Siemens 7SK80 Motor Protection Relay: Functions, Settings, DIGSI 4 & Testing

Important product-family note: The 7SK80 belongs to the Siemens SIPROTEC Compact family, not the original SIPROTEC 4 range. It is still relevant to this series because it is commonly engineered using DIGSI 4 and is used in motor protection applications. The article below identifies the relay correctly while continuing the wider Siemens protection-relay guide.

Siemens SIPROTEC Compact 7SK80 – Complete Guide to Motor Protection Relay Functions, Settings, Applications and Testing

1. Introduction to the Siemens 7SK80 Motor Protection Relay

The Siemens SIPROTEC Compact 7SK80 is a multifunction numerical protection relay designed primarily for the protection of three-phase asynchronous induction motors. It combines motor-specific protection with general electrical protection, monitoring, control and fault-recording functions.

It can be applied to motors in:

  • Industrial plants and manufacturing facilities
  • Oil, gas and petrochemical installations
  • Water and wastewater pumping stations
  • Power plants and auxiliary systems
  • Mining, cement and steel industries
  • Medium-voltage motor control centres (MCCs)
  • Large low-voltage motor applications, where the instrument-transformer arrangement is suitable

The 7SK80 is designed to protect motors against electrical faults and abnormal operating conditions, including short circuits, earth faults, overload, excessive starting time, locked rotor, phase unbalance and excessive numbers of starts.

The exact protection scope depends on the device configuration, order number, firmware and enabled functions. Siemens’ SIPROTEC Compact catalogue identifies the 7SK80 as a generator and motor protection device. cache.industry.siemens.com+1

2. Main Protection Functions of the 7SK80

The following table summarises important functions available in the 7SK80 family. Some functions are part of the basic functionality, while others depend on the selected configuration.

ANSI codeProtection functionPurpose
50/51Phase overcurrentDetects phase faults and excessive current
50N/51NEarth-fault overcurrentDetects earth faults
50N(s)/51N(s)Sensitive earth-fault protectionDetects low-level earth faults, depending on input configuration
49Thermal overloadProtects motor windings against overheating
46Negative-sequence protectionDetects phase unbalance
48Starting-time supervisionDetects excessive motor starting time
66Restart inhibit / start counterPrevents excessive or premature starts
14Locked-rotor protectionDetects rotor stalling or failure to accelerate
51MLoad-jam protectionDetects mechanical jamming or excessive load
37Undercurrent protectionDetects loss of load or underload
50BFCircuit-breaker failureDetects failure of the breaker to interrupt current
74TCTrip-circuit supervisionMonitors the trip circuit
86LockoutMaintains a trip or lockout condition

Depending on the ordered version, additional functions can include directional earth-fault protection, voltage and frequency protection, phase-sequence monitoring, breaker-wear monitoring and flexible protection functions. cache.industry.siemens.com+2

3. Motor Thermal Overload Protection – ANSI 49

Thermal overload protection is one of the most important functions in a motor protection relay.

A motor can operate above its rated current for a certain period without immediate damage. However, prolonged overload increases winding temperature and can damage the insulation system.

The 7SK80 uses a thermal model to estimate the motor’s thermal condition.

The thermal model considers factors such as:

  • Motor current
  • Rated motor current
  • Thermal time constant
  • Thermal alarm threshold
  • Temperature rise at rated current
  • Cooling behaviour when the motor is stopped
  • Ambient-temperature measurement, if configured

3.1 Thermal replica

The relay calculates a thermal image representing the estimated heating condition of the motor.

When the motor current increases, the thermal image rises. When the motor is stopped or operating at a lower load, the thermal image decreases according to the configured cooling characteristics.

This allows the relay to account for the motor’s previous operating condition rather than treating every overload as an isolated event.

