Siemens SIPROTEC 4 7VU683: High-Speed Motor Bus Transfer (HSBT) Guide

Table Of Contents
  1. 1. Overview of SIPROTEC 4 7VU683
  2. 2. Why Is High-Speed Motor Bus Transfer Necessary?
  3. 3. Typical 7VU683 Applications
  4. 4. Typical Busbar Transfer Arrangement
  5. 5. Understanding Residual Voltage on a Motor Bus
  6. 6. High-Speed Bus Transfer Operating Modes
  7. 7. Transfer Modes Compared
  8. 8. Switching Sequences
  9. 9. Supported Primary Busbar Configurations
  10. 10. Starting Conditions for High-Speed Bus Transfer
  11. 11. Voltage and Current Measurement
  12. 12. Important 7VU683 Settings
  13. 13. Protection Functions for the Tie Circuit Breaker
  14. 14. Monitoring and Supervision Functions
  15. 15. DIGSI 4 Engineering and Configuration
  16. 16. CFC Logic and Substation Automation
  17. 17. Testing and Commissioning of SIPROTEC 4 7VU683
  18. 18. Common 7VU683 Problems and Troubleshooting
  19. 19. 7VU683 Compared with Other SIPROTEC 4 Relays
  20. 20. Practical Training on SIPROTEC 4 7VU683 and Motor Bus Transfer
  21. 21. Conclusion

The Siemens SIPROTEC 4 7VU683 is a specialized high-speed motor bus transfer device designed to transfer motor loads from a failed or unavailable power source to an alternative supply.

It is particularly important in power plants and large industrial facilities where many induction motors are connected to common auxiliary busbars. Examples include thermal power stations, combined-cycle plants, petrochemical facilities, refineries, cement plants and steel industries.

When the normal supply fails, motors continue rotating and generate residual voltage on the busbar. Connecting the busbar to an alternative source at an unsuitable instant can create high electrical and mechanical stress.

The 7VU683 evaluates voltage, frequency, phase angle and other transfer conditions to select an appropriate switching sequence and help achieve a fast, controlled transfer.

Siemens SIPROTEC 4 7VU683 – Complete Guide to High-Speed Motor Bus Transfer (HSBT), Settings, Operating Modes and Testing

This guide covers the 7VU683 architecture, high-speed bus transfer principles, transfer modes, switching sequences, settings, DIGSI 4 engineering, protection functions and commissioning tests.

1. Overview of SIPROTEC 4 7VU683

The 7VU683 is a High-Speed Motor Bus Transfer (HSBT) device within the Siemens SIPROTEC 4 family.

Its main purpose is to maintain the power supply to motor loads by transferring a motor bus from one source to another when the normal source becomes unavailable.

Typical functions include:

  • High-speed motor bus transfer.
  • Voltage and frequency measurement.
  • Residual voltage evaluation.
  • Phase-angle difference measurement.
  • Fast transfer and real-time fast transfer.
  • In-phase transfer.
  • Residual-voltage transfer.
  • Long-time transfer.
  • Automatic and manual transfer initiation.
  • Parallel, simultaneous and sequential switching sequences.
  • Circuit breaker closing-time compensation.
  • Protection functions for the bus-tie circuit breaker in supported configurations.
  • Voltage transformer circuit supervision.
  • Programmable logic using CFC.
  • Event and disturbance-related measurements.

The device is engineered for specific busbar arrangements, including single busbar with two circuit breakers, sectionalized single busbar with three circuit breakers, and single busbar with three circuit breakers. cache.industry.siemens.com+1

2. Why Is High-Speed Motor Bus Transfer Necessary?

Large industrial plants and power stations often have many induction motors connected to auxiliary busbars.

Examples include:

  • Boiler feed water pumps.
  • Cooling water pumps.
  • Condensate pumps.
  • Induced-draft fans.
  • Forced-draft fans.
  • Pulverizer and mill motors.
  • Compressor motors.
  • Process pumps.
  • Cooling tower fans.

When the normal power source is interrupted, the motors do not stop immediately. Their rotating magnetic fields and mechanical inertia produce a decaying residual voltage on the busbar.

This residual voltage has its own magnitude, frequency and phase angle.

If the alternative supply is connected while the residual voltage is significantly out of phase with the incoming source, the resulting electrical transient can produce high current and mechanical torque.

