The SEL-321 Phase and Ground Distance Relay from Schweitzer Engineering Laboratories (SEL) is a microprocessor-based transmission-line protection relay designed for high-voltage (HV), extra-high-voltage (EHV), and subtransmission systems.
The SEL-321 provides comprehensive phase and ground distance protection, directional overcurrent protection, communications-assisted tripping, single-pole and three-pole tripping logic, power-swing protection, load encroachment detection, and fault location.
It was designed to protect overhead transmission lines in both pilot and non-pilot protection schemes. Its flexible logic, multiple settings groups, and configurable protection elements made it a versatile solution for transmission-line protection.
Although the SEL-321 is no longer in production, it remains relevant to protection engineers responsible for maintaining, testing, troubleshooting, and upgrading existing installations.
This technical guide explains the SEL-321 relay’s protection functions, distance characteristics, communication schemes, settings, configuration, and practical commissioning procedures.
SEL-321 Protection Relay: Complete Guide to Distance Protection, Applications, Settings and Testing
- 1. What is the SEL-321 relay?
- 2. Applications of the SEL-321 relay
- 3. SEL-321 protection functions and ANSI codes
- 4. Distance protection principle of the SEL-321
- 5. Four-zone phase and ground distance protection
- 6. Mho distance protection characteristics
- 7. Ground distance protection – Mho and quadrilateral characteristics
- 8. Directional protection and negative-sequence directional elements
- 9. Directional overcurrent protection
- 10. Communications-assisted protection schemes
- 11. Weak-infeed logic
- 12. Single-pole tripping and open-pole protection
- 13. Power-swing blocking and out-of-step protection
- 14. Load encroachment protection
- 15. Time-overcurrent backup protection
- 16. Fault locator and event recording
- 17. SELogic control equations and multiple settings groups
- 18. SEL-321-5: Special considerations for 50 Hz systems
- 19. SEL-321 settings and configuration
- 20. SEL-321 testing and commissioning
- 20.1 Visual inspection
- 20.2 Auxiliary supply test
- 20.3 CT and VT circuit testing
- 20.4 Distance protection testing
- 20.5 Directional element testing
- 20.6 Overcurrent testing
- 20.7 Communication scheme testing
- 20.8 Single-pole tripping tests
- 20.9 Power-swing and load-encroachment tests
- 20.10 Event report analysis
- 21. Software used with the SEL-321
- 22. SEL-321 versus SEL-311C
- 23. SEL-321 product status and replacement considerations
- 24. Advantages of the SEL-321
- 25. Frequently asked questions about the SEL-321
- 26. Practical protection relay training by Elec-Engg
1. What is the SEL-321 relay?
The SEL-321 is a phase and ground distance protection relay designed for transmission-line applications.
Its principal protection functions include:
- Four zones of phase distance protection.
- Four zones of ground distance protection.
- Phase mho distance characteristics.
- Ground mho and quadrilateral distance characteristics.
- Directional overcurrent protection.
- Negative-sequence and residual overcurrent protection.
- Power-swing blocking and out-of-step tripping.
- Load encroachment detection.
- Communications-assisted tripping.
- Single-pole and three-pole tripping.
- Automatic fault location.
- Oscillographic event recording.
- Programmable SELogic control equations.
The relay supports a variety of protection schemes, including POTT, PUTT, DCB, DCUB, DUTT, and DTT.
It can also be configured for applications involving series-compensated transmission lines, subject to the particular relay model and protection design.
Important: The SEL-321 is a discontinued product. This article is intended for technical understanding and maintenance of existing installations, not as a recommendation for new procurement.
2. Applications of the SEL-321 relay
2.1 High-voltage transmission-line protection
The primary application of the SEL-321 is protection of overhead transmission lines.
A typical installation includes:
- Three-phase current transformer inputs.
- Three-phase voltage transformer inputs.
- Circuit breaker trip circuits.
