GE Multilin Transformer Differential Protection (ANSI 87T): T60 and 845, CT Compensation, Bias Characteristics, Inrush Restraint and Commissioning

Table Of Contents
  1. 1. Introduction
  2. 2. What Is Transformer Differential Protection?
  3. 3. GE Multilin Transformer Protection Relays
  4. 4. Transformer Differential Protection Zone
  5. 5. Transformer Differential Current and Restraint Current
  6. 6. CT Ratio Matching and Transformer Ratio Compensation
  7. 7. Transformer Vector Group Compensation
  8. 8. Transformer Tap-Changer Effects
  9. 9. Magnetizing Inrush and Differential Protection Stability
  10. 10. Overexcitation and the Fifth Harmonic
  11. 11. Restricted Earth-Fault Protection (ANSI 64REF)
  12. 12. Transformer Differential Protection Settings
  13. 13. Practical Transformer Differential Example
  14. 14. GE Multilin EnerVista Configuration Workflow
  15. 15. Testing GE Multilin Transformer Differential Protection
  16. 16. Common Transformer Differential Protection Problems
  17. 17. Practical Commissioning Checklist
  18. 18. Engineering Recommendations
  19. 19. Conclusion
  20. 20. Training on GE Multilin Transformer Protection by Elec-Engg

1. Introduction

Power transformers are among the most important and expensive assets in electrical power systems. A serious internal transformer fault can cause extensive equipment damage, fire, prolonged outages, and significant financial losses.

Transformer differential protection, identified by ANSI device number 87T, is one of the principal protection methods used to detect internal faults within a transformer protection zone.

GE Multilin provides transformer protection solutions in selected relay families, including the T60 Transformer Protection System and the 845 Transformer Protection System. Their available functions, hardware configurations, setting structures, and engineering capabilities depend on the specific model and firmware.

Transformer differential protection compares the currents entering and leaving the protected transformer zone. Under normal operating conditions and for external faults, the relay should remain stable after accounting for transformer ratio, vector group, and CT characteristics. For an internal fault, the difference between the compensated currents becomes significant and the differential element can operate.

This article explains the engineering principles of GE Multilin transformer differential protection, including CT matching, vector-group compensation, differential and restraint currents, inrush restraint, overexcitation considerations, restricted earth-fault protection, settings, testing, and commissioning.

2. What Is Transformer Differential Protection?

Transformer differential protection is based on Kirchhoff’s current law.

For a protected zone, the sum of currents entering and leaving the zone should be approximately zero under healthy operating conditions, provided that all currents are referred to a common basis and their phase relationships are correctly compensated.

A simplified differential-current expression is:

Idiff = |I1′ + I2’|

Where:

  • Idiff is the differential operating current.
  • I1′ is the compensated current from one transformer side.
  • I2′ is the compensated current from the other transformer side.
  • The signs and reference directions depend on the relay’s measurement convention.

For a transformer with multiple windings, the relay may compare compensated currents from several sides.

The relay must account for differences caused by:

  • Transformer voltage ratio.
  • Transformer vector group.
  • CT ratios.
  • CT connections.
  • Phase displacement.
  • Zero-sequence current behavior.
  • Transformer tap-changer position.
  • CT measurement errors.

If these differences are not correctly addressed, the relay may measure a false differential current and operate incorrectly.

3. GE Multilin Transformer Protection Relays

Two important GE Multilin transformer protection products are the T60 and 845.

3.1 GE Multilin T60

The T60 is part of the Universal Relay (UR) family and is designed for transformer protection applications.

Depending on its configuration, the T60 can provide transformer differential protection and additional protection, monitoring, measurement, and programmable logic functions.

Typical engineering applications include:

  • Two-winding transformer protection.
  • Three-winding transformer protection, where supported by the configuration.
  • Differential protection.
  • Transformer overcurrent backup.
  • Restricted earth-fault protection, where available.
  • Thermal and overexcitation-related protection functions, as configured.
  • Transformer monitoring and event analysis.

3.2 GE Multilin 845

The 845 is a transformer protection relay intended for transformer protection and monitoring applications.

Its available protection elements and measurement features depend on the exact model and configuration.