Potential consequences include:

  • High motor starting current.
  • Mechanical shaft and coupling stress.
  • Voltage dips across the alternative source.
  • Protection operation.
  • Process interruption.
  • Damage to motor windings or driven equipment.

The purpose of the 7VU683 is to evaluate the electrical conditions and select an appropriate transfer method to reduce these risks while restoring supply as quickly as the conditions allow. cache.industry.siemens.com+1

3. Typical 7VU683 Applications

3.1 Thermal power stations

Power station auxiliary systems contain many motors that support boiler, turbine and generator operation.

The 7VU683 can transfer the auxiliary motor bus from the normal supply to an alternative source when the normal supply fails.

3.2 Combined-cycle power plants

Gas turbine and steam turbine auxiliary systems require reliable electrical supply for pumps, fans and other essential equipment.

Fast bus transfer can help maintain auxiliary power availability during supply disturbances.

3.3 Petrochemical and refinery plants

Process continuity is important in refineries and petrochemical facilities. A motor bus transfer scheme can help restore the supply of essential process motors following a source failure.

3.4 Cement and steel industries

Large motors operate crushers, mills, fans, compressors and conveyors. The 7VU683 can be applied to suitable busbar configurations to transfer these loads to an alternative source.

3.5 Industrial utility systems

The device is also relevant to industrial plants with two incoming supplies and a bus-tie circuit breaker.

The exact application must be checked against the busbar arrangement and the device’s supported configuration. cache.industry.siemens.com+1

4. Typical Busbar Transfer Arrangement

A typical motor bus transfer scheme has two incoming supplies and a bus-tie circuit breaker.

For example:

  • Source 1 supplies Busbar 1 through CB1.
  • Source 2 supplies Busbar 2 through CB2.
  • CB3 connects the two busbar sections.
  • Motors are connected to the busbar sections.
  • The 7VU683 monitors the relevant electrical quantities and controls the transfer sequence.

A simplified operating example:

  1. Source 1 supplies the motor bus during normal operation.
  2. Source 1 fails or becomes unsuitable.
  3. The 7VU683 detects the configured starting condition.
  4. The normal source circuit breaker is opened, if required by the selected sequence.
  5. The device evaluates the residual bus voltage and transfer conditions.
  6. It determines the suitable transfer mode.
  7. The alternative source circuit breaker or bus-tie breaker is closed according to the configured sequence.
  8. The motor bus is supplied from the alternative source.

The exact switching sequence depends on the primary busbar diagram, transfer direction and selected operating mode. cache.industry.siemens.com+1

5. Understanding Residual Voltage on a Motor Bus

Residual voltage is one of the most important concepts in high-speed motor bus transfer.

When the supply to induction motors is interrupted, the motors continue rotating due to mechanical inertia.

The rotating motors behave temporarily like generators and maintain a voltage on the disconnected busbar.

This voltage gradually decreases as the motors slow down and their magnetic flux decays.

The residual voltage has three important characteristics:

  • Magnitude.
  • Frequency.
  • Phase angle.

The residual frequency may differ from the alternative source frequency because the motors are slowing down.

The phase angle also changes with time because of the frequency difference between the residual voltage and the incoming source.

The 7VU683 evaluates these quantities to determine whether the alternative source can be connected immediately or whether a different transfer mode should be used.

Important: Residual voltage is not necessarily zero immediately after the normal source is disconnected. A busbar may still have a significant voltage even though its incoming circuit breaker is open. cache.industry.siemens.com+1

6. High-Speed Bus Transfer Operating Modes

The 7VU683 supports several transfer modes. The selection depends on the measured electrical conditions and the configured transfer philosophy.

6.1 FAST Mode

Fast transfer aims to connect the motor bus to the alternative source before the residual voltage phase angle becomes unsuitable.

The device evaluates the voltage and phase-angle conditions and issues the closing command when the configured criteria are fulfilled.

Fast transfer is useful when the transfer can be completed shortly after the original source is disconnected.

6.2 REAL-TIME FAST Mode

Real-time fast transfer is an enhanced fast-transfer method.

The device evaluates the changing electrical quantities and the expected switching instant, including circuit breaker operating time.

The aim is to improve the timing of the transfer and reduce the effect of the residual voltage on the motor bus.