- DC auxiliary supply.
- Protection communication equipment, when a pilot scheme is used.
- Alarm and control circuits.
The relay measures the electrical quantities at the substation and calculates the apparent impedance seen from the relay location.
When the measured impedance enters a configured distance protection zone, the corresponding protection element operates according to its directional and timing logic.
2.2 Extra-high-voltage transmission lines
The SEL-321 was designed for EHV, HV, and subtransmission applications.
Its four-zone distance protection and communications-assisted tripping logic make it suitable for transmission-line protection schemes requiring fast primary protection and coordinated backup protection.
2.3 Subtransmission-line protection
For subtransmission networks, the SEL-321 can provide:
- Primary distance protection.
- Time-delayed backup protection.
- Directional overcurrent protection.
- Ground-fault protection.
- Fault location.
- Communication-assisted tripping.
The actual protection scheme depends on the network topology, source impedance, line parameters, and protection coordination requirements.
2.4 Single-pole tripping applications
The SEL-321 supports single-pole and three-pole tripping applications.
Single-pole tripping is particularly useful on important transmission lines where a single-phase-to-ground fault can be cleared by opening only the faulted phase.
The relay includes phase selection, open-pole interval protection, and phase-discordance logic.
These functions help manage the special conditions associated with single-pole-open operation.
2.5 Replacement of electromechanical distance relays
One of the historical applications of the SEL-321 was replacing older electromechanical distance protection systems.
The relay provides programmable logic, multiple settings groups, event reports, metering, and fault location in a compact digital protection platform.
Its mounting options were also designed to facilitate retrofits in existing protection panels.
3. SEL-321 protection functions and ANSI codes
The following table summarizes the principal protection functions.
| ANSI code | Protection function | Application |
|---|---|---|
| 21P | Phase distance protection | Phase-to-phase and three-phase faults |
| 21G | Ground distance protection | Phase-to-ground faults |
| 50P | Instantaneous phase overcurrent | High-current phase faults |
| 51P | Time-delayed phase overcurrent | Backup phase protection |
| 50N / 50G | Instantaneous residual overcurrent | Ground-fault detection |
| 51N / 51G | Time-delayed residual overcurrent | Ground-fault backup |
| 50Q / 51Q | Negative-sequence overcurrent | Unbalanced fault protection |
| 67 | Directional overcurrent | Directional fault detection |
| 68 | Power-swing blocking | Security during power swings |
| 78 | Out-of-step protection | Power-system stability protection |
| 27 | Undervoltage | Voltage supervision |
| 59 | Overvoltage | Voltage supervision |
| 85 | Pilot protection / transfer-trip scheme | Communication-assisted protection |
| 74 | Alarm function | Relay and protection alarms |
ANSI numbers are commonly used to describe these protection functions. The exact available elements and logic depend on the relay version and configured scheme.
4. Distance protection principle of the SEL-321
Distance protection is based on measuring the apparent impedance between the relay location and the fault.
The basic impedance equation is:
[
Z_{\mathrm{app}}=\frac{V}{I}
]
Where:
- (Z_{\mathrm{app}}) is the apparent impedance measured by the relay.
- (V) is the measured voltage.
- (I) is the measured current.
When a fault occurs on a transmission line, the measured impedance generally decreases.
The relay compares the measured impedance with its configured protection zones.
If the impedance enters a forward-looking protection zone and the required supervision conditions are satisfied, the relay can initiate a trip.
The SEL-321 uses mho characteristics for phase distance protection and provides mho and quadrilateral characteristics for ground distance protection.
5. Four-zone phase and ground distance protection
The SEL-321 provides four zones of phase and ground distance protection.
The zones can be configured independently, with individual directional selections and time delays.
5.1 Zone 1 – Instantaneous distance protection
Zone 1 is generally applied for high-speed protection of a selected portion of the protected transmission line.
Typical engineering considerations include:
- Line impedance.
