ParameterValue
Rated output500 kW
Voltage4.16 kV
Power factor0.86
Efficiency0.94

The rated current is:

[
I=\frac{500000}{\sqrt{3}\times4160\times0.86\times0.94}
]

[
I\approx90.7\ A
]

The calculated value should be compared with the manufacturer’s nameplate current. The nameplate value should normally be used as the primary reference for motor protection settings.

4.2 CT Ratio Selection

Assume the motor feeder uses a CT ratio of 100/1 A.

The current at rated motor load is:

[
I_s=\frac{90.7}{100}=0.907\ A
]

The relay therefore measures approximately 0.907 A at rated motor current, assuming a correctly configured 1 A input and ideal CT behaviour.

The engineer must verify:

  • CT primary rating
  • CT secondary rating
  • Relay current-input rating
  • CT accuracy class
  • CT burden
  • Short-circuit thermal rating
  • CT saturation performance
  • Correct phase assignment and polarity

Do not assume that all 369 configurations use identical current-input hardware.

5. Thermal Overload Protection – ANSI 49

Thermal overload protection is one of the most important motor protection functions.

A motor can be damaged when its winding temperature exceeds the permitted thermal limit. Excessive current produces additional heating in the stator and rotor.

The thermal condition depends on:

  • Motor current
  • Duration of overload
  • Previous loading
  • Cooling conditions
  • Ambient temperature
  • Starting frequency
  • Rotor and stator thermal characteristics

5.1 Basic Thermal Heating Principle

The heating effect of current is approximately proportional to:

[
P_{\text{loss}}=I^2R
]

If current increases, copper losses increase approximately with the square of current, assuming resistance remains constant.

For example, if motor current rises to 1.5 times rated current:

[
\frac{P_{\text{loss}}}{P_{\text{rated}}}=1.5^2=2.25
]

The current-dependent copper losses are therefore approximately 2.25 times their rated-current value.

This explains why prolonged overloads can cause rapid temperature rise.

5.2 Thermal Model

A numerical motor protection relay may use a thermal model to estimate motor heating and cooling.

A simplified first-order thermal relationship can be expressed as:

[
\frac{d\theta}{dt}=
\frac{\theta_{\text{steady}}-\theta}{\tau}
]

Where:

  • (\theta) = estimated thermal state
  • (\theta_{\text{steady}}) = thermal state corresponding to the present loading
  • (\tau) = thermal time constant

The actual GE Multilin thermal model may use additional parameters and motor-specific algorithms. The simplified equation is intended to explain the principle, not reproduce the complete relay algorithm.

5.3 Thermal Memory

Thermal memory is important because a motor does not immediately return to a cold condition after a trip.

If a motor is stopped after an overload, its winding and rotor may remain hot. Restarting too soon can exceed the motor’s thermal withstand limit.

The engineer should therefore consider:

  • Hot and cold thermal limits
  • Heating time constant
  • Cooling time constant
  • Thermal capacity
  • Restart inhibition
  • Thermal reset conditions

The actual parameters and available thermal model options must be verified in the 369 documentation.

6. Motor Starting Protection – ANSI 48

During starting, an induction motor draws a current significantly higher than its normal running current.

The starting current depends on:

  • Motor design
  • Supply voltage
  • Starting method
  • Mechanical load
  • Motor inertia
  • System impedance

The relay must distinguish between a normal starting condition and an abnormal starting event.

6.1 Starting Current

A motor may draw several times its rated current during direct-on-line starting. The exact value must be obtained from the motor manufacturer’s data.

For example, if a motor rated current is 90.7 A and the starting current is six times rated current:

[
I_{\text{start}}=6\times90.7
]

[
I_{\text{start}}=544.2\ A
]

With a 100/1 CT:

[
I_{\text{start,secondary}}=\frac{544.2}{100}
]

[
I_{\text{start,secondary}}=5.442\ A
]

This is the approximate secondary current presented to the relay during starting, assuming the CT and input are within their applicable operating limits.

6.2 Acceleration Time

The motor must accelerate to its normal operating speed within an acceptable time.

The acceleration time depends on:

  • Motor torque-speed characteristic
  • Load torque
  • Combined motor and load inertia
  • Supply voltage
  • Starting method

The protection setting must allow normal acceleration but detect abnormal prolonged starting.

