Sepam Generator Protection

Table Of Contents
  1. 1. Sepam Generator Protection Overview
  2. 2. Generator Differential Protection (87G)
  3. 3. Stator Earth Fault Protection (64G)
  4. 4. Rotor Earth Fault Protection (64R)
  5. 5. Loss of Excitation Protection (40)
  6. 6. Reverse Power Protection (32)
  7. 7. Negative Sequence Protection (46)
  8. 8. Overvoltage and Overfrequency Protection
  9. 9. Generator Backup Protection
  10. 10. Generator Protection Settings and Testing
  11. Practical Engineering Considerations for Sepam Generator Protection
  12. Conclusion

1. Sepam Generator Protection Overview

Generator protection systems are designed to detect abnormal electrical, thermal, and mechanical conditions that can threaten the generator, prime mover, excitation system, or power system.

Sepam protection relays can be applied in generator protection schemes depending on the selected relay model, hardware configuration, firmware version, available protection functions, and project requirements.

Generator protection is generally divided into several categories:

  • Internal fault protection
  • Stator winding protection
  • Rotor and excitation circuit protection
  • Abnormal operating condition protection
  • Backup protection
  • Thermal protection
  • System stability protection

Typical generator protection functions include:

ANSIProtection function
87GGenerator differential protection
64GStator earth fault protection
64RRotor earth fault protection
40Loss of excitation
32Reverse power
46Negative sequence protection
27Undervoltage
59Overvoltage
81UUnderfrequency
81OOverfrequency
50/51Instantaneous/time overcurrent
50N/51NEarth fault protection
49Thermal overload protection
24Overfluxing (V/Hz)
21Impedance protection, where applicable
78Out-of-step protection, where applicable

Not every Sepam model supports every function. Protection function availability must be verified against the relay model, application, hardware, and documentation.

Generator Protection Zones

A typical generator protection scheme may include the following protection zones:

  • Generator stator winding
  • Generator terminal connections
  • Generator neutral and grounding equipment
  • Generator circuit breaker
  • Generator transformer, if included in the unit protection scheme
  • Rotor field winding and excitation system
  • Generator auxiliary circuits

Protection zones should be designed with adequate overlap to minimize unprotected areas.

2. Generator Differential Protection (87G)

Generator differential protection is one of the primary protections used to detect faults inside the generator stator winding.

It compares the currents entering and leaving a protected zone. Under normal operation and external fault conditions, the currents should balance according to the CT ratios and connections. During an internal fault, the differential current increases and the relay can operate.

Operating Principle

The differential protection system uses current transformers installed at the boundaries of the protected zone.

The relay compares the measured currents and calculates the differential current.

For a simplified two-end differential scheme:

\[ I_{\text{diff}}=|I_1+I_2| \]

The actual calculation depends on CT polarity, phase compensation, and relay implementation.

The relay also evaluates restraint or stabilizing current to avoid unwanted operation during:

  • External faults
  • CT saturation
  • CT ratio errors
  • Transient conditions
  • Measurement inaccuracies

Faults Detected

Generator differential protection can detect:

  • Phase-to-phase faults within the stator winding
  • Three-phase internal faults
  • Phase-to-earth faults within the protected zone, depending on grounding and sensitivity
  • Faults involving generator terminals and associated conductors inside the CT boundaries

Differential Protection Stability

Differential protection must remain stable during faults outside the protected zone.

For example, during an external fault, large currents may flow through the generator circuit. CT saturation or unequal CT performance can produce differential current even though the fault is external.

The relay therefore uses a differential characteristic with operating and restraint regions.

Typical engineering considerations include:

  • CT ratio selection
  • CT polarity verification
  • CT class and burden
  • CT saturation performance
  • Differential pickup
  • Restraint slope
  • High-set differential element
  • Trip logic
  • Breaker failure coordination

Typical Operation

When an internal fault is detected:

  1. The differential element detects abnormal differential current.
  2. The relay evaluates the operating and restraint quantities.
  3. Trip logic determines whether the fault condition satisfies the operating criteria.
  4. The generator circuit breaker is tripped.
  5. The excitation system may be de-excited through the associated trip scheme.
  6. Alarm, event, and disturbance records are generated.