- CT and VT accuracy.
- Measurement errors.
- Fault resistance.
- Remote infeed.
- Transient overreach.
- Coordination with adjacent protection.
The actual reach must be calculated from the protected line parameters and the network study.
5.2 Zone 2 – Time-delayed distance protection
Zone 2 is generally extended beyond the protected line to provide backup protection for part of the adjacent system.
Its operating time must coordinate with the protection at the remote substation.
5.3 Zone 3 – Remote backup protection
Zone 3 can provide extended backup protection.
Depending on the application, it may be configured in the forward or reverse direction.
5.4 Zone 4 – Additional protection zone
Zone 4 provides an additional independently configured distance zone.
It can be used for extended backup or reverse-looking protection, depending on the protection philosophy.
Engineering note: These are typical distance-protection applications, not mandatory SEL-321 zone assignments. The relay allows the zones to be configured and timed according to the specific protection study.
<AsyncImage query=”transmission line distance protection relay four zone impedance R X diagram mho circles” aspectRatio=”16:9″ width=”100%”/>
6. Mho distance protection characteristics
The SEL-321 uses mho characteristics for phase distance protection.
The mho characteristic is widely used in transmission-line protection because it provides directional behavior and is suitable for long transmission lines.
The relay uses positive-sequence memory voltage polarization to improve security during close-in faults.
6.1 Phase mho elements
Phase mho elements are used to detect:
- Phase-to-phase faults.
- Three-phase faults.
The relay provides four phase distance zones.
Each zone can be configured with the appropriate reach and timing.
6.2 Memory voltage polarization
During a close-in three-phase fault, the measured voltage may collapse significantly.
This can make directional determination difficult if the relay relies only on the instantaneous voltage.
The SEL-321 uses positive-sequence memory voltage polarization to maintain directional security during such conditions.
This is particularly important for close-in faults and weak-source applications.
7. Ground distance protection – Mho and quadrilateral characteristics
Ground distance protection is used for phase-to-ground faults.
Ground faults are more complicated than phase faults because the measured impedance is affected by zero-sequence impedance and ground-return paths.
The SEL-321 includes both ground mho and ground quadrilateral distance characteristics.
7.1 Ground mho distance protection
Ground mho elements provide directional distance protection for phase-to-ground faults.
The relay uses zero-sequence compensation factors to account for the difference between positive-sequence and zero-sequence line impedance.
The compensation factors are commonly represented as (k_0) and (k_{01}).
Correct calculation of these factors is essential for accurate ground distance measurement.
7.2 Ground quadrilateral distance protection
Quadrilateral distance characteristics provide additional resistive fault coverage.
This can be particularly useful when detecting high-resistance ground faults.
The quadrilateral characteristic allows engineers to define separate resistive and reactive reaches.
The SEL-321 supports four zones of ground quadrilateral distance protection, in addition to its ground mho elements.
7.3 Mho versus quadrilateral distance protection
| Characteristic | Mho | Quadrilateral |
|---|---|---|
| Main advantage | Directional characteristic | Adjustable resistive reach |
| Application | Transmission-line distance protection | Ground faults with higher fault resistance |
| Directionality | Inherent characteristic | Requires appropriate directional supervision |
| Resistive coverage | More limited | More flexible |
| Engineering concern | Underreach and load encroachment | Load overlap and resistive reach |
<AsyncImage query=”mho and quadrilateral ground distance protection relay R X characteristic comparison technical diagram” aspectRatio=”16:9″ width=”100%”/>
8. Directional protection and negative-sequence directional elements
The SEL-321 includes two independent negative-sequence directional elements.
Negative-sequence quantities are particularly useful for determining fault direction during unbalanced faults.
The directional elements help supervise ground and negative-sequence overcurrent functions and improve the security of communications-assisted protection schemes.
For ground distance protection, correct directional supervision is especially important during:
- Single-phase-to-ground faults.
- Double-phase-to-ground faults.