6.3 Starting Supervision

Starting supervision can use current and time information to determine whether the motor is starting normally.

The engineer should compare:

  • Expected starting current
  • Expected acceleration time
  • Motor hot and cold stall limits
  • Starting frequency restrictions
  • Relay thermal model behaviour

A generic starting protection setting should never be copied from another motor without checking the motor data.

7. Locked-Rotor and Stall Protection

A locked-rotor condition occurs when the motor cannot accelerate or when a running motor becomes mechanically blocked.

Possible causes include:

  • Jammed pump
  • Blocked conveyor
  • Mechanical seizure
  • Bearing failure
  • Excessive driven load
  • Coupling failure
  • Incorrect starting conditions

A locked rotor can cause high current and severe thermal stress.

7.1 Starting Locked Rotor

If the motor remains at standstill while drawing starting current, the rotor may heat rapidly.

The protection scheme must detect a starting condition that exceeds the permitted acceleration time or thermal withstand limit.

7.2 Running Stall

A motor may accelerate successfully and later become mechanically blocked.

Running stall protection must distinguish between normal load increase and a dangerous mechanical stall.

The exact available stall and starting supervision functions should be checked against the installed 369 configuration.

8. Starts-Per-Hour Protection – ANSI 66

Motor manufacturers commonly specify a maximum number of starts within a given time period.

Repeated starting produces thermal stress because each start involves elevated current and heating.

The permitted starting frequency depends on:

  • Motor design
  • Starting method
  • Load inertia
  • Initial motor temperature
  • Cooling conditions
  • Time between starts

For example, a motor may be permitted to perform only a limited number of starts from a cold condition and fewer starts from a hot condition.

The protection scheme should prevent a new start when the motor has exceeded its permitted starting frequency or thermal condition.

Where supported, the 369 can be configured to supervise starting frequency and restart conditions.

9. Phase Overcurrent Protection – ANSI 50/51

Phase overcurrent protection provides protection against high-current faults and can provide backup protection against abnormal motor current.

9.1 Instantaneous Overcurrent – ANSI 50

Instantaneous overcurrent protection can detect high-current short-circuit conditions.

The pickup must be coordinated with:

  • Motor starting current
  • CT performance
  • Feeder short-circuit level
  • Downstream protection
  • Breaker or contactor interrupting capability

The instantaneous setting must not cause unwanted operation during normal motor starting.

9.2 Time Overcurrent – ANSI 51

Time overcurrent protection can provide backup protection against sustained overcurrent conditions.

It may be coordinated with the motor thermal protection model and upstream feeder protection.

The motor’s thermal overload function and phase overcurrent elements should be engineered as parts of one coordinated scheme.

10. Earth-Fault Protection

Earth faults can occur because of insulation deterioration, moisture, cable damage, contamination or winding insulation failure.

Depending on the installed configuration, earth-fault protection may use residual current measurement or a separate earth-fault CT.

10.1 Residual Current

The residual current is:

[
I_{\text{res}}=I_A+I_B+I_C
]

Under balanced operating conditions:

[
I_{\text{res}}\approx0
]

During an earth fault, the residual current may increase.

10.2 Core-Balance CT

A core-balance CT surrounding all three motor feeder conductors can provide sensitive earth-fault detection.

The CT installation must ensure that all phase conductors pass through the core in the correct arrangement. The protective earth conductor should not be included in the same measurement path in a way that cancels the residual current being detected.

10.3 Earth-Fault Setting Considerations

The pickup must consider:

  • System neutral earthing
  • Motor cable capacitance
  • Expected earth-fault current
  • CT ratio and sensitivity
  • Starting and transient conditions
  • Downstream protection coordination

The relay’s supported earth-fault inputs and functions must be verified before preparing the wiring design.

11. Negative-Sequence Protection – ANSI 46

Negative-sequence current indicates phase unbalance.

Common causes include:

  • Single-phasing
  • Unequal phase loading
  • Unbalanced supply voltage
  • Loose connections
  • Open conductors
  • Faults in the supply system

Negative-sequence current produces additional heating in the rotor of an induction motor.

A motor can therefore experience dangerous heating even when the average phase current does not appear excessively high.