3.2 Important thermal settings

Typical setting parameters include:

ParameterDescription
FCT 49Enables or disables thermal overload protection
49 K-FACTORThermal characteristic factor
TIME CONSTANTThermal time constant
49 Θ ALARMThermal alarm threshold
I ALARMCurrent alarm threshold
Kτ-FACTORTime-constant factor during motor stoppage
T EMERGENCYEmergency-start trip-suppression time
49 TEMP. RISE ITemperature rise at rated current

The exact available settings and ranges must be checked against the relay firmware and configuration. ManualsLib+2

3.3 Thermal alarm and trip

A practical configuration may use two levels:

  • Alarm: Indicates that the motor is approaching its thermal limit.
  • Trip: Disconnects the motor when the calculated thermal condition reaches the configured trip threshold.

An emergency-start input can be configured to suppress the overload trip command for a defined period. This must be engineered carefully: it does not reset the thermal image, and it should only be used where the motor manufacturer’s thermal limits and plant operating philosophy permit it. ManualsLib+1

4. Motor Starting-Time Supervision – ANSI 48

Motor starting is a demanding operating condition. During acceleration, the motor draws a high starting current until it approaches normal operating speed.

If the motor fails to accelerate within the permitted time, the high current can cause excessive heating.

The 7SK80 provides starting-time supervision to detect an excessively long start.

Important parameters include:

  • Starting current relative to rated motor current
  • Maximum permissible starting time
  • Motor rated current
  • Motor starting and running conditions
  • Starting-time supervision logic

4.1 Starting current

The starting current is normally several times the rated motor current. The exact value depends on the motor design, starting method and load.

For example, a motor may have:

  • Rated current: 100 A
  • Starting current: 600 A
  • Starting-current ratio: 6 × rated current

This is only an illustrative example. The actual values must come from the motor data and measured starting behaviour.

4.2 Maximum starting time

The maximum starting time must be coordinated with:

  • Motor manufacturer’s permissible starting time
  • Load torque and inertia
  • Starting method
  • Supply voltage during starting
  • Motor thermal withstand capability
  • Process requirements

If the motor remains in the starting condition beyond the configured limit, the relay can issue an alarm or trip according to the selected configuration.

5. Restart Inhibit and Start Counter – ANSI 66

Repeated motor starts can cause excessive heating, particularly when a motor is started several times within a short period.

The 7SK80 includes motor starting-counter and restart-inhibit functions.

The function can supervise:

  • Maximum number of warm starts
  • Number of cold starts
  • Permitted starts within the configured operating conditions
  • Minimum restart-inhibit time
  • Motor cooling after a previous start

Example

Consider a motor whose manufacturer permits a limited number of consecutive starts.

If the motor has already completed the permitted number of starts, the relay can block another start until the configured conditions are satisfied.

This function is particularly important for:

  • Large pumps
  • Compressors
  • Fans
  • Conveyors
  • Crushers
  • High-inertia motors

The relay’s start-counter settings must be coordinated with the motor manufacturer’s starting and cooling limits. ManualsLib+1

6. Locked-Rotor Protection – ANSI 14

A locked rotor occurs when the motor is energised but the rotor cannot accelerate normally, or when the rotor becomes mechanically blocked during operation.

This condition can produce high current and rapid motor heating.

The 7SK80 includes rotor-overload protection as part of its motor-protection functionality.

Possible causes of locked-rotor conditions include:

  • Mechanical blockage
  • Pump or compressor seizure
  • Bearing failure
  • Excessive load torque
  • Damaged driven equipment
  • Incorrect starting conditions

The protection settings should distinguish between normal motor starting and an abnormal stalled condition.

Incorrect settings may cause unwanted trips during normal acceleration or may fail to detect a genuine locked-rotor condition.

7. Load-Jam Protection – ANSI 51M

Load-jam protection detects abnormal increases in motor current that may indicate a mechanical problem in the driven equipment.

Typical applications include:

  • Conveyor belt systems
  • Pumps
  • Crushers
  • Mixers
  • Fans
  • Industrial machinery

For example, a conveyor motor may normally operate at 70% of rated load. If a mechanical blockage occurs, the motor current may rise significantly.

The load-jam function can detect this condition using a configured current threshold and operating delay.

Important parameters include:

  • Load-jam protection enable/disable
  • Load-jam current threshold
  • Trip delay
  • Alarm current threshold
  • Alarm delay
  • Blocking time after motor start

A starting block is important because high current during normal acceleration should not be interpreted as a mechanical jam. ManualsLib+1

8. Negative-Sequence Protection – ANSI 46

Voltage or current unbalance can cause negative-sequence current to flow in the motor stator.

