- 1. Introduction
- 2. GE Multilin B30 and B90 Busbar Protection Relays
- 3. Why Busbar Differential Protection Is Required
- 4. Operating Principle of Busbar Differential Protection (ANSI 87B)
- 5. Differential and Restraint Currents
- 6. CT Requirements for Busbar Differential Protection
- 7. Busbar Protection Zones
- 8. Busbar Zone Selection and Disconnector Status
- 9. Check-Zone Concept
- 10. Busbar Protection Trip Logic
- 11. CT Supervision and Differential Stability
- 12. Practical Differential Current Example
- 13. GE Multilin B30 and B90 Engineering Workflow
- Step 1 – Review the Substation Single-Line Diagram
- Step 2 – Define the Differential Zones
- Step 3 – Verify CT Data
- Step 4 – Configure Current Inputs
- Step 5 – Configure Zone Selection
- Step 6 – Configure Differential Protection
- Step 7 – Configure Trip Logic
- Step 8 – Configure Alarms and Monitoring
- Step 9 – Save and Review
- 14. Testing GE Multilin Busbar Protection
- 15. Common Busbar Protection Problems
- 16. Practical Busbar Protection Commissioning Checklist
- 17. Engineering Recommendations
- 18. Conclusion
- 19. Training on GE Multilin Busbar Protection by Elec-Engg
1. Introduction
Busbars are critical components of electrical substations. They connect incoming feeders, outgoing feeders, transformers, generators, and other electrical circuits within a common switching arrangement.
A fault on a busbar can be particularly severe because several sources may feed the fault simultaneously. Unless the fault is cleared rapidly, it can cause extensive equipment damage, supply interruption, and loss of substation stability.
Busbar differential protection, identified by ANSI device number 87B, is widely used to detect internal busbar faults and isolate the affected bus section.
GE Multilin provides busbar protection solutions within its protection relay portfolio, including the B30 and B90 families. The exact application, available functions, hardware arrangements, and engineering options depend on the relay model, firmware, and configuration.
This article explains the practical principles of GE Multilin busbar protection, including differential measurement, CT selection, bus zone configuration, breaker and disconnector status, CT saturation, check-zone concepts, trip logic, testing, and commissioning.
2. GE Multilin B30 and B90 Busbar Protection Relays
2.1 GE Multilin B30
The GE Multilin B30 is associated with busbar protection applications.
Its suitability depends on the required busbar arrangement, number of circuits, CT inputs, available logic, and the protection scheme design.
Before selecting the B30, the engineer should verify:
- Number of required current inputs.
- Number of protected circuits.
- Busbar arrangement.
- Required differential zones.
- CT input specifications.
- Required binary inputs and outputs.
- Communication requirements.
- Firmware and ordering-code limitations.
2.2 GE Multilin B90
The GE Multilin B90 is a bus differential protection system intended for more complex busbar protection applications.
Depending on the system configuration, its engineering may involve multiple current measurements, bus zone selection, breaker and disconnector status, differential protection logic, and communication between system components.
The precise system architecture must be taken from the documentation for the selected B90 version.
2.3 Relay Selection
The selection of a busbar protection relay should consider:
- Busbar configuration.
- Number of bays.
- Number of CT circuits.
- Number of bus sections.
- Bus coupler and sectionalizer arrangements.
- Main and transfer bus arrangements.
- Required differential zones.
- CT characteristics.
- Required isolation and trip philosophy.
- Future substation expansion.
- Communication and redundancy requirements.
A simple busbar arrangement and a complex double-bus substation may require significantly different protection architectures.
3. Why Busbar Differential Protection Is Required
A busbar connects multiple electrical circuits. A fault on the busbar may receive contributions from several connected sources.
For example, consider a busbar connected to:
- Two incoming transformer feeders.
- Three outgoing distribution feeders.
- One bus coupler.
- One generator feeder.
If an internal busbar fault occurs, the fault current can flow from several connected circuits.
The busbar protection system must identify the affected zone and trip the circuit breakers required to isolate it.
The main objectives are:
- Detect internal busbar faults rapidly.
- Remain stable during external faults.
- Identify the correct busbar section.
- Trip only the circuit breakers necessary for isolation.
- Supervise CT circuits and switching arrangements.
- Avoid unnecessary tripping during normal switching operations.
4. Operating Principle of Busbar Differential Protection (ANSI 87B)
Busbar differential protection is based on Kirchhoff’s Current Law.
