SEL Digital Substation Architecture | IEC 61850, GOOSE and Process Bus

Digital substation technology is transforming the way electrical utilities design, operate, protect and maintain high-voltage substations. Traditional protection and control systems rely heavily on copper wiring between current transformers (CTs), voltage transformers (VTs), protection relays, circuit breakers and control panels. Modern digital secondary systems use intelligent electronic devices (IEDs), fiber-optic communication and standardized protocols to exchange measurement, protection, control and monitoring information.

Schweitzer Engineering Laboratories (SEL) offers digital substation solutions based on IEC 61850, Sampled Values (SV), Generic Object-Oriented Substation Event (GOOSE), Precision Time Protocol (PTP), Parallel Redundancy Protocol (PRP) and its proprietary Time-Domain Link (TiDL) technology.

This article provides a practical engineering overview of SEL digital substation architecture, including station-level, bay-level and process-level devices, communication networks, protection relays, merging units, time synchronization, redundancy, cybersecurity and commissioning.

It is intended for protection engineers, substation automation engineers, commissioning engineers and professionals involved in the design and maintenance of digital substations.

SEL Digital Substation Architecture: Complete Guide to Station Bus, Process Bus, GOOSE, Sampled Values, PRP and PTP

Table Of Contents
  1. 1. What is a digital substation?
  2. 2. Conventional versus digital substation architecture
  3. 3. Three levels of a digital substation
  4. 4. Station bus architecture
  5. 5. Process bus architecture
  6. 6. Understanding IEC 61850 communication services
  7. 7. SEL SV-based process bus solution
  8. 8. SEL TiDL process bus architecture
  9. 9. GOOSE communication in a digital substation
  10. 10. Sampled Values in a digital substation
  11. 11. PTP time synchronization architecture
  12. 12. Network redundancy using PRP
  13. 13. Cybersecurity in digital substations
  14. 14. Engineering software for SEL digital substations
  15. 15. Practical digital substation engineering example
  16. 16. Commissioning and testing of a digital substation
  17. 17. Common digital substation engineering mistakes
  18. 18. Digital substation versus conventional substation: advantages and considerations
  19. 19. Frequently asked questions
  20. 20. Practical digital substation and SEL relay training
  21. Official references and further reading

1. What is a digital substation?

A digital substation uses digital communication technologies to exchange information between protection, automation, control and monitoring equipment.

In a conventional substation, many signals are transmitted through dedicated copper cables:

  • CT secondary currents.
  • VT secondary voltages.
  • Circuit breaker position.
  • Disconnector and earthing switch status.
  • Protection trip commands.
  • Breaker failure initiation.
  • Interlocking signals.
  • Alarm and indication signals.

In a digital secondary system, many of these signals can be digitized and transmitted through communication networks.

For example:

  • A merging unit digitizes CT and VT measurements.
  • Sampled Values transmit digital current and voltage measurements.
  • GOOSE transmits protection and control events.
  • MMS provides communication between IEDs and supervisory systems.
  • PTP synchronizes measurement sampling and other time-dependent functions.
  • PRP can provide redundant Ethernet communication paths.

The objective is to reduce secondary wiring, simplify integration, improve diagnostics and create a flexible protection and automation architecture.

Important terminology: SEL commonly uses the term Digital Secondary Systems rather than claiming that the entire electrical substation is digital. The primary power system still carries electrical energy in its conventional physical form; the digital transformation primarily concerns secondary protection, automation, control and monitoring systems.

2. Conventional versus digital substation architecture

Conventional substation

A traditional protection and control architecture typically includes:

  1. CTs and VTs connected to protection relays through copper cables.
  2. Protection relays connected to circuit breaker trip coils.
  3. Auxiliary contacts wired to control and indication panels.
  4. Bay control units connected to switchgear.
  5. RTUs or automation controllers collecting information from IEDs.
  6. SCADA systems receiving information through communication protocols.

A conventional system is well understood and widely used. However, large substations can require extensive secondary cabling, terminal blocks, cable trenches and testing arrangements.

Digital secondary system

In a digital architecture, selected measurement and status signals are digitized close to the primary equipment.

The digital information is exchanged between devices using Ethernet or other supported communication technologies.

For an IEC 61850 SV-based architecture:

  • Merging units acquire analog measurements.
  • SV streams carry sampled current and voltage.
  • GOOSE carries event-based protection and control information.
  • Protection relays subscribe to the required data.
  • Station-level systems collect information through MMS and other supported protocols.

The architecture can reduce copper wiring and make it easier to share information between protection and automation devices.

3. Three levels of a digital substation

A common way to understand substation automation architecture is to divide it into three functional levels:

  • Station level.
  • Bay level.
  • Process level.

These levels describe the functions performed by devices. They are not necessarily three physically separate Ethernet networks.

3.1 Station level

The station level provides overall substation monitoring, control, automation and communication with external systems.

Typical equipment includes:

  • SCADA servers.
  • Human-machine interface (HMI).
  • Substation automation controllers.
  • Gateway devices.
  • Engineering workstations.
  • Event and disturbance record databases.
  • Network management systems.
  • Time synchronization equipment.

