MiCOM P63x & P64x Transformer Protection Relays: Differential, REF, Settings & Testing

Table Of Contents
  1. 1. Introduction to MiCOM P63x and P64x Transformer Protection Relays
  2. 2. MiCOM P63x and P64x Relay Models
  3. 3. Transformer Differential Protection Operating Principle
  4. 4. Transformer Differential Protection Characteristics
  5. 5. Transformer Vector Group Compensation
  6. 6. CT Ratio Matching and Current Scaling
  7. 7. Transformer Tap Changer Effects
  8. 8. Magnetizing Inrush and Inrush Restraint
  9. 9. Overexcitation Protection – V/Hz Protection
  10. 10. Restricted Earth Fault Protection (REF)
  11. 11. Phase and Earth-Fault Overcurrent Protection
  12. 12. Thermal Overload Protection
  13. 13. Transformer Differential Protection Settings
  14. 14. Transformer Differential Protection Configuration Software
  15. 15. MiCOM P63x and P64x Relay Testing and Commissioning
  16. 16. Common MiCOM Transformer Protection Problems
  17. 17. Transformer Differential Protection vs REF Protection
  18. 18. Important Transformer Protection Engineering Documents
  19. 19. MiCOM Transformer Protection Training by Elec-Engg
  20. 20. Conclusion

1. Introduction to MiCOM P63x and P64x Transformer Protection Relays

Power transformers are among the most important and expensive components in electrical power systems. A transformer fault can cause serious equipment damage, supply interruption and safety risks. Reliable transformer protection is therefore essential in substations, power plants and industrial electrical networks.

The MiCOM P63x and P64x families are numerical transformer protection relay families designed for transformer differential protection and associated protection functions. Their application depends on the relay model, hardware configuration, firmware and available options.

Transformer differential protection compares the currents entering and leaving the protected transformer zone. The relay compensates for transformer ratio and vector-group effects before evaluating the differential current.

Depending on the specific model, these relay families may provide functions such as:

  • Transformer differential protection.
  • Percentage biased differential characteristics.
  • Restricted earth fault (REF) protection.
  • Magnetizing inrush detection and restraint.
  • Overexcitation protection.
  • Phase and earth-fault overcurrent protection.
  • Thermal overload protection.
  • Breaker failure protection.
  • Disturbance and event recording.
  • Transformer backup protection functions.
  • Communication and substation automation interfaces.

The exact functions must be confirmed using the technical documentation for the individual relay.

2. MiCOM P63x and P64x Relay Models

The transformer protection portfolio includes different relay variants designed for different transformer configurations and protection requirements.

Relay familyModels coveredGeneral application
P63xP631, P632, P633, P634Transformer differential protection variants
P64xP641, P642, P643, P645Transformer protection variants

The models may differ in:

  • Number of transformer windings supported.
  • Differential protection configuration.
  • REF protection availability.
  • Current input arrangements.
  • Backup protection functions.
  • Hardware and communication options.
  • Setting software and firmware compatibility.

Do not assume that all models have identical functions or support the same transformer configurations.

Before preparing settings, identify the full model designation, order code, firmware version, transformer application and installed options.

3. Transformer Differential Protection Operating Principle

Transformer differential protection is based on comparing the currents entering and leaving the transformer.

For an ideal transformer operating under normal conditions, the ampere-turn balance means that the currents on the different sides are related by the transformer turns ratio.

However, the currents measured by the relay are affected by:

  • Transformer ratio.
  • Vector group.
  • CT ratios.
  • Phase displacement.
  • Transformer tap position.
  • Zero-sequence current behavior.
  • Magnetizing current.

The relay must compensate for these factors before calculating the differential current.

A simplified differential current expression is:

\[ I_{\text{diff}}=\left|I_1+I_2\right| \]

Here, currents are referred to a common reference and their directions are defined relative to the protected transformer zone.

For a transformer with more than two windings, the relay evaluates the appropriately compensated current contributions from the relevant sides.

Frontiers | Transformer Monitoring and Protection in Dynamic Power Systems – A Review

frontiersin.org

Under normal operating conditions, the compensated currents should approximately balance. For an internal transformer fault, the difference increases and the relay may initiate tripping.