11.1 Symmetrical Components

Three-phase currents can be resolved into:

  • Positive-sequence current (I_1)
  • Negative-sequence current (I_2)
  • Zero-sequence current (I_0)

The negative-sequence component represents the unbalanced portion that rotates in the opposite direction to the positive-sequence component.

11.2 Negative-Sequence Thermal Effect

A simplified thermal relationship is:

[
H\propto I_2^2t
]

Where:

  • (I_2) = negative-sequence current
  • (t) = duration
  • (H) = accumulated heating effect

The actual motor thermal withstand relationship is manufacturer-dependent.

Engineers should use the motor manufacturer’s negative-sequence withstand data and the relay’s documented protection characteristic.

12. Undercurrent Protection – ANSI 37

Undercurrent protection detects a reduction in motor current below a configured threshold.

It can be useful for detecting mechanical or process conditions such as:

  • Pump running dry
  • Loss of pump load
  • Broken coupling
  • Loss of driven equipment
  • Reduced process demand

However, low current is not always a fault. The engineer must understand the normal operating range of the driven equipment.

For example, a pump may naturally draw less current when operating at reduced flow. The protection setting must distinguish this normal condition from a genuine loss-of-load event.

13. Voltage Protection – ANSI 27 and 59

Where supported by the installed configuration, voltage protection can detect abnormal supply voltage conditions.

13.1 Undervoltage – ANSI 27

Undervoltage may cause:

  • Increased motor current for certain operating conditions
  • Reduced torque
  • Longer acceleration time
  • Motor stalling
  • Contactor dropout

13.2 Overvoltage – ANSI 59

Overvoltage may increase insulation stress and affect motor operating conditions.

Voltage protection should be coordinated with the plant supply philosophy and motor manufacturer’s permitted operating range.

The engineer must verify whether the required VT inputs and voltage elements are available in the specific relay configuration.

14. RTD Temperature Monitoring

Temperature monitoring can provide additional protection for motor components.

Depending on the hardware configuration, motor RTDs may be installed in:

  • Stator windings
  • Bearing locations
  • Motor frame
  • Cooling air paths

Common sensor types include resistance temperature detectors such as Pt100, although the actual sensor and input compatibility must be confirmed.

14.1 RTD Alarm and Trip Levels

A typical temperature protection philosophy may include:

  • Warning alarm
  • High-temperature alarm
  • Trip threshold

The actual values must be selected from the motor manufacturer’s temperature limits and the sensor installation design.

14.2 RTD Wiring Checks

During commissioning, verify:

  • Sensor type
  • Input compatibility
  • Wiring arrangement
  • Lead compensation
  • Sensor identification
  • Correct temperature indication
  • Open-circuit and short-circuit detection, where supported

Do not apply an RTD simulation method unless it is compatible with the relay’s specific input design.

15. Motor Protection Coordination

Motor protection must coordinate with the upstream feeder and short-circuit protection.

The protection engineer should review:

  1. Motor full-load current.
  2. Starting current and duration.
  3. Hot and cold stall withstand times.
  4. Thermal overload characteristic.
  5. Cable thermal withstand.
  6. Contactor or circuit-breaker rating.
  7. Short-circuit protection.
  8. Earth-fault protection.
  9. Upstream protection coordination.
  10. Process requirements.

15.1 Example of Starting Current and Pickup

Using the illustrative motor from Section 4:

  • Rated current: 90.7 A
  • CT ratio: 100/1 A
  • Starting current: 544.2 A
  • Starting-current multiple: 6 times rated current

A protection element intended to remain stable during normal starting must be checked against the actual starting current and duration.

The phase short-circuit element should be set high enough to avoid unwanted operation during normal starting, while still detecting the required fault-current range.

The thermal overload function must separately protect against excessive heating during prolonged starting or overload conditions.

There is no universal pickup value suitable for all motors.

16. GE Multilin 369 Configuration Using EnerVista

The applicable GE Multilin EnerVista software is used for supported relay configuration, monitoring and settings management.

The exact software version must be compatible with the relay model and firmware.

Step 1 – Identify the Relay

Record:

  • Model and order code
  • Serial number
  • Firmware version
  • Hardware configuration
  • Communication interfaces

Step 2 – Retrieve the Existing Configuration

Where supported, connect to the relay and retrieve the existing settings.