- Faults involving remote infeed.
- Parallel-line current reversal conditions.
- Weak-source conditions.
The SEL-321 also uses positive-sequence memory voltage polarization for directional security during three-phase faults.
9. Directional overcurrent protection
The SEL-321 provides phase, negative-sequence, and residual overcurrent protection.
These functions can be used as primary or backup protection, depending on the system design.
9.1 Phase overcurrent protection
Phase overcurrent elements detect excessive phase current.
They can provide backup protection for phase faults when distance protection does not operate or is unavailable.
9.2 Negative-sequence overcurrent protection
Negative-sequence current is generated by unbalanced system conditions.
The negative-sequence overcurrent elements can detect:
- Phase-to-phase faults.
- Unbalanced phase faults.
- Certain ground faults.
- Abnormal unbalanced operating conditions.
9.3 Residual overcurrent protection
Residual current is used to detect ground faults.
The SEL-321 provides multiple levels of instantaneous and definite-time negative-sequence and residual overcurrent protection.
The elements can be coordinated with distance protection and used in communication-assisted logic.
10. Communications-assisted protection schemes
One of the important capabilities of the SEL-321 is its support for communications-assisted tripping.
These schemes use information exchanged between the two line terminals to accelerate fault clearance.
The relay supports:
- POTT – Permissive Overreaching Transfer Trip.
- PUTT – Permissive Underreaching Transfer Trip.
- DCB – Directional Comparison Blocking.
- DCUB – Directional Comparison Unblocking.
- DUTT – Direct Underreaching Transfer Trip.
- DTT – Direct Transfer Trip.
10.1 POTT – Permissive Overreaching Transfer Trip
In a POTT scheme, an overreaching directional distance element detects a forward fault and sends a permissive signal to the remote terminal.
The local relay trips when its own forward protection element operates and the required permissive signal is received.
This allows high-speed tripping for internal line faults.
10.2 PUTT – Permissive Underreaching Transfer Trip
In a PUTT scheme, a local underreaching distance element initiates a permissive signal.
The remote terminal uses the received signal together with its own protection logic to determine whether tripping is permitted.
10.3 DCB – Directional Comparison Blocking
In DCB protection, the relays exchange blocking signals to prevent unwanted tripping for external faults.
A forward-looking fault detection element can initiate tripping unless a blocking signal is received from the remote terminal.
10.4 DCUB – Directional Comparison Unblocking
Directional comparison unblocking uses a communication channel to provide a permissive unblocking condition.
The protection logic is designed to maintain security when the communication channel is unavailable or interrupted.
10.5 DTT – Direct Transfer Trip
Direct transfer trip sends a trip command to a remote terminal.
It is commonly used for special protection and intertripping applications.
10.6 Mirrored Bits communication
The SEL-321 supports SEL’s Mirrored Bits technology.
Mirrored Bits allows relay logic information to be exchanged between devices through supported communications equipment.
It can be used for:
- Permissive signals.
- Blocking signals.
- Direct transfer-trip commands.
- Remote logic.
- Protection coordination.
Communication channel configuration and scheme logic must be carefully tested before placing the protection system into service.
11. Weak-infeed logic
Weak-infeed conditions occur when one terminal of a transmission line has a relatively weak source.
For an internal fault near the weak terminal, the local relay may not measure sufficient current to operate its normal distance elements.
The SEL-321 includes weak-infeed logic to support rapid clearing at both line terminals for suitable internal-fault conditions.
This logic can be particularly important in networks with:
- Weak generation sources.
- Long transmission lines.
- Renewable generation connections.
- Remote substations.
- Different source-strength conditions at the two line terminals.
The protection engineer must ensure that the permissive and weak-infeed logic is coordinated with the communication scheme and local voltage/current supervision.
12. Single-pole tripping and open-pole protection
The SEL-321 supports both single-pole and three-pole tripping.