Typical engineering tasks include:

  • Transformer differential protection configuration.
  • CT and transformer data entry.
  • Protection settings and logic engineering.
  • Monitoring transformer operating conditions.
  • Reviewing fault records and event information.
  • Commissioning and functional testing.

3.3 Selecting the Correct Relay

The relay should be selected according to the transformer application, protection philosophy, required functions, CT arrangements, I/O requirements, communications, and project specifications.

Do not assume that every T60 and 845 configuration has identical functionality. Always check the relevant product manual, ordering information, firmware documentation, and application guidance.

4. Transformer Differential Protection Zone

The differential protection zone is defined by the locations of the CTs connected to the relay.

For a two-winding transformer, the zone generally extends between the CTs installed on the high-voltage and low-voltage sides.

<em>Conceptual arrangement:</em>

HV system → HV CT → Transformer → LV CT → LV system

The CTs provide the current measurements used by the differential relay.

For a fault inside this zone, current contributions from the connected sources generally flow toward the fault. The resulting differential current can cause the relay to operate.

For an external fault, the current entering one side of the zone should correspond to the current leaving the other side after compensation. The differential element should remain stable.

4.1 Internal Faults

Examples include:

  • Phase-to-phase winding faults.
  • Phase-to-earth winding faults.
  • Inter-turn faults.
  • Internal lead faults.
  • Faults involving transformer terminals within the protected zone.

The differential protection may detect these faults rapidly, depending on the fault magnitude, location, CT performance, and relay sensitivity.

4.2 External Faults

External faults occur outside the differential protection zone.

Examples include:

  • Faults on the HV busbar.
  • Faults on the LV busbar.
  • Outgoing feeder faults.
  • Faults on connected cables or overhead lines outside the CT boundaries.

During external faults, large through-current may flow through the transformer. The differential relay must remain stable despite CT errors, CT saturation, transformer tap position, and measurement tolerances.

5. Transformer Differential Current and Restraint Current

A modern transformer differential relay generally uses both an operating quantity and a restraining quantity.

5.1 Differential Operating Current

The differential current represents the imbalance between the compensated currents.

For a simplified two-terminal application:

Idiff = |I1′ + I2’|

The relay operates when the differential current satisfies the configured operating characteristic and other required conditions.

5.2 Restraint Current

The restraint quantity provides stability during load current and external faults.

A simplified restraint-current expression is:

Ibias = (|I1’| + |I2’|) / 2

This is an illustrative definition. Actual relays may use different restraint calculations, including alternative definitions and multi-slope characteristics.

5.3 Percentage Differential Characteristic

A percentage differential characteristic increases the required operating current as the restraint current increases.

A simplified single-slope representation is:

Idiff > Imin + Slope × Ibias

Where:

  • Imin is the minimum differential pickup.
  • Slope is the percentage restraint characteristic.
  • Ibias is the restraint current.

In practical numerical relays, the characteristic may contain multiple slopes and additional operating regions.

5.4 Why Is Restraint Required?

Consider a transformer supplying a large load.

The current entering the transformer should correspond to the current leaving it after ratio and phase compensation. However, measurement errors can produce a small differential current.

During a high-current external fault, CT saturation may cause a much larger apparent imbalance.

Without suitable restraint, the relay could incorrectly trip for an external fault.

Percentage differential protection improves stability by considering both differential and through-current quantities.

6. CT Ratio Matching and Transformer Ratio Compensation

Correct CT configuration is one of the most important parts of transformer differential protection engineering.

The currents measured on the transformer HV and LV sides are naturally different because the transformer voltage ratio changes the current magnitude.

The CT ratios must therefore be selected or compensated so that the relay can compare equivalent currents.

6.1 Example: Transformer Current Calculation

Consider a three-phase transformer with the following ratings:

  • Transformer rating: 40 MVA.
  • HV voltage: 132 kV.
  • LV voltage: 33 kV.

The rated line currents are calculated using:

I = S / (√3 × V)

For the HV side:

IHV = 40,000,000 / (√3 × 132,000)

IHV ≈ 175 A

For the LV side:

ILV = 40,000,000 / (√3 × 33,000)

ILV ≈ 700 A

The LV rated current is four times the HV rated current because the voltage ratio is 4:1.