Under normal operating conditions, the vector sum of currents entering and leaving a protected busbar zone should be approximately zero.
For a simplified busbar with several connected circuits:
[
I_{\text{diff}}=\left|\sum_{k=1}^{n} I_k\right|
]
Where:
- (I_{\text{diff}}) is the differential current.
- (I_k) represents each measured circuit current referred to a common reference direction.
- (n) is the number of circuits connected to the protected zone.
The current directions must be defined consistently.
4.1 Normal Operating Condition
During normal operation, the current entering the busbar is approximately equal to the total current leaving it.
Therefore:
[
I_{\text{diff}}\approx0
]
Small differential current may exist due to CT errors, measurement tolerances, and other practical factors.
4.2 External Fault
An external fault occurs outside the protected busbar zone.
For example, a fault on an outgoing feeder should normally be cleared by the feeder protection.
The busbar differential protection must remain stable even when large through-fault currents flow through the CTs.
4.3 Internal Busbar Fault
An internal busbar fault occurs within the differential protection zone.
The currents entering the zone contribute to the fault rather than balancing the currents leaving the zone.
The resulting differential current can cause the relay to operate.
5. Differential and Restraint Currents
Numerical busbar protection systems commonly use differential and restraint quantities to distinguish internal faults from external faults and measurement errors.
A simplified differential quantity is:
[
I_{\text{diff}}=\left|\sum I_k\right|
]
A simplified restraint quantity may be based on the sum of the magnitudes of the connected currents:
[
I_{\text{rest}}=\sum |I_k|
]
The exact restraint definition depends on the relay algorithm.
5.1 Percentage Differential Characteristic
A simplified differential operating condition can be represented as:
[
I_{\text{diff}}>I_{\min}+S I_{\text{rest}}
]
Where:
- (I_{\min}) is the minimum differential pickup.
- (S) is a restraint slope.
- (I_{\text{rest}}) is the restraint quantity.
Actual B30 or B90 characteristics must be obtained from the applicable product documentation.
5.2 High-Impedance and Low-Impedance Differential Protection
Busbar differential protection can be implemented using different protection principles.
High-impedance differential protection uses a stabilizing impedance arrangement and requires carefully matched CT characteristics and suitable CT secondary circuits.
Low-impedance numerical differential protection calculates differential and restraint quantities using numerical measurements and protection algorithms.
The B30 and B90 application must be understood from the actual relay design rather than assuming that all busbar differential systems use the same operating principle.
6. CT Requirements for Busbar Differential Protection
Current transformer performance is one of the most important factors in busbar protection.
During an external fault, very high current may flow through the CTs of the connected circuits.
If one CT saturates significantly earlier than the others, the measured current balance can be disturbed.
This may produce unwanted differential current.
6.1 CT Ratio Selection
The CT ratios should be selected according to:
- Maximum circuit load current.
- Maximum fault current.
- Relay input rating.
- CT accuracy class.
- CT knee-point voltage, where relevant.
- Secondary burden.
- CT transient performance.
- Protection scheme requirements.
6.2 CT Polarity
All CTs connected to a differential protection scheme must have correct polarity and consistent current reference directions.
Incorrect CT polarity can create differential current during normal load conditions.
6.3 CT Saturation
CT saturation can occur during high-magnitude fault current, particularly when the current contains a significant DC component.
Potential consequences include:
- Distorted secondary current.
- Reduced measured current magnitude.
- Incorrect phase relationship.
- False differential current.
- Delayed or unwanted protection operation.
The busbar protection design must account for the expected fault level and CT performance.
6.4 CT Secondary Circuit Inspection
The commissioning engineer should verify:
- CT shorting links.
- Test terminal arrangements.
- Secondary earthing.
- Terminal tightness.
- Cable continuity.
- Correct phase identification.
- CT circuit insulation.
- Absence of unintended open circuits.
CT secondary circuits must never be opened while primary current is flowing.
7. Busbar Protection Zones
A modern substation may contain several busbar sections and multiple circuit breakers.
The protection system must determine which circuits belong to each differential zone.
Typical arrangements include:
- Single busbar.
- Single busbar with sectionalizer.
- Double busbar.
- Main and transfer bus.
- One-and-a-half breaker arrangement.
- Double breaker arrangement.
- Ring bus.
Each arrangement creates different requirements for zone selection and breaker tripping.