Single-pole tripping is frequently used on important transmission lines to improve system stability during single-phase-to-ground faults.
12.1 Faulted-phase selection
The relay includes phase-selection logic to identify the faulted phase.
Correct phase identification is essential because only the faulted pole should be opened during single-pole tripping.
12.2 Open-pole interval protection
After a single-pole trip, the transmission line operates temporarily with one phase open.
This condition creates an unbalanced system.
The relay includes open-pole interval protection logic to handle the special conditions associated with this operating state.
12.3 Phase discordance
Phase-discordance logic detects situations where the circuit breaker poles are not in the expected operating condition.
The relay can use this information to initiate three-pole tripping when required by the protection scheme.
12.4 Single-pole-open power-swing protection
Power-swing protection must consider the special conditions that occur during the single-pole-open interval.
The SEL-321-5 has specific power-swing blocking provisions during the single-pole-open period immediately following a single-pole trip.
13. Power-swing blocking and out-of-step protection
Power swings occur when generators and interconnected power systems experience changes in rotor-angle stability.
During a stable power swing, the apparent impedance measured by a distance relay may enter a distance protection characteristic.
Without suitable supervision, this could result in an unwanted trip.
The SEL-321 provides out-of-step elements for power-swing blocking and tripping.
13.1 Power-swing blocking
Power-swing blocking logic helps prevent distance protection from operating incorrectly during stable power swings.
13.2 Out-of-step tripping
For an unstable power swing, the system may require controlled separation.
The relay includes out-of-step tripping functions to support the configured protection strategy.
The settings must be coordinated with the system stability study and the utility’s power-swing protection philosophy.
14. Load encroachment protection
High power transfer can cause the apparent impedance seen by a distance relay to enter its protection characteristic.
This can result in an unwanted operation if the distance protection is not properly supervised.
The SEL-321 includes load encroachment logic to prevent operation of three-phase distance elements under high-load conditions.
The engineer defines a load region in the impedance plane.
When the apparent impedance enters the defined load region, the appropriate three-phase distance elements are prevented from operating according to the configured logic.
This feature is particularly important for:
- Long transmission lines.
- Heavily loaded transmission corridors.
- Systems operating close to their thermal limits.
- Networks with large power-transfer variations.
15. Time-overcurrent backup protection
The SEL-321 includes independent phase, negative-sequence, and residual time-overcurrent elements.
These elements can provide backup protection for faults on the protected line and remote terminals.
They may also be supervised by distance or directional elements to improve selectivity.
Protection engineers should calculate the required pickup and time delays based on:
- Maximum load current.
- Minimum fault current.
- Maximum and minimum source strength.
- CT ratios.
- Adjacent relay coordination.
- Fault-clearing requirements.
16. Fault locator and event recording
The SEL-321 provides a built-in fault locator.
This feature calculates an estimated fault location using the electrical measurements recorded during the fault.
The information helps maintenance personnel identify the likely fault location and reduce line-inspection time.
The relay also provides event reports and oscillographic information.
According to the SEL data sheet, the standard event report includes:
- Eleven cycles of event information.
- Four cycles of prefault data.
- Seven cycles of postfault data.
- Voltage measurements.
- Current measurements.
- Protection element status.
- Input and output contact status.
- Calculated fault location.
- Date and time of the event.
The SEL-321 stores the last 12 event reports for local or remote retrieval.
The SEL-321-2 version offers extra-long event reports, as identified in the manufacturer’s product information.
17. SELogic control equations and multiple settings groups
The SEL-321 includes programmable SELogic control equations.
These equations allow protection engineers to combine relay elements and external input signals to create application-specific protection and control logic.
Typical applications include:
- Breaker trip logic.
- Breaker close logic.
- Communication scheme logic.
- Blocking and permissive logic.
- Alarm generation.
- External interlocking.
- Remote control functions.
- Single-pole trip logic.
The relay also supports six independent settings groups.