Assume the following CT ratios:

  • HV CT: 200/1 A.
  • LV CT: 800/1 A.

At transformer rated load, the approximate CT secondary currents are:

HV CT secondary current = 175 / 200 = 0.875 A

LV CT secondary current = 700 / 800 = 0.875 A

The two CT secondary current magnitudes are approximately equal at rated transformer load.

This is a simplified example. Actual relay configuration must also account for transformer vector group, phase compensation, current reference direction, CT input characteristics, and the manufacturer’s recommended configuration method.

6.2 CT Selection Considerations

When selecting CTs for transformer differential protection, consider:

  • Primary and secondary current ratings.
  • CT accuracy class.
  • CT knee-point voltage, where relevant.
  • Secondary burden.
  • Lead resistance.
  • Maximum external fault current.
  • CT saturation performance.
  • CT thermal and dynamic ratings.
  • Protection and metering core allocation.

A CT ratio selected only from rated transformer current may not provide adequate performance during severe external faults.

7. Transformer Vector Group Compensation

Transformer vector group compensation is essential for differential protection.

Power transformers may introduce a phase displacement between their HV and LV currents. For example, a transformer with a Dyn11 vector group has a 30-degree displacement between the corresponding winding voltage references, according to the standard vector-group convention.

The differential relay must compensate for the phase displacement before comparing the winding currents.

7.1 Why Is Compensation Necessary?

Consider a transformer with a phase-shifting vector group.

Even when the transformer is operating normally, the HV and LV current phasors are not necessarily aligned.

If the relay compares the currents without appropriate compensation, it may calculate a significant differential quantity under healthy operating conditions.

This can cause unwanted operation.

7.2 Traditional CT Connection Compensation

In older differential protection schemes, CTs were sometimes connected in star or delta arrangements to compensate for transformer phase displacement and zero-sequence effects.

The exact CT connection depended on the transformer vector group and protection design.

7.3 Numerical Relay Compensation

Modern numerical relays can perform phase compensation internally using configured transformer and CT data.

Depending on the relay design, the engineer may enter:

  • Transformer winding voltage ratings.
  • Transformer vector group.
  • CT ratios.
  • Winding connections.
  • Current reference directions.
  • Other application-specific parameters.

The relay then applies the appropriate compensation algorithm.

Do not automatically add external CT delta compensation when the relay is already configured to perform the corresponding compensation internally. Doing so may introduce an additional phase shift and cause incorrect differential measurements.

7.4 Zero-Sequence Compensation

Zero-sequence current behavior is particularly important for transformers with grounded-star windings.

For certain external earth faults, zero-sequence current may flow on one transformer side but not be transferred to the other side in the same manner.

Differential protection must account for this behavior to maintain stability.

The relay’s zero-sequence elimination or compensation method depends on its design and configuration.

8. Transformer Tap-Changer Effects

An on-load tap changer (OLTC) changes the effective transformer turns ratio.

As the tap position changes, the current relationship between the transformer windings also changes.

This can produce a differential current even when the transformer is operating normally.

The percentage differential characteristic is designed to accommodate normal measurement and ratio deviations within the protection design limits.

The engineer should consider:

  • Transformer tap range.
  • Nominal tap position.
  • Maximum and minimum operating tap positions.
  • CT ratio selection.
  • Relay ratio compensation.
  • Differential pickup and restraint settings.

If the relay supports tap-position information or adaptive compensation, its use must follow the manufacturer’s application guidance.

9. Magnetizing Inrush and Differential Protection Stability

Transformer energization can produce a high magnetizing inrush current.

This current is not necessarily associated with an internal fault. It is caused by the transient magnetic condition of the transformer core during energization.

If the differential relay interprets the inrush current as an internal fault, it may trip the transformer unnecessarily.

9.1 Causes of Magnetizing Inrush

Inrush current depends on several factors, including:

  • Switching instant on the voltage waveform.
  • Residual flux in the transformer core.
  • Transformer core characteristics.
  • Source impedance.
  • Transformer design.
  • Energization arrangement.
  • Point-on-wave switching conditions.