Typical functions include:

  • Supervisory control.
  • Alarm and event collection.
  • Remote monitoring.
  • Data acquisition.
  • Communication with the control centre.
  • Engineering access.
  • Historical data management.

SEL equipment used in station-level applications can include:

  • SEL-3530 RTAC.
  • SEL-3555 automation controller.
  • SEL-3355 computing platform.
  • SEL-2488 satellite-synchronized network clock.

The selected devices depend on the required automation, gateway, HMI and communication functions.

3.2 Bay level

The bay level contains the IEDs responsible for protection, control and monitoring of individual substation bays.

A bay may contain:

  • Line protection relay.
  • Transformer protection relay.
  • Feeder protection relay.
  • Busbar protection relay.
  • Bay control unit.
  • Metering device.
  • Breaker failure protection.
  • Disturbance recorder.

Examples of SEL protection devices include:

SEL relayTypical application
SEL-751Feeder protection
SEL-451Protection, automation and bay control
SEL-421Transmission line protection
SEL-411LLine current differential protection
SEL-487BBus differential and breaker failure protection
SEL-487ETransformer protection
SEL-700GGenerator protection

In an IEC 61850 process bus system, bay-level relays may subscribe to SV streams from merging units and exchange GOOSE messages with other IEDs.

3.3 Process level

The process level interfaces with the primary electrical equipment.

Typical equipment includes:

  • Current transformers.
  • Voltage transformers.
  • Circuit breakers.
  • Disconnectors.
  • Earthing switches.
  • Instrument transformer sensors.
  • Merging units.
  • Intelligent merging units.
  • Remote input/output devices.

The process level acquires measurements and equipment status and makes them available to protection and control devices.

In an SV-based architecture, merging units digitize analog measurements and publish them to the process bus.

In a TiDL architecture, SEL-TMU devices digitize measurements and binary signals and communicate directly with compatible TiDL-enabled relays using SEL T-Protocol.

4. Station bus architecture

The station bus connects station-level systems with bay-level IEDs and other compatible devices.

It is used for supervisory communication, monitoring, automation and engineering functions.

Main station bus communication services

MMS — Manufacturing Message Specification

MMS is commonly used for client-server communication between IEC 61850 servers and clients.

Typical applications include:

  • Reading measurements.
  • Reading equipment status.
  • Receiving reports.
  • Monitoring protection events.
  • Supervisory control.
  • Accessing supported data objects.

GOOSE — Generic Object-Oriented Substation Event

GOOSE can also be used for station-level and bay-level event communication, depending on the application.

Examples include:

  • Interlocking.
  • Protection blocking.
  • Breaker status.
  • Trip transfer.
  • Alarm and control signals.

Other communication protocols

Depending on the project, station-level systems may also use:

  • DNP3.
  • Modbus TCP.
  • IEC 60870-5-104.
  • FTP or SFTP.
  • SNMP.
  • Time synchronization protocols.

The exact protocol selection depends on the utility’s requirements and the supported interfaces of the equipment.

Example station bus architecture

Consider a substation with four feeder bays, one transformer bay and one busbar protection system.

The station bus connects the protection relays and bay control devices to the automation controller.

The RTAC collects information such as:

  • Feeder current and voltage.
  • Circuit breaker position.
  • Protection operation.
  • Transformer alarms.
  • Busbar protection status.
  • Disturbance information.

The RTAC can then provide the required information to the station HMI and remote SCADA control centre.

5. Process bus architecture

The process bus connects process-level devices with protection and control IEDs.

In an IEC 61850 SV-based process bus, the principal communication services are:

  • Sampled Values.
  • GOOSE.
  • PTP.

Main process bus components

1. Merging units

Merging units receive analog current and voltage measurements and convert them into digital Sampled Values streams.

2. Protection relays

Protection relays receive the digital measurement streams and perform protection functions.

3. Ethernet switches

Managed Ethernet switches provide the network infrastructure for the process bus.

4. PTP clock

A suitable time source and PTP architecture synchronize the devices that require a common time reference.

5. Fiber-optic connections

Fiber-optic communication connects the merging units, switches and protection relays.

Example process bus application

A feeder bay contains CTs and VTs connected to an SEL merging unit.

The merging unit publishes the required measurement stream.

An SEL protection relay subscribes to that stream and processes the current and voltage measurements.

If a fault occurs, the protection relay operates and may publish a GOOSE trip command to a compatible circuit breaker control device.

This architecture replaces selected analog measurement and binary signal connections with digital communication.

6. Understanding IEC 61850 communication services

A digital substation may use several IEC 61850 communication services simultaneously.

ServiceMain functionTypical application
MMSClient-server communicationSCADA, HMI and monitoring
GOOSEFast event-based communicationTrip, block and interlocking
Sampled ValuesDigital analog measurement transmissionCT/VT measurements
PTPTime synchronizationAlignment of sampled measurements
SCLConfiguration and system descriptionIED integration and engineering

MMS

MMS provides structured communication between clients and servers.