Negative-sequence current produces additional rotor heating and can damage the motor.

The 7SK80 provides negative-sequence protection to detect this condition.

Possible causes include:

  • Open phase
  • Unequal phase loading
  • Unbalanced supply voltage
  • Defective cable connections
  • Faulty switching equipment
  • Unequal contact resistance

The relay evaluates negative-sequence current and can operate according to the selected characteristic and time delay.

The setting must be coordinated with the motor’s permissible negative-sequence withstand capability.

9. Phase Overcurrent Protection – ANSI 50/51

The 7SK80 provides phase overcurrent protection for detecting excessive phase current.

Typical applications include:

  • Phase-to-phase faults
  • Three-phase short circuits
  • Severe motor overloads
  • Backup protection for downstream faults

Depending on the selected configuration, the relay provides multiple overcurrent stages and definite-time or inverse-time characteristics.

Important settings

SettingDescription
Pickup currentCurrent threshold for operation
Time delayOperating delay
CharacteristicDefinite-time or inverse-time curve
Reset behaviourReturn-to-normal behaviour
Stage enableEnables or disables the relevant stage

The overcurrent protection must be coordinated with:

  • Motor starting current
  • Motor thermal withstand
  • Cable ampacity
  • Upstream protection
  • Downstream protection
  • Short-circuit current levels

A common engineering mistake is to set the instantaneous overcurrent threshold too close to the motor starting current. This can cause unwanted trips during motor acceleration.

10. Earth-Fault Protection – ANSI 50N/51N

Earth faults in motor circuits can result from insulation deterioration, moisture, cable damage or winding insulation failure.

The 7SK80 provides earth-fault protection using the configured residual-current measurement arrangement.

Depending on the hardware and ordered configuration, earth-fault protection may use:

  • Residual current calculated from the three phase CT currents
  • An external earth-current transformer
  • Sensitive earth-fault measurement inputs

Sensitive earth-fault protection is particularly relevant in systems with low earth-fault currents, such as certain isolated-neutral or impedance-earthed networks.

The protection method and settings must match the actual system earthing arrangement.

Important engineering considerations

  • CT ratio and polarity
  • Residual-current measurement method
  • Neutral earthing arrangement
  • Minimum earth-fault current
  • Protection sensitivity
  • Coordination with upstream and downstream earth-fault protection

Directional earth-fault protection may also be available in selected configurations. cache.industry.siemens.com+2

11. Undercurrent Protection – ANSI 37

Undercurrent protection can identify operating conditions in which the motor current falls below a configured threshold.

This can be useful for detecting:

  • Pump running dry
  • Loss of mechanical load
  • Broken coupling
  • Loss of process material
  • Unexpected reduction in motor load

The protection should be configured with an appropriate delay to avoid operation during normal process variations or transient load changes.

12. Voltage and Frequency Protection – ANSI 27, 59 and 81

Depending on the selected hardware and functional configuration, the 7SK80 can provide additional voltage and frequency protection.

ANSI codeFunctionApplication
27UndervoltageDetects low supply voltage
59OvervoltageDetects excessive voltage
81UUnderfrequencyDetects low system frequency
81OOverfrequencyDetects high system frequency
47Phase-sequence monitoringDetects incorrect phase sequence

These functions can be useful for motor supply supervision and system protection. However, they should not be assumed to be available in every 7SK80 hardware variant.

13. Breaker Failure Protection – ANSI 50BF

The breaker-failure function detects situations where a circuit breaker does not interrupt the current after receiving a trip command.

A typical sequence is:

  1. The protection relay detects a fault.
  2. The 7SK80 issues a trip command to the motor circuit breaker.
  3. The relay monitors the current and configured breaker-status conditions.
  4. If the breaker fails to clear the current within the configured time, breaker-failure logic operates.
  5. A backup trip or other configured action is initiated.

The function must be coordinated with the upstream protection and the actual breaker operating time.