Inrush current can be significantly higher than normal rated current and may contain a substantial harmonic component.

9.2 Second-Harmonic Restraint

A traditional method of distinguishing magnetizing inrush from internal faults is second-harmonic restraint.

Magnetizing inrush current often contains a significant second-harmonic component.

The relay evaluates the harmonic content of the differential current and may restrain or supervise differential operation when the configured inrush criteria are satisfied.

9.3 Inrush Detection and Blocking

Depending on the relay design, inrush detection may be implemented through:

  • Harmonic restraint.
  • Harmonic blocking.
  • Other waveform-based or transient detection methods.
  • Cross-phase blocking or related logic, where supported.

The exact method and available settings must be checked in the selected GE Multilin relay manual.

9.4 Engineering Considerations

Second-harmonic restraint settings must balance security and dependability.

If the threshold is too low, the relay may fail to restrain correctly during inrush.

If the threshold is too high, the relay may become excessively restrained under certain internal fault conditions.

Modern transformer protection designs must also consider that some internal faults can contain harmonic components and that some inrush waveforms may not exhibit a simple, consistent harmonic signature.

The manufacturer’s recommended application settings and testing guidance should be followed.

10. Overexcitation and the Fifth Harmonic

Transformer overexcitation occurs when the magnetic flux in the transformer core exceeds its intended operating level.

A simplified relationship is:

Flux ∝ V / f

Where:

  • V is applied voltage.
  • f is supply frequency.

An increase in voltage or a reduction in frequency can increase the magnetic flux density.

Overexcitation can cause:

  • Core saturation.
  • Increased magnetizing current.
  • Excessive heating.
  • Increased vibration and noise.
  • Insulation deterioration.

The fifth-harmonic component may be used in some transformer differential protection designs as part of overexcitation supervision or restraint.

However, fifth-harmonic restraint is not a substitute for a dedicated volts-per-hertz protection function where that function is required.

The protection engineer should review the relay’s available overexcitation protection, differential restraint logic, and application recommendations.

11. Restricted Earth-Fault Protection (ANSI 64REF)

Restricted earth-fault protection is a sensitive earth-fault protection method used for a defined transformer winding zone.

It is often applied to grounded-star transformer windings.

REF protection compares the residual current from the phase CTs with the current measured by the neutral CT.

For a simplified arrangement:

IREF = IA + IB + IC + IN

The signs and polarity conventions depend on the CT arrangement and relay measurement reference.

Under normal conditions and for external earth faults, the relevant currents should balance according to the protection-zone design.

For an internal earth fault within the REF zone, an imbalance develops and the relay can operate.

11.1 High-Impedance and Low-Impedance REF

Two broad REF protection approaches are used in transformer protection schemes:

High-impedance REF

This approach uses a high-impedance operating circuit and requires carefully matched CT characteristics and appropriate stabilizing components.

Low-impedance REF

This approach uses numerical measurement and a configured differential or restricted earth-fault characteristic.

The available REF implementation must be confirmed for the selected GE Multilin relay.

11.2 REF Protection Zone

The REF zone is defined by the phase CTs and neutral CT arrangement.

It typically protects the grounded winding section between these CT locations.

REF can provide greater sensitivity to certain winding earth faults than transformer phase differential protection alone.

However, REF does not replace overall transformer differential protection. The two functions provide complementary protection coverage.

12. Transformer Differential Protection Settings

Transformer differential settings must be calculated from the transformer data, CT characteristics, network fault levels, and protection philosophy.

Typical setting considerations include:

12.1 Minimum Differential Pickup

The minimum differential pickup determines the operating threshold at low restraint current.

It must be high enough to avoid operation due to normal measurement errors and transformer operating conditions, but sufficiently sensitive to detect internal faults.

12.2 Differential Restraint Slopes

The percentage restraint characteristic improves stability during through-faults and CT saturation.

The engineer should consider:

  • CT accuracy.
  • CT saturation performance.
  • Maximum external fault current.
  • Transformer tap range.
  • Measurement errors.
  • Relay operating characteristic.

12.3 High-Set Differential Element

Some transformer differential protection designs provide an additional high-set differential element.