6.3 IN-PHASE Mode

In-phase transfer is used when an immediate fast transfer is not possible but the residual voltage and alternative source are expected to reach a suitable phase relationship.

The device monitors the phase-angle difference and frequency difference and calculates an appropriate closing instant.

The transfer is performed when the configured in-phase conditions are satisfied.

6.4 RES-VOLT Mode

Residual-voltage transfer permits closing after the residual voltage has decreased below a configured threshold.

This method can be used when fast or in-phase transfer is not available or has not been successful.

The residual voltage must be sufficiently low according to the application settings.

6.5 LONG-TIME Mode

Long-time transfer is intended for cases where the other transfer methods cannot complete the transfer within their permitted conditions.

The device waits for the configured conditions and then performs the transfer according to the long-time strategy.

The selection of transfer modes and their parameters must be coordinated with the motor characteristics, alternative source capability and plant operating philosophy. cache.industry.siemens.com+2

7. Transfer Modes Compared

Transfer modeMain principleTypical objective
FASTClose quickly under acceptable phase conditionsMinimize supply interruption
REAL-TIME FASTEvaluate the actual changing conditions and switching timeImprove transfer timing
IN-PHASEWait for a suitable phase relationshipReduce switching stress
RES-VOLTWait until residual voltage decreasesAvoid closing at high residual voltage
LONG-TIMETransfer after longer delay under configured conditionsRestore supply when faster modes are unavailable

Not every mode will be suitable for every plant. The selected transfer philosophy should be based on motor ride-through capability, process requirements, network conditions and equipment limitations.

8. Switching Sequences

The 7VU683 supports different switching sequences for controlling the circuit breakers.

8.1 PARALLEL Sequence

In a parallel sequence, the switching operation is arranged so that the alternative source can be connected before the normal source is fully disconnected, according to the configured scheme.

This can reduce the interruption time but requires careful consideration of source paralleling.

The two sources must be suitable for parallel operation, and the protection and interlocking scheme must permit it.

8.2 SIMULTANEOUS Sequence

In a simultaneous sequence, the relevant circuit breaker commands are issued as part of a coordinated switching operation.

The exact timing and breaker logic depend on the selected busbar arrangement.

8.3 SEQUENTIAL Sequence

In a sequential sequence, the circuit breakers operate one after another according to the configured switching logic.

For example, the normal source breaker may open first, followed by the alternative source or bus-tie breaker closing.

The sequence must prevent an unintended parallel connection when the power system is not designed to operate in parallel.

The selected sequence must be verified against the actual primary single-line diagram and circuit breaker interlocking scheme. cache.industry.siemens.com+1

9. Supported Primary Busbar Configurations

The 7VU683 manual describes three principal busbar arrangements.

9.1 Single Busbar with 2 Circuit Breakers

This arrangement is used where a motor bus has two possible incoming sources.

The transfer logic selects the appropriate source and controls the relevant breakers.

9.2 Sectionalized Single Busbar with 3 Circuit Breakers

This arrangement has two busbar sections and a bus-tie circuit breaker.

Each section has its own incoming supply, and the tie breaker connects the two sections.

The 7VU683 can control transfer operations between the sections according to the configured transfer direction.

9.3 Single Busbar with 3 Circuit Breakers

The device also supports a single busbar arrangement with three circuit breakers, according to the supported configuration and application logic.

For every arrangement, the engineering must include the correct circuit breaker status signals, source voltage measurements and transfer direction settings. cache.industry.siemens.com+1

10. Starting Conditions for High-Speed Bus Transfer

A transfer operation must not start simply because a voltage measurement decreases.

The 7VU683 supports several starting conditions, including:

  • Normal-condition start.
  • Fault-condition start.
  • Inadmissible undervoltage.
  • Inadmissible underfrequency.
  • Excessive rate of change of frequency (df/dt).
  • Reverse power.
  • Inadvertent circuit breaker opening.
  • External start commands.

The selected starting conditions depend on the busbar arrangement and application.

For example, an undervoltage start can detect loss of the normal source, while an external binary input can initiate a transfer following a command from another protection or control system.

Current measurement can also be used as an additional criterion in selected starting arrangements. cache.industry.siemens.com+1

11. Voltage and Current Measurement

The 7VU683 uses voltage measurements to evaluate the busbar and alternative source conditions.