4. Transformer Differential Protection Characteristics

Transformer differential relays generally use biased or percentage differential protection to achieve sensitivity while maintaining stability during external faults.

4.1 Differential current

Differential current represents the imbalance between the compensated transformer-side currents.

It increases during internal faults and can also be affected by CT errors, tap changes and other operating conditions.

4.2 Restraint current

The restraint quantity helps the relay remain stable during external faults and high through-current conditions.

Its calculation depends on the relay design.

4.3 Percentage biased differential characteristic

A typical differential characteristic includes:

  • Minimum differential pickup.
  • One or more percentage restraint slopes.
  • Breakpoints between characteristic regions.
  • High-set differential protection, where provided.

The percentage bias helps prevent unwanted operation when current measurement errors become more significant at high through-fault currents.

4.4 High-set differential protection

A high-set differential element may provide fast operation for severe internal faults.

Its setting must be selected with consideration of transformer inrush, CT performance and the relay’s operating characteristics.

5. Transformer Vector Group Compensation

One of the most important engineering tasks in transformer differential protection is vector group compensation.

Transformers can introduce phase displacement between primary and secondary currents.

For example, a transformer with a delta-star vector group produces a phase displacement between the currents on its two sides.

If this phase displacement is not correctly compensated, the relay may calculate an unwanted differential current during normal transformer operation.

The engineer must configure the correct transformer vector group and corresponding compensation settings.

Important information includes:

  • Transformer vector group.
  • Rated primary voltage.
  • Rated secondary voltage.
  • Rated transformer power.
  • Winding arrangement.
  • CT ratios.
  • Relay current input configuration.

The relay’s internal compensation method should be followed. Do not apply additional external compensation unless it is required by the manufacturer’s design.

6. CT Ratio Matching and Current Scaling

Transformer protection often uses CTs with different ratios on the transformer sides.

The relay must scale the measured currents to a common reference.

For example, consider a transformer with:

  • Rated power: 40 MVA.
  • HV voltage: 132 kV.
  • LV voltage: 33 kV.

The rated line currents can be calculated using:

\[ I=\frac{S}{\sqrt{3}V} \]

For the HV side:

\[ I_{HV}=\frac{40\times10^6}{\sqrt{3}\times132\times10^3} \]

\[ I_{HV}\approx175\text{ A} \]

For the LV side:

\[ I_{LV}=\frac{40\times10^6}{\sqrt{3}\times33\times10^3} \]

\[ I_{LV}\approx700\text{ A} \]

The actual CT ratios should be selected according to the protection design and CT performance requirements.

The relay configuration must correctly account for CT ratios and current scaling.

Incorrect CT ratios can cause differential current during normal load conditions and may lead to unwanted operation.

7. Transformer Tap Changer Effects

On-load tap changers (OLTCs) change the transformer voltage ratio to regulate the system voltage.

A change in transformer ratio affects the currents measured on the transformer sides.

The differential relay must remain stable within the expected tap range.

Engineering considerations include:

  • Maximum and minimum tap positions.
  • Transformer rated ratio.
  • Tap range.
  • CT ratio selection.
  • Differential restraint characteristic.
  • Current measurement accuracy.

The differential settings should account for the maximum expected ratio mismatch without compromising sensitivity to internal faults.

8. Magnetizing Inrush and Inrush Restraint

Transformer energization can produce a high magnetizing inrush current.

This current can be significantly higher than the normal magnetizing current and may cause a false differential current.

Because inrush current enters the transformer without an equivalent current leaving the other winding, the differential relay must distinguish it from an internal fault.

Depending on the relay design, inrush restraint may use harmonic content or other waveform-based detection methods.

8.1 Second harmonic restraint

Magnetizing inrush current often contains a significant second-harmonic component.

A simplified second-harmonic ratio is:

\[ H_2=\frac{I_2}{I_1}\times100\% \]

Where:

  • \(I_2\) is the second-harmonic component.
  • \(I_1\) is the fundamental-frequency component.

The relay may use a configured criterion to identify inrush conditions and restrain differential tripping.