Generator differential protection is normally considered a high-priority protection function because internal stator faults can cause severe damage.

3. Stator Earth Fault Protection (64G)

Stator earth fault protection detects insulation failure between the generator stator winding and earth.

The protection method depends on the generator neutral grounding arrangement and the amount of ground fault current available.

Common Generator Grounding Methods

Generators may use:

  • Solid grounding
  • Resistance grounding
  • Reactance grounding
  • Distribution transformer grounding
  • High-resistance grounding
  • Ungrounded systems

The grounding method determines the magnitude of earth fault current and influences the required protection sensitivity.

Earth Fault Detection Methods

Common stator earth fault protection methods include:

Neutral overvoltage protection

Voltage is measured at the generator neutral or grounding circuit.

An earth fault may produce a neutral displacement voltage, allowing the relay to detect insulation failure.

Neutral current protection

A CT installed in the neutral grounding circuit measures earth fault current.

The relay detects current above the configured threshold.

Residual current protection

Residual current is calculated or measured from the phase current inputs. This approach depends on the CT arrangement and the grounding system.

Third-harmonic-based protection

Some generator stator earth fault schemes use third-harmonic voltage components to improve coverage near the generator neutral.

The applicable protection method depends on generator design and relay capabilities.

Stator Earth Fault Protection Limitations

A conventional earth fault protection scheme may not protect the entire stator winding.

Faults close to the generator neutral can produce a low voltage or current quantity, making them difficult to detect using conventional protection alone.

A combination of protection methods may be necessary to achieve wider winding coverage.

Protection Settings Considerations

The setting process should consider:

  • Generator neutral grounding impedance
  • Maximum and minimum earth fault current
  • Neutral voltage measurement
  • CT/VT accuracy
  • Generator capacitance to earth
  • System grounding characteristics
  • Protection sensitivity
  • Time delay
  • Coordination with downstream and upstream protection

The objective is to detect insulation faults without unwanted operation during normal conditions or transient events.

4. Rotor Earth Fault Protection (64R)

The rotor field winding of a synchronous generator operates within an excitation circuit that is normally isolated from earth.

A single rotor earth fault may not produce a large fault current because the field circuit is not normally grounded. However, the first earth fault is an abnormal condition that requires detection.

If a second earth fault occurs at another location in the rotor circuit, it can create a short circuit path, potentially causing:

  • Rotor winding damage
  • Uneven magnetic flux
  • Rotor heating
  • Mechanical vibration
  • Magnetic imbalance
  • Severe generator damage

Operating Principle

Rotor earth fault protection monitors insulation between the field circuit and earth.

Depending on the protection system, detection may use:

  • Injection-based insulation monitoring
  • Voltage measurement
  • Field circuit insulation monitoring
  • Specialized rotor ground detection equipment

First Earth Fault

The first rotor earth fault is normally detected and alarmed.

The operating response depends on:

  • Generator manufacturer requirements
  • Power plant operating philosophy
  • Protection design
  • Rotor grounding detection system
  • Risk assessment

Some schemes provide an alarm for the first fault, requiring investigation and planned shutdown. Others may initiate a trip depending on the generator design and operating requirements.

Engineering Considerations

Rotor earth fault protection must consider:

  • Field circuit voltage
  • Excitation system arrangement
  • Brushless or static excitation
  • Insulation monitoring method
  • Detector sensitivity
  • Detection reliability
  • Alarm and trip philosophy

Rotor earth fault protection is particularly important for generators operating continuously at high loading.

5. Loss of Excitation Protection (40)

Loss of excitation protection detects abnormal conditions where the generator excitation system fails to maintain the required field current.

Excitation failure may occur due to:

  • Excitation system failure
  • AVR malfunction
  • Field circuit interruption
  • Loss of DC supply
  • Field breaker opening
  • Excitation control problems
  • Failure of excitation components

Generator Behavior During Loss of Excitation

When excitation is lost, the generator may lose its ability to maintain normal reactive power output.