Multiple settings groups can be useful when system configurations change or when a substitute line protection arrangement is required.
For example, different settings groups may be selected to accommodate different network configurations or source conditions.
18. SEL-321-5: Special considerations for 50 Hz systems
The SEL-321-5 is a particular version of the SEL-321 family designed for 50 Hz EHV and HV applications.
SEL describes the SEL-321-5 as being designed to meet stringent single-pole tripping requirements.
Its product information highlights:
- Four zones of phase and ground distance protection.
- Mho and/or quadrilateral ground distance characteristics.
- Adaptive directional element.
- Negative- and zero-sequence directional measurements.
- Independent phase and ground distance timers.
- Mirrored Bits communications.
- Eight independent Mirrored Bits channels per relay.
- Three independent serial communication ports.
- Flexible RTU and communication functions.
- Power-swing blocking during the single-pole-open period.
The adaptive directional element selects between negative- and zero-sequence quantities according to signals generated by the disturbance.
Important: The SEL-321-5 should not be treated as identical to every other SEL-321 variant. Always check the exact model, instruction manual and firmware information before modifying an existing installation.
19. SEL-321 settings and configuration
The SEL-321 can be configured using acSELerator QuickSet SEL-5030.
The settings process should begin with a detailed protection study rather than copying settings from another line.
19.1 Transmission-line data
Collect the following information:
- Line voltage.
- Positive-sequence resistance.
- Positive-sequence reactance.
- Zero-sequence resistance.
- Zero-sequence reactance.
- Line length.
- CT ratio.
- VT ratio.
- Maximum load current.
- Maximum and minimum short-circuit levels.
19.2 CT and VT configuration
Verify the CT and VT ratios and secondary ratings.
Incorrect CT or VT ratios will affect the impedance measured by the relay.
Check the phase connections, polarity and wiring before calculating distance settings.
19.3 Phase distance settings
Calculate the phase distance reach for the required protection zones.
Consider:
- Zone 1 reach.
- Zone 2 reach and coordination time.
- Zone 3 reach.
- Zone 4 reach and direction.
- Line angle.
- Source impedance.
- Adjacent line protection.
- Remote infeed and outfeed.
19.4 Ground distance settings
Ground distance settings require additional attention because of zero-sequence compensation.
Calculate the appropriate compensation factors using the line sequence impedances.
Check the selected ground mho or quadrilateral characteristic.
19.5 Directional overcurrent settings
Calculate phase, negative-sequence and residual overcurrent pickup values.
Coordinate the time delays with adjacent protection systems.
19.6 Communication-assisted protection settings
For a POTT, PUTT, DCB, DCUB, DUTT or DTT scheme, verify:
- Communication channel availability.
- Transmit and receive logic.
- Permissive conditions.
- Blocking conditions.
- Weak-infeed logic.
- Current reversal logic.
- Channel failure response.
- Local and remote trip logic.
19.7 SELogic configuration
Review the logic equations and confirm that each protection element operates the correct output contact.
The trip logic must be consistent with the circuit breaker arrangement and the intended single-pole or three-pole tripping scheme.
20. SEL-321 testing and commissioning
Testing the SEL-321 requires verification of the protection elements, directional characteristics, communication logic, breaker control and event recording.
OMICRON CMC test equipment and other suitable secondary-injection systems can be used to perform these tests.
20.1 Visual inspection
Check:
- Relay model and serial number.
- Hardware version.
- Auxiliary supply rating.
- CT and VT terminal connections.
- Trip and close circuits.
- Communication wiring.
- Input and output contacts.
- Earthing and panel connections.
20.2 Auxiliary supply test
Verify the DC auxiliary supply.
Check that the relay starts correctly and that no self-test or diagnostic alarm remains active.
20.3 CT and VT circuit testing
Verify:
- CT ratio.
- CT polarity.
- Phase sequence.
- VT ratio.
- Voltage phase rotation.