8.2 Inrush restraint settings

Important considerations include:

  • Harmonic restraint threshold.
  • Differential pickup.
  • Transformer energization conditions.
  • Residual flux.
  • Switching angle.
  • Transformer design.
  • System voltage conditions.

The exact inrush detection and restraint logic differs between relay models.

8.3 Transformer energization testing

The commissioning procedure should verify the correct configuration and operation of the inrush restraint function according to the manufacturer’s recommended test method.

A secondary injection test may verify the relevant logic, but it does not necessarily reproduce every aspect of actual transformer energization.

9. Overexcitation Protection – V/Hz Protection

Transformer overexcitation can occur when the voltage-to-frequency ratio exceeds the transformer’s design limits.

The magnetic flux in a transformer is approximately proportional to:

\[ \Phi\propto\frac{V}{f} \]

Where:

  • \(V\) is the applied voltage.
  • \(f\) is the supply frequency.
  • \(\Phi\) is the magnetic flux.

Overexcitation can cause core saturation, increased magnetizing current, overheating and damage to transformer insulation.

A V/Hz protection function, where provided, can detect excessive excitation.

Important engineering considerations include:

  • Rated voltage.
  • Rated frequency.
  • Transformer excitation limits.
  • Time-current characteristic.
  • Alarm and trip thresholds.
  • Coordination with generator and network protection.

The availability and implementation of this function must be checked for the particular relay.

10. Restricted Earth Fault Protection (REF)

Restricted earth fault protection is a sensitive protection method used to detect earth faults within a defined transformer winding zone.

It is commonly applied to suitably grounded transformer windings.

REF protection compares the residual current from the phase CTs with the current measured by the neutral CT.

For a simplified arrangement:

\[ I_{\text{res}}=I_A+I_B+I_C \]

The relay compares the residual phase current with the neutral current, taking account of the configured current directions and protection arrangement.

10.1 REF protection applications

REF protection can provide sensitive detection of earth faults within the protected winding zone.

Applications include:

  • Star-connected transformer windings with an accessible neutral.
  • Solidly grounded transformer windings.
  • Resistance-grounded transformer windings, where the protection design is suitable.

10.2 High-impedance and low-impedance REF

Two common REF protection approaches are:

High-impedance REF: Uses a high-impedance differential arrangement with suitable CT requirements and stabilizing components.

Low-impedance REF: Uses numerical relay measurement and restraint or directional logic, depending on the relay design.

The specific P63x or P64x relay must be checked to establish which REF arrangement and functions are supported.

10.3 REF settings

Important parameters may include:

  • Pickup current.
  • Stabilizing or restraint settings.
  • Neutral CT ratio.
  • Phase CT ratios.
  • Directional supervision, where applicable.
  • Trip delay.
  • Alarm and trip logic.

REF protection requires particular care with CT polarity, CT matching and wiring.

11. Phase and Earth-Fault Overcurrent Protection

Transformer differential protection is often supported by overcurrent protection.

Depending on the model, the relay may provide phase and earth-fault overcurrent elements for backup protection.

Typical functions include:

  • Phase overcurrent.
  • Earth-fault overcurrent.
  • Directional overcurrent, where available.
  • Definite-time protection.
  • Inverse-time protection, where supported.

The settings must be coordinated with downstream feeder protection, upstream network protection and transformer thermal limits.

12. Thermal Overload Protection

Transformer overload protection helps prevent excessive temperature rise caused by sustained overloading.

The available thermal protection functions depend on the relay model and configuration.

Engineering should consider:

  • Transformer rated current.
  • Cooling arrangement.
  • Ambient temperature.
  • Transformer thermal characteristics.
  • Permitted overload duration.
  • Manufacturer loading guide.

Transformer thermal monitoring may also be provided through separate temperature monitoring equipment and should be coordinated with the electrical protection system.

13. Transformer Differential Protection Settings

Correct settings are essential for dependable transformer protection.