Depending on the system conditions, the generator may begin absorbing reactive power from the network and operate as an induction generator.

Potential consequences include:

  • Reactive power absorption
  • Reduced terminal voltage
  • Rotor heating
  • Stator heating
  • Loss of synchronism
  • System voltage instability
  • Damage to excitation components

Loss of Excitation Protection Principle

Loss of excitation protection commonly uses impedance-based characteristics.

The relay measures generator terminal voltage and current and calculates the apparent impedance.

During loss of excitation, the impedance trajectory may enter the protection operating characteristic.

Depending on the protection design, the function may include multiple zones and time delays.

Setting Considerations

Settings must consider:

  • Generator capability curve
  • Generator reactances
  • Excitation limits
  • Minimum excitation operating conditions
  • System stability
  • Power system configuration
  • Impedance measurement characteristics
  • Time delays
  • Coordination with the AVR and excitation protection

Trip Logic

Loss of excitation may initiate:

  • Alarm
  • Generator breaker trip
  • Field breaker trip
  • Excitation shutdown
  • Turbine or prime mover shutdown, depending on the plant logic

The trip philosophy must be coordinated with the generator manufacturer and system stability studies.

6. Reverse Power Protection (32)

Reverse power protection prevents a generator from operating as a motor when the prime mover fails to supply mechanical power.

Under normal operation, the prime mover supplies mechanical energy to the generator, which converts it into electrical power.

When the mechanical input decreases significantly, the generator may begin importing active power from the network.

This condition is known as reverse power or motoring.

Causes of Reverse Power

Typical causes include:

  • Turbine trip
  • Loss of fuel supply
  • Loss of steam supply
  • Engine shutdown
  • Prime mover failure
  • Mechanical input reduction
  • Incorrect control operation

Operating Principle

Reverse power protection measures active power using voltage and current inputs.

The relay identifies the direction of active power flow.

When reverse power exceeds the configured threshold for the specified time, the protection operates.

The operating threshold and time delay must be appropriate for the prime mover.

Why Reverse Power Protection Is Important

Motoring can cause problems such as:

  • Turbine damage
  • Mechanical stress
  • Windage losses
  • Fuel system problems
  • Unwanted operation of the generator
  • Unnecessary energy consumption from the grid

The risks depend on the prime mover type.

Steam turbines, gas turbines, hydro turbines, and diesel engines have different motoring characteristics and protection requirements.

Settings Considerations

Reverse power settings should consider:

  • Minimum generator operating power
  • Prime mover motoring characteristics
  • Generator active power measurement accuracy
  • Power direction definition
  • CT and VT polarity
  • Power system configuration
  • Operating delays
  • Breaker trip logic

Correct polarity and phase association of voltage and current inputs are especially important for directional power protection.

7. Negative Sequence Protection (46)

Negative sequence protection detects unbalanced currents that can produce excessive heating in the generator rotor.

Unbalanced conditions create negative sequence current, which generates a magnetic field rotating opposite to the rotor direction.

This produces currents in the rotor structure and can lead to significant heating.

Causes of Negative Sequence Current

Typical causes include:

  • Unbalanced loads
  • Asymmetrical system faults
  • Open phase conditions
  • Unequal phase currents
  • Unbalanced switching
  • External system disturbances

Operating Principle

The relay calculates the negative sequence current component from the three phase currents.

Using symmetrical components, the negative sequence current is represented by:

\[ I_2=\frac{1}{3}(I_A+a^2I_B+aI_C) \]

where:

\[ a=1\angle120^\circ \]

The relay compares the calculated negative sequence current with configured protection thresholds.

Generator Heating

Negative sequence current produces rotor heating because of induced currents in the rotor body and related conductive components.

Generators have defined negative sequence current withstand capabilities.

The thermal limit is commonly represented by an I₂²t characteristic.

\[ I_2^2t=K \]

Where:

  • \(I_2\) is the negative sequence current
  • \(t\) is the operating time
  • \(K\) is the generator negative sequence withstand constant

The actual characteristic and allowable constant must be taken from the generator manufacturer.