- Secondary grounding.
- Wiring continuity.
- Absence of unwanted short circuits or open circuits.
20.4 Distance protection testing
Test the phase and ground distance elements using the impedance test mode of the relay test set.
Typical test points include:
- Zone 1 forward reach.
- Zone 2 forward reach.
- Zone 3 forward and reverse reach.
- Zone 4 forward or reverse reach.
- Ground mho characteristics.
- Ground quadrilateral characteristics.
- Resistive reach.
- Directional boundaries.
The test set should inject the correct phase quantities for each fault type.
20.5 Directional element testing
Verify directional operation for:
- Forward faults.
- Reverse faults.
- Phase-to-phase faults.
- Phase-to-ground faults.
- Negative-sequence directional conditions.
20.6 Overcurrent testing
Test phase, negative-sequence and residual overcurrent elements.
Verify pickup, dropout and operating time against the approved settings.
20.7 Communication scheme testing
For communications-assisted protection, test the complete scheme between the two terminals.
Typical checks include:
| Test | Expected result |
|---|---|
| Forward internal fault | Correct permissive or trip response |
| Reverse external fault | No unwanted trip |
| Communication channel failure | Correct backup response |
| Weak-infeed condition | Correct configured logic |
| Current reversal | Correct blocking or permissive behavior |
| Direct transfer trip | Correct remote trip response |
| Restoration of channel | Correct recovery and alarm reset |
20.8 Single-pole tripping tests
For single-pole applications, verify:
- Faulted-phase selection.
- Single-pole trip output.
- Open-pole interval logic.
- Phase-discordance detection.
- Three-pole backup trip.
- Reclosing interlocks where applicable.
20.9 Power-swing and load-encroachment tests
Verify that power-swing blocking and load encroachment logic operate according to the approved settings and protection philosophy.
These functions are particularly important for heavily loaded transmission lines and systems subject to stability disturbances.
20.10 Event report analysis
After testing, retrieve the event records and review:
- Fault identification.
- Voltage and current measurements.
- Distance element operation.
- Directional element status.
- Trip logic.
- Communication status.
- Circuit breaker input and output states.
- Calculated fault location.
The event report is useful for confirming that the relay operated according to the intended protection scheme.
Safety note: Never open an energized CT secondary circuit. Follow the manufacturer’s instruction manual, approved test procedure and site safety rules when testing the relay.
21. Software used with the SEL-321
acSELerator QuickSet SEL-5030
QuickSet is used to configure, commission and manage supported SEL devices.
For the SEL-321, it provides access to relay settings and configuration functions.
SEL-5601-2 Synchrowave Event
Synchrowave Event is used to display and analyze relay event reports and COMTRADE files.
It helps protection engineers examine oscillographic records, voltage and current waveforms, and relay operation during system disturbances.
acSELerator Team SEL-5045
SEL identifies Team software for automatic collection and database management of relay event reports.
Availability and compatibility should be checked for the installed relay and software environment.
22. SEL-321 versus SEL-311C
The SEL-311C is one of the replacement products recommended by SEL for the discontinued SEL-321.
| Feature | SEL-321 | SEL-311C |
|---|---|---|
| Main application | Phase and ground distance protection | Transmission-line protection |
| Product status | Discontinued | Check current product status |
| Distance protection | Four zones | Advanced distance protection |
| Ground characteristics | Mho and quadrilateral | Model-specific protection options |
| Communications-assisted schemes | POTT, PUTT, DCB, DCUB, DUTT, DTT | Supported protection scheme options |
| Single-pole tripping | Supported | Supported on applicable configurations |
| Load encroachment | Included | Check applicable configuration |
| Engineering software | QuickSet | QuickSet |
| Retrofit use | Existing installations | SEL-recommended replacement option |
The SEL-311C is not necessarily a settings-compatible drop-in replacement. A replacement project requires an engineering review of CT/VT wiring, trip circuits, communications, logic, settings and panel dimensions.
