Overcurrent and Earth Fault Protection

Config and testing of the generator, transformer, line, and motor protection functions

Course Title & Dates

Config and testing of the generator, transformer, line, and motor protection functions
4 days

Trainer Profile

Dr. Saeed Roostaee, technical trainer in protection relay IEDs, IEC 61850, and Substation Automation
https://elec-engg.com/saeed-roostaee/

Registration

email: saeed61850@gmail.com

Tentative Course Schedule

Day 1

TIME	TRAINING SCHEDULE & TOPICS
9.00am – 10.30am	ABB relays, PCM 600 installation, Connectivity pack installation, Hardware configuration, Application configuration, Signal matrix Parameter setting, IED read and write IED online monitoring and signal monitoring Disturbance, and event viewer
10.30 am – 10.45 am	TEA BREAK
10.45am –1.00pm	SIPROTEC 5 relay families and applications DIGSI 5 and device driver installation SIPROTEC 5 configurator Relay configuration
1.00pm – 2.00pm	LUNCH
2.00pm –3.30pm	SIPROTEC 4 Relay families DIGSI 4 installation Masking I/O CFC Fault Recorder
3.30pm – 3.45pm	TEA BREAK
3.45pm – 5.00pm	MiCOM relays range, naming, and application Easergy Software Configuration and PSL Event and disturbance recorder

Day 2

TIME	TRAINING SCHEDULE & TOPICS
9.00am – 10.30am	OMICRON CMC Test universe softwareAMT105 AMPro software signal view, impedance view, vector view different types of test modulesRIO, XRIO, and PTL
10.30 am – 10.45 am	TEA BREAK
10.45am – 1.00pm	Principle of Differential Protection87G Generator Differential Protection87T Trans. Differential Protection87M Motor Differential Protection87L Line Differential Protection
1.00pm – 2.00pm	LUNCH
2.00pm – 3.30pm	Testing of the Differential protection function (87G, 87T, 87M, 87L) Operating CharacteristicDifferential ConfigurationDifferential trip time-harmonic
3.30pm – 3.45pm	TEA BREAK
3.45pm – 5.00pm	81O Over frequency Protection81U Under frequency Protection59 Overvoltage Protection27 Under voltage ProtectionTesting of the Over/under frequency (81O/ 81U)Testing of the Over/Under voltage (59, 27)

contact us to reserve your seat

Day 3

TIME	TRAINING SCHEDULE & TOPICS
9.00am – 10.30am	50/51 Overcurrent protection50N/51N earth fault protection 67/67N Directional/ directional earth fault protectionRelay coordination
10.30 am – 10.45 am	TEA BREAK
10.45am – 1.00pm	Overcurrent test moduleOvercurrent RIO block settings of the Overcurrent test module testing of the Overcurrent and Directional Overcurrent Functions (67, 67N, 50, 51, 50N, 51N)
1.00pm – 2.00pm	LUNCH
2.00pm – 3.30pm	46 Negative Phase Sequence Protection51V Voltage-Dependent O/C Protection49S Stator Overload Protection49R Overload Protection48 Motor starting time supervision51L lock rotor
3.30pm – 3.45pm	TEA BREAK
3.45pm – 5.00pm	Testing of the Negative Phase Sequence ProtectionTesting of the ANSI 51V Voltage-Dependent O/C ProtectionTesting of the ANSI 49 Overload Protection

Day 4

TIME	TRAINING SCHEDULE & TOPICS
9.00am – 10.30am	Distance protection line simulation in PSCADTesting of the fault location function
10.30 am – 10.45 am	TEA BREAK
10.45am – 1.00pm	21 Line distance protection40G Field Failure Protection21G Generator Under impedance Protection78 Pole Slipping Protection
1.00pm – 2.00pm	LUNCH
2.00pm – 3.30pm	Distance RIO block shot Test, Check Test, Search Test, Z\t Diagram, Zone SettingsTesting of the Distance function (21)Testing of the 40G Field Failure Protection
3.30pm – 3.45pm	TEA BREAK
3.45pm – 5.00pm	64S Generator, 95% &100% Stator Earth Fault Protection, 51/27 Generator, Dead Machine Protection, 24G Generator, Over flux Protection, 47G Generator, Fuse Failure Supervision, 32R Generator, Reverse Power Protection

MiCOM Relays Training Package

MICOM P123 protection relay has been made to control and protect current and ground faults for overhead and cable lines, and MICOM P441 is one of the distance relays that’s responsible for protection control and monitoring of transmission lines.

Through this course, you can learn how to configure and work with these relays.

Online video training
Trainer: Dr. Saeed Roostaee (Profile)
4 hrs pre-recorded videos + 4 hrs attached supplementary videos on google drive + data models + PDF files

Part 01: MiCOM relays range, naming, and application

Parts 2-7: exercises with MiCOM P123 and AMT105 setup. Three-phase signals are injected into the relay to test hardware connection and protection functions.

Parts 8-17: exercises with MiCOM P441 and AMT105 (configuration and PSL, event and disturbance recorder, overcurrent protection, voltage protection, negative sequence protection, and distance protection parameters)

MiCOM Relays Training

€45

Rated 4.50 out of 5 based on 4 customer ratings

Add to cart

Supplementary files attached

01- start working with Easergy Studio in online mode
02- MiCOM Relay Measurements, Event Logs & Disturbance Records
03- Input naming in the Micom relays
04- Communicate with MiCom P139
05- Communicating with MICOM P139 checking the parameters from the front panel
06- Binary input test from MICOM P139 front panel
07- Binary input test from MICOM P139 front Easergy studio
08 Function Parameters in the MICOM P139
09- Overcurrent Function test in the Micom P139
10- Inverse time overcurrent function IDMT test in the MiCOM P139
11- CBF function config and parameters in the Micom P139
12- Autorecoser function config in the MiCOMp139
13- Autorecoser function test in the MiCOMp139
14- Autorecoser function test in the MiCOMp139 By FREJA
15- Under and Over Voltage protection function parameters and testing in the MiCOM P443
16- Overcurrent and Earth Fault protection function parameters and testing in the MiCOM P443
17- DEF protection function parameters and testing in the MiCOM P443
18- Auto recloser function test in the MiCOM P546
19- Trip Scheme in the Micom P546
20- SOTF in the Micom P546
21- MICOM P546 Differential protection test
22- MICOM P546 Syncro Check