Protection Objectives

Negative sequence protection is designed to:

  • Detect unbalanced operating conditions
  • Protect the rotor against excessive heating
  • Provide alarm for abnormal unbalance
  • Trip when the thermal withstand limit is exceeded

Settings Considerations

The settings should be based on:

  • Generator rated current
  • Generator negative sequence withstand capability
  • Thermal characteristic
  • Maximum system unbalance
  • CT accuracy
  • Protection coordination
  • Alarm threshold
  • Reset characteristic

8. Overvoltage and Overfrequency Protection

Generator overvoltage and overfrequency protection supervise conditions outside the generator’s normal operating range.

These functions are important during load rejection, system disturbances, regulator malfunction, and abnormal grid operation.

Overvoltage Protection (59)

Overvoltage protection detects excessive generator terminal voltage.

Causes

  • AVR malfunction
  • Load rejection
  • Incorrect excitation control
  • Voltage regulator failure
  • System voltage rise
  • Abnormal switching
  • Transformer or network conditions

Risks

Excessive voltage can stress:

  • Stator insulation
  • Generator winding insulation
  • Connected transformers
  • Auxiliary equipment
  • Voltage transformers
  • Power electronics and control systems

Settings Considerations

  • Generator rated voltage
  • Maximum continuous voltage capability
  • AVR operating limits
  • Transient voltage response
  • Generator capability curve
  • Protection coordination
  • Voltage measurement accuracy
  • Time delays

Depending on the application, protection may include multiple voltage stages with different operating delays.

Overfrequency Protection (81O)

Overfrequency protection detects frequency above the configured limit.

Overfrequency can occur when mechanical input exceeds electrical load, particularly during load rejection or governor control problems.

Causes

  • Load rejection
  • Governor malfunction
  • Turbine control failure
  • System islanding
  • Abnormal power system frequency

Risks

Excessive frequency may affect:

  • Turbine mechanical components
  • Generator rotor
  • Connected equipment
  • System stability
  • Generator operating limits

Underfrequency Protection (81U)

Underfrequency protection detects frequency below the configured operating limit.

Underfrequency may occur during:

  • Power system generation deficit
  • System disturbances
  • Islanding
  • Loss of generation
  • Excessive load
  • Frequency control problems

Protection settings must be coordinated with the generator’s operating capability, turbine limits, and system load-shedding schemes.

9. Generator Backup Protection

Backup protection is designed to detect faults or abnormal conditions when primary protection fails to operate or when a fault is not covered by the primary protection scheme.

Backup protection should be coordinated with generator, transformer, busbar, and network protection.

Overcurrent Protection (50/51)

Overcurrent protection detects currents exceeding configured thresholds.

It may be used for backup protection against:

  • External phase faults
  • Generator terminal faults
  • System faults
  • Certain abnormal operating conditions

Generator overcurrent protection must be coordinated with generator thermal limits and the system’s fault current contribution.

Earth Fault Backup (50N/51N)

Earth fault backup protection detects residual or neutral current associated with ground faults.

The protection depends on the CT configuration and generator grounding arrangement.

Undervoltage Protection (27)

Undervoltage protection monitors generator terminal voltage.

It may be used for:

  • Abnormal system voltage
  • Generator voltage collapse
  • Loss of voltage
  • Backup protection
  • Control and trip logic

Undervoltage protection must be coordinated with generator operating capability and system requirements to avoid unwanted tripping during transient conditions.

Impedance Protection (21)

Where supported and applicable, impedance-based protection can provide backup for system faults.

The measured impedance may be affected by:

  • Generator reactance
  • CT and VT errors
  • Fault type
  • System configuration
  • Fault resistance
  • Generator operating conditions

Impedance protection must be applied with suitable settings and coordination studies.

Thermal Protection (49)

Generator thermal protection may monitor heating conditions using:

  • Current-based thermal models
  • Temperature sensors
  • Winding temperature inputs
  • Cooling system supervision

Thermal protection is important for detecting overloads and cooling system problems.