14. Trip-Circuit Supervision – ANSI 74TC

Trip-circuit supervision monitors the continuity and availability of the circuit-breaker trip path.

A defective trip circuit may prevent the breaker from opening when a protection function operates.

The supervision arrangement depends on the relay’s binary inputs, external wiring and selected monitoring method.

Typical issues detected through trip-circuit supervision include:

  • Open trip-coil circuit
  • Wiring disconnection
  • Loss of auxiliary DC supply
  • Defective trip-circuit components

15. Engineering the 7SK80 Using DIGSI 4

The 7SK80 is engineered using DIGSI 4.

DIGSI 4 is used for relay configuration, parameterisation, communication setup, monitoring and disturbance-record evaluation.

Typical engineering activities include:

  1. Creating a new project.
  2. Adding the correct 7SK80 device.
  3. Selecting the appropriate device version.
  4. Configuring the protection functions.
  5. Entering CT and VT ratios.
  6. Defining motor rated data.
  7. Configuring binary inputs and outputs.
  8. Assigning trip and alarm signals.
  9. Configuring communication parameters.
  10. Downloading settings to the relay.
  11. Uploading and comparing relay parameters.
  12. Retrieving event and disturbance records.

15.1 Motor data configuration

Correct motor data is essential for reliable protection.

Important information includes:

  • Rated motor power
  • Rated voltage
  • Rated current
  • Rated frequency
  • Starting current
  • Starting time
  • Permissible starts per hour
  • Thermal withstand characteristics
  • Cooling time
  • CT ratios

The relay settings should be based on the motor nameplate, manufacturer documentation, starting studies and actual plant operating conditions.

15.2 Binary inputs and outputs

Binary inputs can be used for external commands and interlocking signals, such as:

  • Motor start indication
  • Motor stop indication
  • Emergency stop
  • External trip
  • External block
  • Reset
  • Emergency-start signal

Binary outputs can be assigned to:

  • Protection trip
  • Thermal alarm
  • General alarm
  • Start-block indication
  • Breaker-failure operation
  • Relay health and watchdog signals

15.3 Communication and IEC 61850

The available communication protocols depend on the ordered communication hardware and firmware.

When engineering a 7SK80 for a substation automation system, check the exact device variant and communication module before designing the integration.

Do not assume that every 7SK80 supports the same Ethernet, IEC 61850 or GOOSE capabilities.

The SIPROTEC Compact family catalogue describes communication and IEC 61850 GOOSE capabilities at family level, but the specific 7SK80 version must be verified before applying these features to a project. cache.industry.siemens.com+1

16. Testing and Commissioning of the 7SK80

Testing and commissioning are essential to confirm that the relay operates correctly and that the protection settings match the motor and installation.

An OMICRON CMC test set with the appropriate test software can be used for secondary injection testing.

16.1 Initial inspection

Before testing, check:

  • Relay model and order number
  • Firmware version
  • Auxiliary supply voltage
  • CT and VT wiring
  • CT polarity
  • Binary input wiring
  • Binary output wiring
  • Trip circuit
  • Communication connections
  • Relay configuration

16.2 Protection function testing

Protection functionSuggested test
50/51Inject phase current above pickup and verify operation
50N/51NInject residual or earth current
49Verify thermal model response and alarm/trip behaviour
46Inject unbalanced three-phase currents
48Simulate motor starting current and excessive starting time
66Test start counting and restart blocking logic
14Verify locked-rotor protection logic
51MSimulate load-jam current and delay
37Reduce current below the configured threshold
50BFSimulate breaker failure conditions
74TCTest trip-circuit supervision
27/59Inject voltage below and above the configured thresholds, if enabled
81Inject frequency below and above the configured thresholds, if enabled

The exact test procedure depends on the enabled functions, wiring arrangement and relay firmware.

16.3 Binary input and output testing

Check that each configured input produces the intended internal signal and that each output operates the correct external circuit.

For example:

  • External motor start command
  • External motor trip
  • Thermal alarm
  • Protection trip
  • Reset command
  • Emergency-start input

16.4 Disturbance-record analysis

After a test or real protection operation, retrieve the disturbance record and review it using SIGRA or the appropriate Siemens analysis tools.