7.1 Single Busbar
A single busbar arrangement has one main busbar connected to all incoming and outgoing circuits.
The differential protection zone normally includes the CTs associated with all connected circuits.
7.2 Sectionalized Busbar
A sectionalized busbar consists of two or more sections connected through a bus sectionalizer or bus coupler.
Each section may have its own differential protection zone.
A fault on one section should not unnecessarily disconnect the healthy section if the switching and protection design allows selective isolation.
7.3 Double Busbar
A double-busbar substation allows circuits to be connected to either of two busbars through disconnectors.
The protection system must correctly identify the busbar to which each circuit is connected.
This requires reliable disconnector status information and suitable zone-selection logic.
7.4 Main and Transfer Bus
A main-and-transfer-bus arrangement allows selected circuits to be transferred to an alternative busbar for maintenance or operational flexibility.
The busbar protection scheme must account for the temporary switching arrangement.
8. Busbar Zone Selection and Disconnector Status
In complex substations, busbar zone selection depends on the actual position of disconnectors and circuit breakers.
The protection system may use auxiliary contacts to determine whether a circuit is connected to Bus 1, Bus 2, or another bus section.
8.1 Disconnector Position
A disconnector may provide separate auxiliary contacts for open and closed indication.
The relay or associated logic system uses these indications to determine the circuit’s busbar connection.
8.2 Status Supervision
The protection system should detect abnormal or contradictory status conditions.
Examples include:
- Both open and closed indications active.
- Both indications inactive.
- Unavailable auxiliary supply.
- Inconsistent switching sequence.
- Invalid combination of busbar connections.
The response to invalid status information must be defined in the protection design.
8.3 Switching Conditions
Busbar transfer and switching operations can change the differential zone membership.
The zone-selection logic must remain correct during approved switching sequences.
The commissioning engineer should test normal and abnormal switching combinations.
9. Check-Zone Concept
Some busbar protection designs use a check-zone principle.
A check zone is an additional differential supervision zone intended to provide an independent confirmation of a busbar fault.
Depending on the protection architecture, the check zone may cover a broader area than an individual selective bus zone.
The check-zone principle can help prevent incorrect operation caused by erroneous zone selection or switching status information.
However, check-zone availability and implementation are model- and scheme-dependent. The actual B30 or B90 design documentation must be consulted.
10. Busbar Protection Trip Logic
When an internal busbar fault is detected, the protection system must trip the circuit breakers connected to the affected zone.
For a double-busbar arrangement, the tripping logic must identify which circuits are connected to the faulted busbar.
The protection design may also include:
- Breaker failure protection.
- Bus coupler trip logic.
- Bus sectionalizer trip logic.
- Lockout relay operation.
- Transfer trip signals.
- Interlocking.
- Alarm and event recording.
10.1 Selective Tripping
Selective tripping is essential to avoid unnecessary substation outages.
A fault on Bus 1 should normally isolate Bus 1 while preserving healthy Bus 2 circuits where the system arrangement permits.
10.2 Breaker Failure Protection (ANSI 50BF)
If a circuit breaker fails to open after a busbar protection trip command, breaker failure protection may initiate additional isolation.
The breaker failure scheme should consider:
- Breaker current supervision.
- Breaker auxiliary contacts.
- Timer settings.
- Retrip logic.
- Upstream breaker tripping.
- Busbar protection coordination.
11. CT Supervision and Differential Stability
A busbar protection system must remain dependable when CT circuits or measurement channels become abnormal.
Possible CT circuit problems include:
- Open secondary wiring.
- Shorted CT secondary.
- Incorrect polarity.
- Loose terminals.
- Failed test links.
- Incorrect CT ratio.
- CT saturation.
Numerical relays may provide measurement supervision, CT circuit supervision, or other diagnostic functions, depending on the product.
The protection engineer should understand how the selected relay responds to each detected condition.
An alarm, blocking action, or other response should be defined according to the approved protection philosophy.
12. Practical Differential Current Example
Consider a simplified busbar with three connected circuits.
The measured currents, using a common reference direction, are:
- Incoming circuit: 800 A.
- Outgoing feeder 1: 500 A.
- Outgoing feeder 2: 300 A.
Under normal conditions:
[
I_{\text{diff}}=|800-500-300|
]
[
I_{\text{diff}}=0\text{ A}
]
Now consider an internal fault where the current entering the busbar is 800 A, while the outgoing currents total only 100 A.