Overfluxing Protection (24)

Overfluxing protection supervises the voltage-to-frequency ratio.

Excessive V/Hz can cause magnetic saturation and heating in the generator and connected transformers.

This condition may occur due to:

  • Overvoltage
  • Underfrequency
  • Incorrect excitation
  • Abnormal startup conditions
  • Control system problems

10. Generator Protection Settings and Testing

Generator protection settings and testing are essential parts of the protection engineering, commissioning, and maintenance process.

A protection scheme must not only be correctly designed but also verified to ensure that the relay responds properly to simulated operating conditions.

A. Protection Setting Preparation

Before configuring Sepam generator protection, the engineer should collect the required generator and system data.

Generator data

  • Rated power
  • Rated voltage
  • Rated current
  • Frequency
  • Power factor
  • Generator reactances
  • Generator capability curve
  • Thermal withstand limits
  • Negative sequence withstand data
  • Neutral grounding arrangement
  • Excitation system characteristics
  • Manufacturer protection requirements

Instrument transformer data

  • CT ratios
  • CT polarity
  • CT class
  • CT burden
  • VT ratios
  • VT connection
  • VT polarity
  • Measurement circuit configuration

System data

  • Network configuration
  • Short-circuit study
  • Load flow study
  • Generator operating limits
  • Protection coordination study
  • Breaker characteristics
  • Trip circuit configuration
  • Auxiliary DC supply

B. Protection Function Configuration

Protection functions should be configured according to the generator protection philosophy and engineering study.

Typical configuration activities include:

  • Selecting the appropriate Sepam relay application
  • Enabling required protection functions
  • Entering CT and VT ratios
  • Defining generator rated values
  • Configuring measurement parameters
  • Entering protection thresholds
  • Setting operating delays
  • Configuring alarm outputs
  • Configuring trip outputs
  • Mapping protection signals
  • Configuring breaker control and interlocking logic, where applicable

The engineer must confirm the supported functions of the specific Sepam model and the correct configuration software and firmware.

C. Secondary Injection Testing

Secondary injection testing verifies that the protection relay correctly measures and responds to injected signals.

The test equipment injects currents and voltages into the relay input circuits.

Testing may include:

  • Current measurement verification
  • Voltage measurement verification
  • Phase sequence verification
  • Phase angle verification
  • CT polarity checks
  • VT polarity checks
  • Protection pickup tests
  • Operating time tests
  • Directional tests
  • Differential protection tests
  • Negative sequence protection tests
  • Power measurement tests

D. Differential Protection Testing (87G)

Typical testing objectives include:

  • Verify CT ratio scaling
  • Verify current polarity
  • Verify phase association
  • Confirm differential measurement stability
  • Test operating threshold
  • Test restraint characteristic
  • Test high-set operation, if applicable
  • Verify trip logic
  • Confirm alarm and event indications

Testing must be planned to ensure that the protected equipment and other connected circuits are safely isolated where necessary.

E. Stator Earth Fault Testing (64G)

Testing may include:

  • Verify neutral voltage input
  • Verify neutral current input
  • Confirm CT and VT scaling
  • Verify earth fault pickup
  • Confirm time delay
  • Verify alarm operation
  • Verify trip operation
  • Confirm external interlocking

The test method must match the actual stator earth fault protection arrangement.

F. Rotor Earth Fault Protection Testing (64R)

Testing should verify:

  • Insulation monitoring function
  • Detection sensitivity
  • Alarm thresholds
  • Indication and event recording
  • Protection system integrity
  • Alarm/trip logic, as applicable

Specialized rotor earth fault monitoring equipment may require separate testing procedures.

G. Loss of Excitation Testing (40)

Test objectives may include:

  • Verify voltage and current measurement
  • Confirm impedance calculation
  • Verify operating characteristic
  • Test protection zones, if applicable
  • Confirm timing
  • Verify alarm and trip outputs
  • Check excitation and generator trip coordination

Test procedures must consider the relay’s operating characteristic and the excitation system configuration.