Typical setting groups include:

Setting groupImportant parameters
Transformer dataRated power and voltage
Vector groupWinding connection and phase displacement
CT configurationCT ratios and current input settings
Differential protectionMinimum pickup and operating characteristic
RestraintBias slopes and characteristic breakpoints
High-set differentialHigh-set operating threshold, where available
Inrush restraintHarmonic or other inrush detection settings
REF protectionPickup, CT ratios and protection logic
OverexcitationV/Hz alarm and trip settings, where available
OvercurrentPickup and time-current characteristics
Trip logicTrip outputs and protection matrix
CommunicationCommunication parameters and supervision

Actual parameter names and setting ranges vary by model and firmware.

14. Transformer Differential Protection Configuration Software

Configuration software depends on the MiCOM relay generation and firmware.

For supported devices, engineering may be performed using MiCOM S1 Studio, Easergy Studio or another compatible tool specified by the manufacturer.

Typical engineering activities include:

  1. Identify the relay model and firmware.
  2. Create or open the correct setting file.
  3. Enter transformer rated power and voltage.
  4. Configure winding connections and vector group.
  5. Configure CT ratios and input assignments.
  6. Enter differential protection settings.
  7. Configure inrush restraint.
  8. Configure REF protection, if available.
  9. Configure backup protection.
  10. Assign binary inputs and outputs.
  11. Configure alarms and trip logic.
  12. Review and validate the settings.
  13. Download the settings to the relay.
  14. Compare the relay settings with the approved configuration.

A settings comparison should be completed after downloading to verify that the relay contains the approved settings.

15. MiCOM P63x and P64x Relay Testing and Commissioning

Transformer protection testing should cover the differential protection function, REF protection where installed, backup protection and all associated trip and alarm circuits.

Omicron CMC test equipment with Test Universe, or another suitable secondary injection test system, can be used.

15.1 Initial inspection

Before testing, verify:

  • Relay model and hardware.
  • Firmware version.
  • Auxiliary supply.
  • CT wiring and polarity.
  • Current input configuration.
  • Binary inputs and outputs.
  • Approved relay settings.
  • Trip circuit connections.
  • Transformer protection drawings.

15.2 CT ratio and polarity checks

Check the CT ratios and polarity on all transformer sides.

Incorrect polarity can result in differential current under normal operating conditions.

Verify the current directions against the relay’s configured reference directions.

15.3 Differential current measurement

Inject balanced current conditions according to the relay’s test procedure.

Verify that the relay measures the expected current quantities and calculates the correct differential and restraint values.

15.4 Differential pickup test

Test the minimum differential pickup against the approved settings.

Record the actual pickup and dropout values where required by the commissioning procedure.

15.5 Differential bias characteristic test

Test the differential operating characteristic at different restraint current levels.

Verify:

  • Minimum differential pickup.
  • First slope.
  • Second slope, where provided.
  • Characteristic breakpoints.
  • High-set differential element, where provided.

15.6 Inrush restraint test

Verify the inrush restraint logic using the manufacturer’s recommended test method.

Where suitable, use a test waveform containing the relevant harmonic components.

Check:

  • Inrush detection.
  • Restraint behavior.
  • Differential trip security.
  • Event and alarm indications.

15.7 REF protection test

For relays with REF protection, verify:

  • Correct phase residual current measurement.
  • Neutral current measurement.
  • CT polarity.
  • REF pickup.
  • Directional or restraint logic, where applicable.
  • Trip output.
  • Operating time.

15.8 Overcurrent protection test

Test the configured phase and earth-fault overcurrent functions.

Check:

  • Pickup.
  • Dropout.
  • Operating time.
  • Definite-time or inverse-time characteristic.
  • Trip output.
  • Alarm indication.

15.9 Binary input and output testing

Verify the interface between the relay and transformer protection circuits.

Typical signals include:

  • Transformer differential trip.
  • REF trip.
  • Overcurrent trip.
  • Buchholz alarm and trip.
  • Pressure relief device.
  • Oil temperature alarm.
  • Winding temperature alarm.
  • Circuit breaker status.
  • External blocking.
  • Breaker failure initiation.

Not every signal is directly provided by the relay. Some are connected through external transformer protection and monitoring devices.

15.10 Trip circuit testing

Verify the complete trip path from relay output contacts to the relevant circuit breaker trip coils.

Where the protection scheme requires it, test all transformer-side circuit breakers and associated trip logic.