The Siemens manual describes the following general measurement arrangement:

  • Three-phase busbar voltage measurement.
  • Single-phase line-side voltage measurement.
  • Single-phase line current measurement for selected starting criteria.
  • Three-phase bus current measurement where required by the configured tie-breaker protection application.

The line-side voltage can be measured using a phase-to-earth or phase-to-phase voltage, depending on the configured VT connection.

The manual also describes applications where the line voltage is taken from the high-voltage side of an incoming transformer. In that case, voltage magnitude and angle compensation parameters are used to account for the transformer ratio and phase displacement.

Correct VT polarity, phase assignment, transformer compensation and CT wiring are essential for reliable transfer operation. Manualzz+1

12. Important 7VU683 Settings

The 7VU683 has a large number of settings covering power system data, busbar configuration, transfer modes, starting conditions, circuit breaker control and protection functions.

The following table gives examples of important engineering parameters. The complete setting list and addresses should be checked in the applicable firmware manual.

Setting areaPurpose
Primary DiagramSelects the supported busbar arrangement
Switching DirectionDefines the transfer direction
Transfer ModeSelects the transfer operating strategy
Switching SequenceSelects parallel, simultaneous or sequential operation
Start ConditionsDefines the conditions that initiate transfer
UminUndervoltage threshold
fminUnderfrequency threshold
df/dtRate-of-change-of-frequency criterion
Residual VoltageThreshold for residual-voltage transfer
Phase Angle DifferencePermitted phase-angle difference
Frequency DifferencePermitted frequency difference
CB Closing TimeCompensates for breaker operating time
Transfer TimeDefines time limits for the transfer process
Voltage Balancing FactorCorrects voltage magnitude for selected VT arrangements
Voltage Angle AdjustmentCompensates for transformer phase displacement

These settings should not be copied from another installation without checking the motor bus characteristics, supply system and circuit breaker data. cache.industry.siemens.com+1

13. Protection Functions for the Tie Circuit Breaker

In addition to high-speed bus transfer, the 7VU683 includes protection functions for the tie circuit breaker in supported busbar configurations.

The Siemens manual describes these functions specifically for the sectionalized single busbar arrangement with three circuit breakers.

Available functions include:

13.1 Phase Overcurrent Protection – ANSI 50/51

The device provides two stages of definite-time phase overcurrent protection for the tie circuit breaker.

The functions can detect excessive phase current and issue a trip command according to the configured pickup and time delay.

13.2 Earth Overcurrent Protection – ANSI 50N/51N

The earth overcurrent protection also includes two definite-time stages.

The residual current can be derived from the configured current measurement arrangement.

13.3 Switch-Onto-Fault Protection

Switch-onto-fault protection is intended to detect a fault when a circuit breaker energizes a busbar or circuit that is already faulted.

The 7VU683 includes phase and earth overcurrent protection for this purpose, with a configurable active time after breaker closing.

13.4 Voltage Control

The protection functions can include voltage control or voltage restraint according to the configured protection logic.

The manual also describes zero-sequence voltage control for earth overcurrent protection.

These protection functions should not be confused with a complete dedicated busbar differential protection scheme. The 7VU683’s integrated protection is intended for its specified tie-breaker applications. cache.industry.siemens.com+2

14. Monitoring and Supervision Functions

Reliable transfer requires correct measurement circuits and circuit breaker status information.

The 7VU683 includes monitoring functions such as:

  • Busbar voltage transformer circuit supervision.
  • Line voltage transformer circuit supervision.
  • Phase-sequence monitoring.
  • Voltage measurement supervision.
  • Circuit breaker status monitoring.
  • Transfer readiness monitoring.
  • Alarm and event indications.

VT circuit supervision is particularly important because an incorrect voltage measurement can affect transfer decisions.

The device manual explains that VT circuit failure supervision must be checked during commissioning, including the blocking behavior of functions that depend on the affected voltage signals. cache.industry.siemens.com+1

15. DIGSI 4 Engineering and Configuration

The SIPROTEC 4 7VU683 is configured using DIGSI 4.