H. Reverse Power Testing (32)

Reverse power testing should verify:

  • Active power measurement
  • Correct power direction
  • CT/VT polarity
  • Phase association
  • Pickup threshold
  • Time delay
  • Alarm output
  • Trip output

Power direction must be checked carefully before testing the protection function.

I. Negative Sequence Protection Testing (46)

Testing should verify:

  • Negative sequence current calculation
  • Phase current measurement
  • Unbalance response
  • Pickup threshold
  • Thermal characteristic
  • Time delay
  • Alarm and trip logic

J. Voltage and Frequency Protection Testing

Overvoltage, undervoltage, overfrequency, and underfrequency protection testing should verify:

  • Measurement accuracy
  • Pickup thresholds
  • Operating delays
  • Reset behavior
  • Alarm and trip outputs
  • Coordination with generator operating limits

Generator Protection Commissioning Checklist

ItemVerification
Generator dataRated values correctly entered
CT configurationRatio, polarity, and phase association verified
VT configurationRatio, polarity, and connection verified
Differential protectionStability, pickup, and trip tested
Stator earth faultMeasurement, pickup, and trip tested
Rotor earth faultMonitoring, alarm, and trip philosophy verified
Loss of excitationOperating characteristic and trip logic tested
Reverse powerPower direction and operating threshold tested
Negative sequenceUnbalance calculation and characteristic verified
OvervoltagePickup and timing tested
UndervoltagePickup and timing tested
OverfrequencyPickup and timing tested
UnderfrequencyPickup and timing tested
Backup protectionCoordination and operating logic verified
Trip circuitsContinuity and operation verified
BreakerTrip function and status feedback verified
DC supplyVoltage and circuit integrity checked
Alarm systemIndications and annunciation checked
Event recordsEvent timestamps and logs verified
Disturbance recordsRecording and retrieval verified
Final documentationSettings and test reports completed

Practical Engineering Considerations for Sepam Generator Protection

When applying Sepam protection relays to generator protection, engineers should avoid treating relay settings as generic values. Generator protection settings depend heavily on the machine, grounding system, excitation arrangement, prime mover, power system, and operational requirements.

Important considerations include:

  • Always use generator manufacturer data.
  • Perform protection coordination studies before finalizing settings.
  • Verify CT and VT circuits before enabling protection.
  • Check protection function availability in the selected Sepam model.
  • Ensure protection settings are consistent with the generator capability curve.
  • Confirm trip outputs and interlocking logic.
  • Test protection functions using appropriate relay test equipment.
  • Record the final settings and test results.
  • Review event records and disturbance records after commissioning.
  • Follow approved switching and safety procedures.

Conclusion

Sepam generator protection requires a coordinated combination of electrical fault protection, abnormal operating condition protection, rotor and stator protection, and backup protection.

Generator differential protection, stator earth fault protection, rotor earth fault protection, loss of excitation protection, reverse power protection, negative sequence protection, voltage and frequency protection, and backup protection work together to protect the generator throughout its operating range.

Understanding the operating principles of these functions is essential for engineers responsible for relay configuration, protection studies, commissioning, testing, maintenance, and troubleshooting.

The Sepam Generator Protection series provides a structured reference for understanding these protection functions and applying them in practical generator protection projects.

Practical Training by Elec-Engg

RelaySimTest: OMICRON’s solution for testing the whole protection system with one or more CMC test sets

Elec-Engg provides practical training in power system protection, protection relay configuration, substation automation, relay testing, and commissioning.

Our training programs focus on practical engineering applications, real protection scenarios, configuration workflows, testing procedures, and troubleshooting techniques.

Explore training resources covering:

  • Generator, transformer, feeder, motor, and line protection
  • Protection relay configuration and settings
  • Relay testing and commissioning using Omicron equipment
  • Siemens SIPROTEC relays and DIGSI software
  • ABB protection relays and PCM600
  • Schneider Electric Sepam and Easergy protection relays
  • IEC 61850 and substation automation systems

Visit Elec-Engg to explore our practical protection and substation automation courses, online training programs, and engineering resources.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top