Save the original configuration before making changes.

Step 3 – Enter Motor Nameplate Data

Configure the motor information required by the relay, such as:

  • Rated current
  • Rated voltage
  • Frequency
  • Starting information
  • Thermal data
  • CT information
  • Other application-specific parameters

The exact parameters available depend on the relay version.

Step 4 – Configure Current and Voltage Inputs

Verify CT ratios, input ratings, phase assignments and any VT configuration.

Compare relay measurements against independent test equipment.

Step 5 – Configure Thermal Protection

Enter the motor thermal parameters using manufacturer data and the applicable relay model.

Review:

  • Thermal overload settings
  • Thermal memory
  • Heating and cooling characteristics
  • Hot and cold starting limits
  • Restart restrictions

Step 6 – Configure Starting and Stall Protection

Configure the supported starting supervision functions using the motor’s actual acceleration time and locked-rotor withstand information.

Step 7 – Configure Other Protection Functions

Review applicable elements such as:

  • Phase overcurrent
  • Earth fault
  • Negative sequence
  • Undercurrent
  • Voltage protection
  • RTD monitoring
  • Starts-per-hour supervision

Only configure functions supported by the specific relay.

Step 8 – Configure Trip Logic and Outputs

Map the required protection operations to alarms, trip outputs and external control signals.

Verify the complete trip path.

Step 9 – Review, Save and Document

Check all settings against the approved motor protection study.

Save the final configuration and maintain a revision-controlled backup.

17. Testing and Commissioning of the GE Multilin 369

A complete commissioning process should test measurements, protection elements, logic, outputs and the motor trip circuit.

17.1 Preliminary Checks

Before testing:

  • Verify relay identification.
  • Confirm auxiliary supply.
  • Inspect CT and VT wiring.
  • Verify RTD wiring, where installed.
  • Confirm settings and firmware.
  • Check trip circuit isolation.
  • Review motor and equipment documentation.
  • Apply approved safety procedures.

17.2 Current Measurement Test

Inject balanced three-phase currents and verify:

  • Phase A current
  • Phase B current
  • Phase C current
  • Current scaling
  • Phase sequence
  • Residual current

Confirm that relay measurements agree with the injection equipment within the applicable tolerances.

17.3 Thermal Overload Test

A thermal overload test should verify the relay’s response to the configured thermal model.

Depending on the relay and test equipment, the procedure may include:

  1. Establishing a known thermal state.
  2. Applying current above the thermal pickup region.
  3. Monitoring thermal capacity or equivalent indication, where available.
  4. Recording the operating time.
  5. Verifying the trip output.
  6. Checking thermal reset and cooling behaviour.

Thermal model testing must account for thermal memory. Repeating tests without allowing the model to reset can produce misleading results.

17.4 Starting and Stall Tests

Verify that the relay distinguishes between acceptable starting and abnormal prolonged starting.

Test scenarios may include:

  • Normal starting profile
  • Starting current above the expected range
  • Acceleration exceeding the configured limit
  • Running stall condition, where applicable
  • Restart inhibition

The test should reproduce the intended operating conditions without unnecessarily stressing the actual motor.

17.5 Negative-Sequence Test

Inject an unbalanced three-phase current set and verify the negative-sequence measurement and element response.

Check:

  • Pickup
  • Timing
  • Reset
  • Alarm
  • Trip output

17.6 Earth-Fault Test

Test the configured earth-fault measurement arrangement.

For residual measurement, inject the required unbalanced current combination.

For a dedicated earth-fault input, test the input using the appropriate secondary injection connection.

Verify the correct element operation and output mapping.

17.7 RTD Test

Where RTD inputs are installed, use a compatible temperature simulator.

Verify:

  • Temperature measurement
  • Alarm threshold
  • Trip threshold
  • Sensor fault indication
  • Input identification

17.8 Binary Input and Output Test

Verify:

  • Start command
  • Stop command
  • Breaker or contactor status
  • External interlocks
  • Trip output
  • Alarm output
  • Reset functions

17.9 Complete Trip Circuit Test

The final test should confirm that the relay can operate the intended trip circuit.

Check:

  • Relay output contact
  • Interposing relay, if installed
  • Trip coil
  • Contactor or circuit-breaker mechanism
  • Auxiliary feedback
  • Trip indication
  • Event records

Follow the site’s approved procedures for isolation and controlled operation.