This element may operate without the same percentage restraint characteristic used by the biased differential element.

Its setting must be selected carefully to maintain security for external faults and inrush conditions, according to the relay’s implementation.

12.4 Inrush Restraint Settings

Where supported, inrush restraint settings determine how the relay identifies and responds to magnetizing inrush.

The settings should be based on the manufacturer’s guidance and the transformer application.

12.5 REF Settings

Where REF protection is available, the engineer must calculate and verify:

  • Operating pickup.
  • Restraint or stability characteristic.
  • CT ratio compatibility.
  • Neutral CT polarity.
  • Protected zone boundaries.
  • Trip logic.

13. Practical Transformer Differential Example

Consider a 40 MVA, 132/33 kV transformer with the following assumed data:

  • HV rated current: approximately 175 A.
  • LV rated current: approximately 700 A.
  • HV CT ratio: 200/1 A.
  • LV CT ratio: 800/1 A.
  • Transformer vector group: Dyn11.

At rated load:

HV CT secondary current ≈ 0.875 A

LV CT secondary current ≈ 0.875 A

The CT secondary current magnitudes are approximately equal.

However, the relay must still compensate for the transformer vector-group phase displacement and apply the correct current reference directions.

The engineering process is therefore:

  1. Enter the transformer rated power and winding voltages.
  2. Configure the transformer vector group correctly.
  3. Enter the HV and LV CT ratios.
  4. Confirm the CT polarity and current reference directions.
  5. Configure the relay’s differential measurement and compensation.
  6. Verify the compensated current values under balanced load conditions.
  7. Check the differential and restraint measurements.
  8. Configure the differential characteristic.
  9. Configure inrush and other applicable supervision.
  10. Test internal and external fault operating conditions.

This example illustrates the configuration principles only. Final protection settings must be calculated and verified using the actual transformer nameplate, CT data, relay manual, and system study.

14. GE Multilin EnerVista Configuration Workflow

EnerVista software is used for engineering selected GE Multilin relay models. The exact software version and available settings depend on the relay family and firmware.

A general transformer differential engineering workflow includes the following steps.

Step 1 – Create or Open the Relay Project

Identify the exact relay model and firmware.

Create the project using the appropriate EnerVista application and establish communication with the relay where required.

Step 2 – Enter Transformer Data

Configure the available transformer information, including:

  • Transformer rating.
  • Winding voltages.
  • Winding configuration.
  • Vector group.
  • Number of windings.
  • Relevant application parameters.

Step 3 – Configure CT Inputs

Enter the CT ratios and verify the measurement assignments for each transformer side.

Confirm that the selected current inputs correspond to the physical wiring drawings.

Step 4 – Configure Differential Protection

Review the available differential protection settings, including:

  • Differential pickup.
  • Restraint characteristic.
  • Slope settings.
  • High-set differential settings, where available.
  • Inrush restraint or blocking.
  • Relevant supervision and logic.

Step 5 – Configure Additional Transformer Protection

Depending on the relay and project requirements, configure additional functions such as:

  • Overcurrent backup.
  • Earth-fault protection.
  • REF protection, where available.
  • Thermal protection.
  • Overexcitation protection.
  • Breaker failure initiation.
  • Trip and alarm logic.

Step 6 – Review Logic and Outputs

Confirm that the intended protection elements operate the correct trip outputs.

Check breaker trip circuits, lockout relay interfaces, alarms, and any required interlocking.

Step 7 – Save and Document the Settings

Save the approved configuration and maintain a controlled settings revision.

Record the relay model, firmware, project revision, settings file, and commissioning test results.

15. Testing GE Multilin Transformer Differential Protection

Transformer differential protection requires comprehensive testing.

The commissioning engineer should verify not only individual element pickup but also the overall differential measurement and stability characteristics.

15.1 Secondary Injection Test Equipment

A suitable relay test set should provide the required current channels and phase-angle control.

For more advanced tests, the test equipment should support simultaneous multi-phase injection and the necessary waveform or harmonic injection capabilities.

The number of channels and test method depend on the relay configuration and test objective.

15.2 CT Ratio and Current Measurement Test

Verify that the relay measures the expected current magnitudes.