23. SEL-321 product status and replacement considerations
The SEL-321 and SEL-321-5 are no longer in production.
SEL recommends the following products as replacements:
- SEL-311C Transmission Protection System
- SEL-9L Line Relay
SEL also states that a direct-replacement assembly is planned for the SEL-9L to reduce wiring changes and simplify retrofits when that product is released.
For existing SEL-321 installations, engineers should consider:
- Identifying the exact SEL-321 variant.
- Recording the firmware and hardware information.
- Retrieving the existing settings.
- Backing up protection logic and event records.
- Checking the availability of replacement parts and technical support.
- Evaluating the recommended replacement relay.
- Performing a complete protection and control design review before replacement.
24. Advantages of the SEL-321
The SEL-321 offered several important features for its generation:
- Four zones of phase and ground distance protection.
- Mho and quadrilateral ground distance characteristics.
- Flexible communications-assisted protection.
- Single-pole and three-pole tripping.
- Weak-infeed logic.
- Load encroachment protection.
- Power-swing blocking and out-of-step tripping.
- Six independent settings groups.
- Programmable SELogic control equations.
- Integrated fault locator.
- Oscillographic event reporting.
- Flexible contact inputs and outputs.
These capabilities explain why the SEL-321 became a useful platform in many transmission-line protection installations.
25. Frequently asked questions about the SEL-321
Q1. What is the main function of the SEL-321 relay?
The SEL-321 is a phase and ground distance protection relay designed primarily for HV, EHV and subtransmission overhead lines.
Q2. How many distance protection zones does the SEL-321 provide?
It provides four zones of phase and ground distance protection. Ground distance protection supports mho and quadrilateral characteristics.
Q3. Does the SEL-321 support POTT and DCB schemes?
Yes. The relay supports POTT, PUTT, DCB, DCUB, DUTT and DTT communications-assisted protection schemes.
Q4. Does the SEL-321 support single-pole tripping?
Yes. It includes phase selection, open-pole interval protection and phase-discordance logic for applicable single-pole tripping applications.
Q5. What is the purpose of load encroachment protection?
Load encroachment helps prevent unwanted distance relay operation during heavy loading when the apparent impedance approaches the distance protection characteristic.
Q6. What is the purpose of the negative-sequence directional element?
It helps determine fault direction during unbalanced system conditions and supports secure ground and negative-sequence protection.
Q7. Can the SEL-321 protect series-compensated transmission lines?
SEL’s product information identifies series-compensated line applications for the SEL-321 family. However, the exact model, compensation arrangement and protection settings must be evaluated before applying it to a particular project.
Q8. Which software is used to configure the SEL-321?
The relay is supported by acSELerator QuickSet SEL-5030. Synchrowave Event can be used to analyze oscillographic records.
Q9. Is the SEL-321 still manufactured?
No. SEL identifies the SEL-321 as no longer in production.
Q10. Which relay replaces the SEL-321?
SEL recommends the SEL-311C or SEL-9L for the SEL-321 family. The appropriate replacement depends on the application and retrofit requirements.

26. Practical protection relay training by Elec-Engg
Understanding the SEL-321 requires a good knowledge of transmission-line protection, distance relay characteristics, directional elements, communication-assisted tripping schemes, CT and VT circuits, and secondary-injection testing.
At Elec-Engg, we provide practical training for protection, commissioning, operation and maintenance engineers.
Our training subjects include:
- Transmission-line distance protection.
- Mho and quadrilateral characteristics.
- Phase and ground distance protection.
- POTT, PUTT, DCB and DCUB schemes.
- CT and VT circuit testing.
- Protection relay settings and coordination.
- OMICRON CMC and Test Universe.
- SEL and Siemens SIPROTEC protection relays.
Online training and customized company training can be arranged based on the requested subject and project requirements.
For further information, visit https://elec-engg.com/.