18. Troubleshooting Common GE Multilin 369 Problems

ProblemPossible causesEngineering checks
Motor trips during startingStarting time or thermal settings incorrectCompare starting current and acceleration time with motor data
Motor thermal alarm during normal operationIncorrect rated current or thermal parametersVerify nameplate and CT scaling
Incorrect current measurementCT ratio or phase wiring errorCheck CT ratio, polarity and phase assignment
Unexpected earth-fault alarmResidual wiring or CT problemVerify phase CT connections and dedicated earth-fault input
Negative-sequence alarmActual unbalance or incorrect current measurementCheck supply voltage, phase currents and CT wiring
Motor restart inhibitedThermal memory or start limitation activeReview thermal state and starts-per-hour settings
RTD alarmSensor, wiring or configuration problemCheck sensor type and input compatibility
Undercurrent tripPickup unsuitable for process operationReview normal load range and process characteristics
Relay does not trip contactorOutput mapping or trip circuit issueTrace the complete trip path
Communication failureInterface or software compatibility issueCheck connection, protocol and firmware support

Always use the relay’s actual measured values, element status and event records when diagnosing problems.

19. Practical Commissioning Checklist

Relay and Hardware

  • Correct GE Multilin 369 model and order code
  • Firmware and software compatibility checked
  • Auxiliary supply verified
  • CT wiring and polarity checked
  • VT wiring checked, where applicable
  • RTD wiring checked, where installed
  • Binary input/output wiring verified

Motor Data

  • Motor nameplate recorded
  • Rated current confirmed
  • Starting current confirmed
  • Acceleration time confirmed
  • Hot and cold stall limits obtained
  • Starts-per-hour limitation confirmed
  • Thermal information obtained from manufacturer

Protection Settings

  • Thermal overload settings reviewed
  • Starting supervision reviewed
  • Stall protection reviewed
  • Phase overcurrent settings reviewed
  • Earth-fault settings reviewed
  • Negative-sequence protection reviewed
  • Undercurrent settings reviewed
  • RTD alarm and trip levels reviewed
  • Trip logic verified

Testing and Documentation

  • Current measurement tests completed
  • Thermal model tested
  • Starting and stall logic tested
  • Earth-fault protection tested
  • Negative-sequence protection tested
  • RTD inputs tested, where installed
  • Binary inputs and outputs tested
  • Motor trip circuit verified
  • Final settings archived
  • Commissioning report completed

20. GE Multilin 369 Compared with Other GE Motor Protection Relays

GE Multilin provides several motor protection products for different industrial applications.

RelayGeneral application
GE Multilin 369Motor protection and monitoring
GE Multilin 339Motor protection applications
GE Multilin 469Advanced motor protection and management applications
GE Multilin 859Compact motor protection applications
GE Multilin 869Motor protection applications

The appropriate relay depends on motor criticality, required protection functions, measurement needs, RTD requirements, communication architecture and project specifications.

This table is a general product-family comparison, not a statement that the relays have identical functions or hardware.

21. Common Motor Protection Engineering Mistakes

The following errors can result in unwanted trips or inadequate motor protection:

  1. Using calculated motor current instead of verifying the nameplate current.
  2. Ignoring CT ratio and secondary input rating.
  3. Setting thermal overload protection without motor thermal data.
  4. Ignoring hot and cold stall withstand times.
  5. Setting starting supervision without checking acceleration time.
  6. Failing to consider repeated starting.
  7. Ignoring negative-sequence heating.
  8. Using earth-fault settings without considering system earthing.
  9. Setting undercurrent protection without understanding the driven process.
  10. Ignoring RTD sensor type and wiring.
  11. Testing individual protection elements without checking the complete trip circuit.
  12. Copying settings from another motor with different mechanical and electrical characteristics.

22. Training on GE Multilin Motor Protection Relays by Elec-Engg

Practical motor protection engineering requires a combination of electrical protection knowledge, motor application understanding, settings calculation, software configuration and testing experience.

Elec-Engg provides practical technical training by Dr Saeed Roostaee (Electrical Engineering) for engineers working in power system protection, industrial electrical systems, commissioning and maintenance.