The simplified differential current is:
[
I_{\text{diff}}=|800-100|
]
[
I_{\text{diff}}=700\text{ A}
]
The resulting differential current indicates a significant imbalance and may cause the differential element to operate if the configured operating conditions are satisfied.
This example is simplified. Actual numerical relay calculations use CT secondary measurements, configured scaling, current direction conventions, and the relay’s differential and restraint algorithms.
13. GE Multilin B30 and B90 Engineering Workflow
The exact configuration process depends on the relay model, firmware, and engineering software.
A general engineering workflow is described below.
Step 1 – Review the Substation Single-Line Diagram
Identify:
- Busbar sections.
- Incoming feeders.
- Outgoing feeders.
- Bus couplers.
- Sectionalizers.
- Circuit breakers.
- Disconnectors.
- CT locations.
- Protection zones.
Step 2 – Define the Differential Zones
Prepare a zone diagram showing which CTs belong to each busbar protection zone.
For double-busbar arrangements, define the zone-selection logic and switching conditions.
Step 3 – Verify CT Data
Collect:
- CT ratios.
- CT secondary ratings.
- Accuracy class.
- Protection characteristics.
- Knee-point data, where applicable.
- Secondary burden.
- Maximum fault current.
Step 4 – Configure Current Inputs
Enter the CT ratios and configure the required current measurement channels.
Verify phase assignment and current reference direction.
Step 5 – Configure Zone Selection
Where required, configure the disconnector and circuit-breaker status inputs.
Verify that the protection system identifies the correct busbar zone under each approved switching condition.
Step 6 – Configure Differential Protection
Review:
- Differential pickup.
- Restraint characteristic.
- Operating logic.
- Zone configuration.
- CT supervision.
- Trip output assignment.
Use the actual relay documentation for the available parameters and setting ranges.
Step 7 – Configure Trip Logic
Verify the circuit breakers that must trip for each busbar fault zone.
Check bus coupler and bus sectionalizer logic.
Step 8 – Configure Alarms and Monitoring
Configure the required alarm and status signals, where supported.
Typical indications may include:
- Differential protection operation.
- CT circuit supervision.
- Zone selection status.
- Disconnector status.
- Protection system alarm.
- Breaker failure initiation.
- Communication or hardware alarm.
Step 9 – Save and Review
Save the final settings and logic configuration.
Perform an independent review against the approved protection drawings and protection study.
14. Testing GE Multilin Busbar Protection
Busbar protection testing is more complex than testing a single feeder overcurrent relay because the test must verify differential stability, internal fault operation, zone selection, and trip logic.
14.1 CT Input Measurement Test
Inject known current values into the relevant current inputs.
Verify:
- Phase current magnitude.
- Phase assignment.
- CT ratio scaling.
- Current polarity.
- Measurement direction.
14.2 Differential Stability Test
Apply balanced through-current conditions to the connected circuit inputs.
Verify that the differential protection remains stable under normal and external-fault simulation conditions.
14.3 Differential Operating Test
Simulate an internal busbar fault by applying current inputs that produce differential current.
Verify:
- Differential pickup.
- Operating time.
- Correct protection zone.
- Correct trip output.
14.4 CT Saturation Stability Test
Where required by the project test specification, perform a suitable stability test representing external fault conditions and CT saturation effects.
The test method should be based on the relay manufacturer’s recommendations and the protection design.
14.5 Zone Selection Test
For double-busbar and more complex arrangements, test the different disconnector positions.
Verify that each circuit is assigned to the correct busbar protection zone.
14.6 Check-Zone Test
If the scheme includes a check zone, test its operating and supervision logic according to the approved design.
14.7 Breaker Failure Test
Simulate a breaker failure condition after a trip command.
Verify:
- Breaker failure initiation.
- Current supervision.
- Timer operation.
- Retrip output.
- Backup tripping logic.
14.8 Complete Trip Circuit Test
Verify the complete protection path:
Differential element → Protection logic → Trip output → Lockout relay → Circuit breaker trip coil
Test all required breakers for each busbar protection zone.
15. Common Busbar Protection Problems
Problem 1 – Differential Current Exists During Normal Operation
Possible causes:
- Incorrect CT polarity.
- Incorrect CT ratio.
- Incorrect phase assignment.
- Incorrect current direction reference.
- Wiring errors.
- CT secondary circuit problems.