16. Common MiCOM Transformer Protection Problems

ProblemPossible causeRecommended checks
Differential current during normal loadIncorrect CT ratio or polarityCheck CT wiring, ratio and settings
Differential trip during transformer energizationIncorrect inrush restraint configurationReview inrush settings and event records
Differential instability during external faultCT saturation or incorrect bias settingsReview CT performance and restraint characteristic
Incorrect phase differential measurementIncorrect vector group compensationVerify transformer vector group and relay configuration
REF unwanted operationIncorrect neutral CT polarity or wiringCheck neutral and phase CT circuits
REF does not operateIncorrect residual current or neutral current configurationCheck CT wiring, settings and REF logic
Overexcitation alarmExcessive V/Hz condition or incorrect settingsCheck voltage, frequency and V/Hz settings
Overcurrent unwanted operationIncorrect pickup or coordinationReview protection coordination study
Incorrect trip outputLogic or binary output assignment issueCheck protection matrix and output wiring

When investigating a transformer protection operation, compare the relay event records with transformer alarms, circuit breaker records and disturbance waveforms.

17. Transformer Differential Protection vs REF Protection

Transformer differential and REF protection are complementary functions, but they protect different zones and use different measurement arrangements.

FeatureTransformer differentialREF protection
Main purposeDetect internal transformer faultsDetect earth faults within a defined winding zone
MeasurementCurrent comparison between transformer sidesComparison of phase residual and neutral current
Fault coveragePhase and earth faults, depending on the schemeEarth faults within the protected zone
SensitivityDepends on differential settings and CT performanceCan provide sensitive earth-fault detection
CT arrangementCTs on relevant transformer sidesPhase CTs and neutral CT
Typical applicationMain transformer protectionAdditional winding earth-fault protection

Using both functions can improve transformer fault coverage where the transformer configuration and relay support permit.

18. Important Transformer Protection Engineering Documents

Before commissioning a transformer protection relay, engineers should review:

  • Transformer nameplate data.
  • Transformer vector group.
  • Transformer impedance data.
  • Transformer tap changer range.
  • CT data sheets.
  • CT ratio and polarity test reports.
  • Transformer differential protection study.
  • REF protection drawings.
  • Transformer protection and control schematics.
  • Circuit breaker trip diagrams.
  • Approved relay setting calculations.
  • Relay configuration files.
  • Commissioning and test procedures.

A correct transformer protection design requires coordination between electrical calculations, CT selection, relay settings and the actual wiring arrangement.

19. MiCOM Transformer Protection Training by Elec-Engg

Elec-Engg provides practical power system protection training for engineers working in utilities, substations, power plants and industrial facilities.

Training can be delivered in several formats:

Online Training: Live technical sessions covering transformer protection principles, differential protection, REF and relay settings.

Structured Self-Paced Training: Organized technical lessons, practical exercises and assessment materials that engineers can complete at their own pace.

Face-to-Face Training: Practical classroom training for engineers and commissioning teams.

Customized In-House Training: Training programs designed around the company’s transformer types, installed relay models, protection philosophy and project requirements.

Possible training topics include:

  • Transformer protection fundamentals.
  • Transformer differential protection.
  • Vector group compensation.
  • CT ratio calculations.
  • Differential pickup and bias settings.
  • Magnetizing inrush and harmonic restraint.
  • Restricted earth fault protection.
  • Overexcitation protection.
  • Transformer backup protection.
  • Omicron CMC and Test Universe.
  • Differential relay testing and commissioning.
  • Transformer fault analysis.

For information about available courses and customized training programs, contact Elec-Engg.

20. Conclusion

MiCOM P63x and P64x transformer protection relays are part of the MiCOM numerical protection portfolio for transformer protection applications.

Reliable operation requires correct transformer data, vector group compensation, CT ratio configuration, differential characteristic settings and appropriate inrush restraint.

REF and backup protection functions can provide additional fault coverage where supported by the relay and required by the protection design.

During commissioning, engineers should verify differential pickup, bias characteristics, inrush restraint, REF protection, backup elements and the complete trip circuit.

Always use the technical manual and setting guidance applicable to the exact relay model, firmware and installed options.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top