Useful information includes:

  • Phase currents
  • Residual current
  • Voltage waveforms, if available
  • Protection pickup signals
  • Trip command
  • Binary input and output states
  • Operating time
  • Motor starting behaviour

17. Common 7SK80 Problems and Troubleshooting

ProblemPossible causeRecommended checks
Unwanted trip during motor startingIncorrect starting threshold or timeCheck starting current and acceleration time
Thermal overload alarmMotor overload or incorrect thermal parametersVerify rated current, thermal time constant and load
Restart blockedStart counter or thermal inhibit activeCheck start history and restart-inhibit conditions
Earth-fault alarmGenuine earth fault or incorrect CT wiringCheck residual-current circuit and insulation
Negative-sequence alarmSupply unbalance or CT polarity issueCheck phase currents and CT connections
Load-jam tripMechanical blockage or incorrect thresholdCheck driven equipment and load-jam settings
No trip outputOutput assignment or trip-circuit issueCheck logic, binary output and trip wiring
Communication failureIncorrect interface or protocol configurationVerify device order number and communication settings

18. 7SK80 Compared with Other Siemens Motor Protection Relays

The 7SK80 should be considered in the context of the Siemens protection product families.

RelayProduct familyMain application
7SK80SIPROTEC CompactGenerator and motor protection
7SK81SIPROTEC CompactGenerator and motor protection with low-power current-transformer applications
7SK82SIPROTEC 5Motor protection
7SJ80SIPROTEC CompactOvercurrent and feeder protection
7SJ82SIPROTEC 5Overcurrent and feeder protection

The 7SK80 is especially relevant when maintaining existing SIPROTEC Compact installations or engineering replacement and retrofit projects. The 7SK82 belongs to the newer SIPROTEC 5 family and uses a different engineering environment.

19. Practical Training on Siemens 7SK80 Motor Protection

Understanding a motor protection relay requires more than knowing the ANSI function numbers. Engineers should understand the motor’s starting characteristics, thermal limits, CT circuits, protection coordination and trip logic.

Elec-Engg provides practical training on Siemens protection relays and motor protection engineering, including:

  • Siemens SIPROTEC Compact 7SK80
  • Siemens SIPROTEC 5 motor protection relays
  • Motor protection functions and coordination
  • Thermal overload and motor starting calculations
  • Locked-rotor and load-jam protection
  • CT selection, wiring and polarity checks
  • DIGSI 4 configuration and parameterisation
  • Binary input/output configuration
  • Relay testing using OMICRON CMC
  • Disturbance-record analysis using SIGRA
  • Protection commissioning and troubleshooting

Training is available through:

  • Online training courses
  • Structured self-paced training
  • Customized training for companies and utilities
  • Face-to-face practical training
  • In-house training for protection, commissioning and maintenance engineers

For more information, visit Elec-Engg: https://elec-engg.com/

20. Conclusion

The Siemens SIPROTEC Compact 7SK80 is a multifunction motor protection relay combining thermal overload, starting-time supervision, restart inhibit, locked-rotor, load-jam, negative-sequence, overcurrent and earth-fault protection.

Correct application requires an understanding of the motor’s electrical and thermal characteristics, starting conditions, system earthing arrangement and circuit-breaker operating time.

For engineers working with existing Siemens motor protection installations, practical knowledge of DIGSI 4, protection settings, secondary injection testing and disturbance-record analysis is essential for reliable commissioning and maintenance.

  • Siemens 7SK80
  • SIPROTEC Compact 7SK80
  • Siemens motor protection relay
  • 7SK80 manual
  • 7SK80 settings
  • 7SK80 DIGSI 4
  • Motor thermal overload protection ANSI 49
  • Motor starting-time protection ANSI 48
  • Motor restart inhibit ANSI 66
  • Locked-rotor protection ANSI 14
  • Motor negative-sequence protection ANSI 46
  • Load-jam protection ANSI 51M
  • Motor earth-fault protection
  • Siemens motor relay testing
  • OMICRON motor protection testing
  • SIPROTEC Compact relay commissioning

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top