Procedure:

  1. Inject current into the relevant relay inputs.
  2. Compare measured current with the expected secondary value.
  3. Verify phase identification.
  4. Check current polarity.
  5. Confirm CT ratio scaling.
  6. Record the results.

15.3 Vector Group Compensation Test

The purpose is to confirm that the relay correctly compensates for transformer phase displacement.

Procedure:

  1. Confirm the configured transformer vector group.
  2. Apply the required current signals to the transformer-side inputs.
  3. Use phase relationships representing normal transformer operation.
  4. Review the relay’s compensated current quantities.
  5. Confirm that the differential current remains within the expected stable region.

A test should use the manufacturer’s recommended injection method. Do not assume that simply injecting identical in-phase currents into all relay inputs represents normal operation for a phase-shifting transformer.

15.4 Differential Pickup Test

The purpose is to verify the operating threshold.

Procedure:

  1. Establish the required restraint conditions.
  2. Inject differential current into the relay.
  3. Increase the differential current gradually.
  4. Record the pickup value.
  5. Compare the result with the configured setting and tolerance.

15.5 Bias Characteristic Test

The purpose is to verify the differential relay’s restraint characteristic.

Procedure:

  1. Apply the required current signals to establish a selected restraint current.
  2. Introduce an imbalance between the compensated currents.
  3. Increase the differential component gradually.
  4. Record the operating point.
  5. Repeat at different restraint-current levels.
  6. Compare the results with the configured characteristic.

The test report should include the relevant restraint-current values and differential operating thresholds.

15.6 External Fault Stability Test

An external fault produces high through-current through the protected transformer zone.

The relay should remain stable when the injected current quantities represent an external fault and the CT measurement conditions remain within the intended stability design.

The test engineer should verify that the differential element does not operate for the defined external-fault test conditions.

CT saturation performance requires additional consideration and may require dedicated testing or engineering assessment.

15.7 Inrush Restraint Test

Where supported by the relay and test equipment, a waveform containing the required harmonic content can be injected to verify inrush restraint behavior.

The engineer should confirm:

  • Inrush detection.
  • Harmonic measurement.
  • Restraint or blocking behavior.
  • Differential trip supervision.
  • Relevant status indications.

The test waveform and acceptance criteria must follow the manufacturer’s test guidance.

15.8 REF Protection Test

For REF protection, verify the phase CT and neutral CT measurement relationship.

Test both:

  • External earth-fault stability.
  • Internal earth-fault operating conditions.

The test must reproduce the correct current directions and magnitudes for the configured REF arrangement.

15.9 Trip Circuit Test

Finally, verify the complete trip chain:

Protection element → Relay logic → Output contact → Trip circuit → Circuit breaker trip coil

Confirm that alarms, lockout logic, and breaker failure initiation operate as specified by the project design.

16. Common Transformer Differential Protection Problems

Problem 1 – Differential Current Is High During Normal Load

Possible causes:

  • Incorrect CT ratio.
  • Incorrect transformer vector group.
  • Incorrect CT polarity.
  • Incorrect phase assignment.
  • Incorrect winding configuration.
  • Incorrect zero-sequence compensation.
  • Incorrect transformer data.

Recommended action: Verify the transformer and CT configuration before changing the differential pickup.

Problem 2 – Relay Trips During Transformer Energization

Possible causes:

  • Inrush restraint not correctly configured.
  • Incorrect harmonic settings.
  • Incorrect current measurement configuration.
  • Inrush detection or blocking logic not operating as intended.
  • Incorrect transformer application settings.

Recommended action: Review the event record and oscillography, then verify the inrush restraint configuration and test results.

Problem 3 – Relay Trips During External Faults

Possible causes:

  • CT saturation.
  • Incorrect CT polarity.
  • Incorrect CT ratio.
  • Insufficient restraint.
  • Incorrect differential characteristic.
  • Incorrect phase compensation.

Recommended action: Review the external fault current, CT performance, and differential operating quantities.

Problem 4 – Differential Protection Does Not Detect an Internal Fault

Possible causes:

  • Incorrect differential pickup.
  • Incorrect CT connections.
  • Incorrect current input assignment.
  • Incorrect relay logic.
  • Inadequate sensitivity for the particular fault.
  • Fault current below the operating threshold.