A typical engineering procedure includes:

  1. Create a new DIGSI 4 project.
  2. Insert the correct 7VU683 device.
  3. Verify the device order number and hardware configuration.
  4. Configure the primary busbar diagram.
  5. Configure the transfer direction.
  6. Configure the circuit breaker assignments.
  7. Enter nominal voltage and frequency data.
  8. Configure the VT and CT connections.
  9. Configure voltage balancing and angle compensation where required.
  10. Select the transfer operating modes.
  11. Configure the switching sequence.
  12. Configure transfer starting conditions.
  13. Enter circuit breaker closing times.
  14. Configure tie-breaker protection functions.
  15. Assign binary inputs and outputs.
  16. Configure indications, alarms and event messages.
  17. Configure CFC logic if additional logic is required.
  18. Transfer the settings to the relay and verify the configuration.

The configuration must match the actual single-line diagram. Incorrect breaker assignment or status feedback can cause the transfer logic to operate incorrectly.

The 7VU683 also supports remote ON/OFF control of selected functions over communication, when the corresponding parameter is enabled. cache.industry.siemens.com+1

16. CFC Logic and Substation Automation

The 7VU683 includes programmable logic using CFC (Continuous Function Chart).

CFC can be used to implement additional logic and generate user-defined indications.

Typical engineering applications include:

  • Additional transfer permissives.
  • External blocking conditions.
  • Plant operating mode selection.
  • Alarm aggregation.
  • Interlocking signals.
  • External start and stop logic.
  • Transfer-ready indications.
  • Interface logic with the plant control system.

The device’s communication interfaces can also be used for integration with a substation automation or plant control system. The available protocols and communication hardware depend on the device variant.

For practical engineering, the complete transfer logic should be documented in a cause-and-effect diagram or functional logic diagram before being implemented in DIGSI 4.

17. Testing and Commissioning of SIPROTEC 4 7VU683

Commissioning a 7VU683 is more involved than testing a conventional overcurrent relay. The complete transfer sequence must be verified, including voltage measurements, starting conditions, circuit breaker logic, transfer modes and output commands.

A suitable secondary injection test set, such as an OMICRON CMC, can be used for measurement and functional testing.

17.1 Check Device Hardware and Wiring

Verify:

  • Auxiliary supply.
  • Protective earth connection.
  • CT wiring.
  • VT wiring.
  • Binary input circuits.
  • Binary output circuits.
  • Circuit breaker trip and close circuits.
  • Communication connections.
  • Device indications and LEDs.

17.2 VT Circuit Testing

Verify the voltage circuits for:

  • Correct VT ratio.
  • Polarity.
  • Phase sequence.
  • Phase assignment.
  • Busbar voltage.
  • Line voltage.
  • Transformer ratio compensation.
  • Transformer phase-angle compensation, where applicable.

17.3 CT Circuit Testing

Verify CT polarity, ratio and phase assignment.

If current measurement is used for transfer starting or tie-breaker protection, confirm that the measured values correspond to the actual primary current direction.

17.4 Starting Condition Testing

Test each enabled starting condition separately.

Examples include:

  • Undervoltage.
  • Underfrequency.
  • Rate of change of frequency.
  • Reverse power.
  • Fault-condition start.
  • External binary start.
  • Inadvertent circuit breaker opening.

Verify the start indications and confirm that the transfer sequence begins only when the required conditions are fulfilled.

17.5 FAST Mode Testing

Simulate the loss of the normal source and verify the transfer logic.

Check:

  • Start detection.
  • Opening command.
  • Voltage and phase-angle evaluation.
  • Closing command.
  • Transfer completion indication.
  • Circuit breaker feedback.

17.6 IN-PHASE Mode Testing

Inject voltage signals with a controlled phase-angle difference and frequency difference.

Verify that the device evaluates the changing phase angle and issues the closing command when the configured in-phase conditions are fulfilled.

17.7 RES-VOLT Mode Testing

Simulate a decaying residual voltage by gradually reducing the bus voltage.

Verify the configured residual-voltage threshold and the closing permissive.

17.8 Circuit Breaker Closing-Time Test

Measure the actual operating time of the relevant circuit breakers.

Compare the measured values with the configured closing-time parameters.

17.9 Tie-Breaker Protection Testing

If tie-breaker protection is enabled, test:

  • Phase overcurrent stage 1.
  • Phase overcurrent stage 2.
  • Earth overcurrent stage 1.
  • Earth overcurrent stage 2.
  • Phase switch-onto-fault protection.
  • Earth switch-onto-fault protection.
  • Associated voltage control.
  • Trip outputs and alarms.

17.10 Complete Transfer Sequence Test

Finally, simulate the complete transfer sequence according to the approved commissioning procedure.