Relevant training topics include:

  • GE Multilin motor protection relays
  • GE 369 motor protection principles
  • Thermal overload protection
  • Motor starting and acceleration supervision
  • Locked-rotor and stall protection
  • Starts-per-hour protection
  • Negative-sequence protection
  • Earth-fault protection
  • RTD temperature monitoring
  • Motor protection coordination
  • EnerVista configuration
  • Secondary injection testing
  • Troubleshooting and commissioning

Training delivery options include:

  • Pre-recorded video courses
  • Structured self-paced training
  • Live online training
  • Face-to-face technical training
  • Customized in-house training for companies and utilities

The training focuses on practical engineering applications, helping engineers understand not only how protection functions operate but also how to configure, test and troubleshoot them in real projects.

Explore technical training resources at:

Website: https://elec-engg.com/

Contact: https://elec-engg.com/contact/

23. Conclusion

The GE Multilin 369 is a motor protection relay intended to protect industrial motors against electrical and thermal operating conditions that may lead to equipment damage.

Its application requires accurate motor data, correct CT configuration, appropriate thermal modelling, reliable starting supervision and coordination with the motor feeder protection system.

Particular attention should be given to starting current, acceleration time, locked-rotor withstand, thermal memory and repeated-start limitations.

A successful commissioning process must verify not only the individual protection elements but also the complete control and trip circuit.

For engineers responsible for industrial motor protection, understanding the motor characteristics and the relay’s actual capabilities is essential to achieving reliable protection and minimizing unnecessary production interruptions.

24. Frequently Asked Questions

1. What is the GE Multilin 369 relay used for?

The GE Multilin 369 is used for industrial motor protection and monitoring. Its application may include thermal overload, starting supervision, current-based protection and other motor-related functions depending on the configuration.

2. What is ANSI 49 motor protection?

ANSI 49 is thermal overload protection. It estimates or monitors motor thermal stress and initiates an alarm or trip when the configured thermal limit is reached.

3. Why is motor thermal memory important?

Thermal memory accounts for the heat accumulated during previous operation. It helps prevent a motor from restarting while it is still too hot.

4. What is locked-rotor protection?

Locked-rotor protection detects a condition where the motor cannot accelerate or becomes mechanically blocked. Prolonged high current can rapidly damage the rotor and stator.

5. What information is required to configure a GE Multilin 369?

Important information includes motor rated current, voltage, starting current, acceleration time, hot and cold stall limits, CT ratios, thermal data and the system protection study.

6. How is the GE Multilin 369 tested?

Testing generally includes current measurement verification, thermal overload tests, starting and stall tests, negative-sequence tests, earth-fault tests, RTD tests where applicable, binary I/O checks and complete trip circuit verification.

7. Can the GE Multilin 369 monitor motor temperature?

Temperature monitoring depends on the installed hardware and supported sensor inputs. Check the exact relay documentation before designing an RTD monitoring scheme.

8. What is the difference between the GE Multilin 369 and 469?

Both are associated with motor protection applications, but their hardware, protection functions and management capabilities differ. The exact comparison should be made using the relevant product documentation and order codes.

9. Why does a motor protection relay trip during starting?

Possible reasons include excessive starting time, incorrect thermal parameters, unsuitable current settings, abnormal supply voltage, mechanical loading or a genuine motor starting problem.

10. Where can engineers receive GE Multilin motor protection training?

Elec-Engg provides practical power system protection and numerical relay training by Dr Saeed Roostaee (Electrical Engineering). Visit https://elec-engg.com/ or contact https://elec-engg.com/contact/ for further information.


Suggested SEO focus keyphrase: GE Multilin 369 Motor Protection Relay

Suggested SEO title: GE Multilin 369 Motor Protection Relay: Settings, Configuration and Testing

Suggested URL slug: ge-multilin-369-motor-protection-relay

Suggested meta description: Complete technical guide to GE Multilin 369 motor protection, thermal overload, motor starting, locked rotor, negative sequence, EnerVista configuration and commissioning tests.

GE Multilin 369, GE 369 Relay, GE Motor Protection Relay, Motor Protection, Thermal Overload Protection, ANSI 49, Motor Starting Protection, Locked Rotor Protection, ANSI 46, Earth Fault Protection, EnerVista, Motor Protection Testing, Power System Protection

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top