Recommended action: Verify the complete protection configuration and assess the fault type and location against the protection-zone coverage.

Problem 5 – REF Protection Does Not Operate Correctly

Possible causes:

  • Incorrect neutral CT polarity.
  • Incorrect phase CT residual connection.
  • Incorrect REF zone configuration.
  • Incorrect pickup or restraint settings.
  • Incorrect trip logic.

Recommended action: Test the phase and neutral CT circuits independently and then verify the complete REF measurement arrangement.

17. Practical Commissioning Checklist

Before energizing a transformer protected by a GE Multilin differential relay, check the following:

  • Correct relay model and firmware confirmed.
  • Transformer nameplate data verified.
  • Transformer voltage and power ratings entered correctly.
  • Transformer vector group verified.
  • HV and LV CT ratios checked.
  • CT polarity and phase assignment verified.
  • VT configuration checked, where required.
  • Differential compensation verified.
  • Zero-sequence compensation reviewed.
  • Minimum differential pickup checked.
  • Bias slopes and restraint characteristic checked.
  • High-set differential function checked, where available.
  • Inrush restraint or blocking tested, where available.
  • Overexcitation protection reviewed.
  • REF configuration and CT circuits checked, where applicable.
  • External fault stability tested.
  • Internal fault operation tested.
  • Trip logic and output contacts tested.
  • Circuit breaker trip circuit verified.
  • Event records and oscillography checked.
  • Final settings and test reports archived.

18. Engineering Recommendations

Transformer differential protection requires a combination of correct design, accurate instrument-transformer data, appropriate relay settings, and comprehensive testing.

Important recommendations include:

  1. Always use the transformer nameplate and approved design documents as the basis for configuration.
  2. Verify CT polarity before performing differential tests.
  3. Confirm that vector-group compensation is implemented correctly.
  4. Avoid applying external CT compensation when the numerical relay already performs the same compensation internally.
  5. Check CT saturation performance for maximum external fault conditions.
  6. Consider the complete transformer tap range.
  7. Review inrush restraint settings against the manufacturer’s recommendations.
  8. Treat overexcitation protection as a separate engineering consideration.
  9. Use REF protection where required to improve sensitivity for suitable grounded-winding applications.
  10. Verify differential stability under normal load and external fault conditions.
  11. Test the complete trip chain.
  12. Maintain controlled settings files and commissioning records.

19. Conclusion

GE Multilin transformer differential protection provides an important method of detecting internal transformer faults while maintaining stability during normal operation and external faults.

The T60 and 845 are examples of GE Multilin transformer protection solutions. Their exact protection functions and configuration options must be checked against the applicable model documentation.

Successful transformer differential protection engineering depends on several interconnected tasks: CT ratio matching, vector-group compensation, differential and restraint characteristic selection, inrush restraint, zero-sequence treatment, and appropriate REF protection.

For commissioning engineers, one of the most important objectives is to demonstrate that the relay measures balanced compensated currents under normal operating conditions, remains stable for external faults, and operates correctly for simulated internal faults.

20. Training on GE Multilin Transformer Protection by Elec-Engg

Elec-Engg provides practical technical training by Dr Saeed Roostaee (Electrical Engineering) for engineers involved in power system protection, transformer protection, relay configuration, testing, and commissioning.

Relevant training topics include:

  • GE Multilin T60 and 845 transformer protection engineering.
  • Transformer differential protection (ANSI 87T).
  • CT ratio selection and CT polarity verification.
  • Transformer vector-group compensation.
  • Differential and bias characteristic settings.
  • Magnetizing inrush and harmonic restraint.
  • Transformer REF protection.
  • Transformer overcurrent and backup protection.
  • EnerVista configuration and settings management.
  • Secondary injection testing and commissioning.
  • Fault records, oscillography, and troubleshooting.

Training is available through pre-recorded video courses, structured self-paced programs, live online sessions, face-to-face courses, and customized in-house training.

Visit https://elec-engg.com/ to explore available technical training programs or contact Elec-Engg through https://elec-engg.com/contact/ for customized training requirements.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top