Recommended action: Verify each CT circuit and compare measured currents under known load conditions.
Problem 2 – Busbar Protection Trips During an External Fault
Possible causes:
- CT saturation.
- Incorrect CT selection.
- Incorrect CT wiring.
- Inappropriate differential settings.
- Incorrect zone configuration.
- Defective or abnormal CT secondary circuit.
Recommended action: Review the disturbance records and investigate the CT performance during the fault.
Problem 3 – Wrong Busbar Zone Is Selected
Possible causes:
- Incorrect disconnector auxiliary contacts.
- Incorrect input mapping.
- Incorrect zone-selection logic.
- Inconsistent status signals.
- Incorrect switching sequence.
Recommended action: Test all approved disconnector combinations and compare relay status with the actual substation arrangement.
Problem 4 – Some Circuit Breakers Do Not Trip
Possible causes:
- Incorrect trip matrix.
- Missing output assignment.
- Defective output contact.
- Incorrect lockout wiring.
- Circuit breaker trip circuit failure.
- Missing auxiliary supply.
Recommended action: Test the complete trip circuit for each breaker associated with the affected zone.
Problem 5 – CT Supervision Alarm Appears
Possible causes:
- Open CT circuit.
- Incorrect test switch position.
- Wiring fault.
- Measurement inconsistency.
- Hardware or input problem.
Recommended action: Investigate the secondary circuit using approved CT safety procedures.
16. Practical Busbar Protection Commissioning Checklist
- Approved single-line diagram reviewed.
- Busbar protection zone diagram prepared.
- Relay model and firmware confirmed.
- CT ratios and secondary ratings verified.
- CT polarity checked.
- CT secondary circuits inspected.
- Current input measurements verified.
- Differential stability test completed.
- Differential operating test completed.
- External fault stability verified.
- CT saturation stability requirements reviewed.
- Busbar zone selection tested.
- Disconnector status inputs verified.
- Check-zone logic tested, where applicable.
- Bus coupler logic verified.
- Breaker failure protection tested.
- Trip matrix verified.
- All associated circuit breaker trip circuits tested.
- Alarm and indication signals verified.
- Event and disturbance records reviewed.
- Final settings and test reports archived.
17. Engineering Recommendations
For dependable busbar protection:
- Start with an accurate single-line diagram.
- Define every differential zone clearly.
- Select CTs based on fault level and protection requirements.
- Verify CT polarity and phase assignment.
- Consider CT saturation during external faults.
- Test all busbar switching and zone-selection conditions.
- Verify disconnector auxiliary contacts.
- Review check-zone logic where provided.
- Coordinate busbar tripping with breaker failure protection.
- Test the complete trip matrix.
- Review abnormal CT circuit conditions.
- Archive relay settings, logic diagrams, and commissioning records.
18. Conclusion
GE Multilin B30 and B90 busbar protection solutions are intended for busbar protection applications with different engineering requirements.
Reliable busbar differential protection depends on more than the differential pickup setting. Correct CT selection, current polarity, zone definition, disconnector status, switching logic, CT saturation performance, and trip circuit configuration are all essential.
The protection engineer must verify that internal busbar faults are detected quickly while external faults and normal switching conditions do not cause unwanted operation.
A complete commissioning program should include differential stability, internal fault operation, zone selection, breaker failure logic, CT supervision, and full trip circuit testing.
19. Training on GE Multilin Busbar Protection by Elec-Engg
Elec-Engg provides practical technical training by Dr Saeed Roostaee (Electrical Engineering) for engineers involved in power system protection, substation protection, relay configuration, testing, and commissioning.
Relevant training topics include:
- GE Multilin B30 and B90 busbar protection engineering.
- Busbar differential protection principles (ANSI 87B).
- Differential and restraint current calculations.
- CT selection, polarity, and saturation.
- Single and double busbar protection schemes.
- Busbar zone selection and disconnector status.
- Check-zone concepts.
- Breaker failure protection (ANSI 50BF).
- Trip matrix and protection logic.
- Relay configuration and settings management.
- Secondary injection and differential stability testing.
- Practical commissioning and troubleshooting.
Training is available through pre-recorded video courses, structured self-paced programs, live online sessions, face-to-face courses, and customized in-house training.
Visit https://elec-engg.com/ to explore available technical training programs or contact Elec-Engg through https://elec-engg.com/contact/ for customized training requirements.