Verify that the actual breaker operations, device indications and control-system signals match the approved switching philosophy.

Important safety requirement: Functional tests involving circuit breaker outputs must be performed with appropriate isolation and switching safeguards. Never allow an unintended parallel connection between independent sources during testing.cache.industry.siemens.com+1

18. Common 7VU683 Problems and Troubleshooting

ProblemPossible causeRecommended check
Transfer does not startStarting condition not fulfilledCheck voltage, frequency and external start signals
Incorrect bus voltage measurementVT wiring or configuration errorVerify phase sequence, polarity and ratio
Transfer blockedBlocking input or transfer readiness conditionCheck block signals and device indications
FAST transfer unsuccessfulPhase angle or closing conditions outside limitsReview measured values and transfer criteria
IN-PHASE transfer takes too longFrequency difference or phase movement unsuitableCheck slip frequency and configured limits
RES-VOLT transfer does not occurResidual voltage remains above thresholdCheck voltage measurement and residual-voltage setting
Alternative breaker does not closeInterlock, output assignment or breaker feedback issueCheck closing circuit and binary output logic
Wrong transfer directionIncorrect switching-direction configurationVerify the primary diagram and direction settings
Incorrect transformer voltage comparisonMissing magnitude or angle compensationCheck voltage balancing factor and angle adjustment
Tie-breaker trips unexpectedlyProtection pickup or switch-onto-fault logicReview protection records and settings
Transfer-ready signal missingCircuit breaker status or voltage circuit supervisionCheck breaker feedback and VT supervision
Control system does not receive alarmCommunication or indication mapping issueCheck protocol configuration and signal mapping

19. 7VU683 Compared with Other SIPROTEC 4 Relays

The 7VU683 has a specialized role and should not be confused with ordinary protection relays.

RelayMain application
7VU683High-speed motor bus transfer
7VK61Circuit breaker management
7VE61 / 7VE63Automatic synchronizing
7SS52Busbar differential protection
7SJ6Feeder and overcurrent protection
7SA6Distance protection
7UT6Transformer differential protection
7UM6Generator protection

A typical power plant may use several of these devices together. For example, the 7VU683 handles the auxiliary motor bus transfer, while separate relays protect generators, transformers, feeders and busbars.

20. Practical Training on SIPROTEC 4 7VU683 and Motor Bus Transfer

Elec-Engg provides practical training in power system protection, Siemens SIPROTEC relays, substation automation, relay testing and commissioning.

Training topics can include:

  • SIPROTEC 4 7VU683 device configuration.
  • High-speed motor bus transfer principles.
  • Residual voltage and phase-angle evaluation.
  • FAST, REAL-TIME FAST, IN-PHASE and RES-VOLT modes.
  • Switching sequences and transfer logic.
  • DIGSI 4 engineering.
  • CFC logic development.
  • Binary input and output configuration.
  • Tie-breaker protection functions.
  • OMICRON secondary injection testing.
  • Practical commissioning and troubleshooting.

Training delivery options include online courses, structured self-paced training, customized training for companies and utilities, and face-to-face practical sessions.

Visit Elec-Engg for practical courses by Dr Saeed Roostaee / Elec-Engg

  • Siemens 7VU683 relay
  • SIPROTEC 4 7VU683 manual
  • High-speed bus transfer
  • High-speed motor bus transfer
  • HSBT protection
  • Motor bus transfer relay
  • Power plant auxiliary bus transfer
  • Residual voltage transfer
  • Fast bus transfer
  • Real-time fast transfer
  • In-phase bus transfer
  • Residual voltage mode
  • DIGSI 4 7VU683
  • Motor bus transfer testing
  • OMICRON 7VU683 testing
  • Bus transfer commissioning
  • Power plant protection
  • Siemens protection relay training

21. Conclusion

The Siemens SIPROTEC 4 7VU683 is a specialized high-speed motor bus transfer device developed for power plants and industrial facilities with large motor loads.

Its main purpose is to restore the electrical supply to motor busbars after a source failure while considering residual voltage, frequency, phase angle and circuit breaker operating time.

Understanding the transfer modes, switching sequences, starting conditions, protection functions, DIGSI 4 configuration and commissioning procedures is essential for engineers responsible for power plant auxiliary systems and industrial power distribution.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top