For example, a station HMI can retrieve measurements and status information from an SEL protection relay through its IEC 61850 server.

GOOSE

GOOSE provides high-speed event communication between IEDs.

For example, an SEL-751 feeder relay can publish a protection trip indication that another compatible IED subscribes to.

Sampled Values

SV transmits digitized current and voltage measurements.

For example, an SEL merging unit publishes three-phase current and voltage samples to an SV-compatible protection relay.

PTP

PTP synchronizes the devices that need a common time reference.

This is especially important when multiple merging units provide measurements to a protection application that compares their samples.

SCL

Substation Configuration Language is used to describe and exchange IEC 61850 system configuration information.

Common file types include:

  • ICD — IED Capability Description.
  • IID — Instantiated IED Description.
  • CID — Configured IED Description.
  • SCD — Substation Configuration Description.

SCL is a central part of engineering multi-vendor IEC 61850 systems.

7. SEL SV-based process bus solution

SEL offers process bus solutions based on IEC 61850 Sampled Values and GOOSE.

The architecture uses merging units, protection relays, fiber-optic communication and time synchronization.

Merging units

Merging units are installed close to the primary equipment.

They can:

  • Digitize analog current measurements.
  • Digitize analog voltage measurements.
  • Publish SV streams.
  • Digitize additional binary signals.
  • Exchange GOOSE messages.
  • Provide diagnostics and event information.

SEL’s process bus solutions include intelligent merging unit capabilities in selected configurations.

These capabilities can provide additional protection and control functions close to the primary equipment.

Protection relays

Protection relays subscribe to the required measurement streams and perform their assigned functions.

Examples include:

  • Feeder protection.
  • Distance protection.
  • Line differential protection.
  • Bus differential protection.
  • Transformer differential protection.

The actual SV publisher and subscriber capabilities depend on the exact product variant and ordering configuration.

Communication network

The process bus network transports SV and GOOSE messages between the relevant devices.

The network must be designed for:

  • Required bandwidth.
  • Low and predictable communication delay.
  • Multicast traffic handling.
  • Redundancy.
  • Network diagnostics.
  • Cybersecurity.

Time synchronization

PTP is used in networked SV architectures to synchronize relevant devices.

A common time reference helps align the measurement samples from different merging units.

8. SEL TiDL process bus architecture

SEL also provides a different process bus approach called Time-Domain Link (TiDL).

TiDL is designed to simplify digital secondary system implementation using direct fiber-optic connections and SEL’s proprietary T-Protocol.

Unlike a networked IEC 61850 SV architecture, TiDL does not require conventional Ethernet network engineering between its merging units and TiDL-enabled relays.

Main TiDL components

SEL-TMU — TiDL Merging Unit

The SEL-TMU is installed close to the primary equipment.

It digitizes:

  • Current measurements.
  • Voltage measurements.
  • Circuit breaker status.
  • Other supported binary signals.

The information is transmitted through fiber-optic links to compatible TiDL-enabled protection relays.

TiDL-enabled protection relays

Compatible SEL relays receive the T-Protocol data streams and use them for protection and control functions.

Main TiDL characteristics

  • Direct point-to-point fiber-optic connections.
  • No conventional Ethernet process bus network required between the TMU and relay.
  • No external PTP time reference required for the TiDL measurement synchronization method.
  • Simplified communication configuration.
  • Automatic commissioning and communication monitoring features.

SEL documentation describes the ability of an SEL-TMU to connect directly to as many as four compatible TiDL-enabled relays. Confirm the current product documentation for the exact hardware and configuration.

TiDL versus IEC 61850 Sampled Values

FeatureSEL TiDLIEC 61850 SV
CommunicationSEL T-ProtocolIEC 61850 SV
ConnectionDirect fiber-optic linksDirect or networked Ethernet
Ethernet process busNot required for TMU-to-relay linksUsed in networked implementations
External PTP referenceNot required for TiDL measurement synchronizationCommonly used in networked process bus systems
InteroperabilitySEL TiDL ecosystemStandardized IEC communication, subject to compatible profiles
ConfigurationSEL-specific workflowIEC 61850 engineering and SCL workflow
Network engineeringSimplified point-to-point architectureRequires network engineering for networked implementations

TiDL and SV are different engineering approaches. They should not be treated as interchangeable protocols.

9. GOOSE communication in a digital substation

GOOSE is used for fast exchange of event-based information between IEDs.

Typical applications include:

  • Feeder trip transfer.
  • Breaker failure initiation.
  • Busbar protection trip.
  • Transformer lockout.
  • Protection blocking.
  • Interlocking.
  • Circuit breaker status.
  • Disconnector status.

Example: Feeder trip to busbar protection

Consider a substation with an SEL-751 feeder relay and an SEL-487B bus differential relay.

The feeder relay detects a fault and publishes a GOOSE signal.

The busbar protection system subscribes to the signal and uses it as part of the engineered application.

The complete scheme must include:

  1. Publisher configuration.
  2. Dataset definition.
  3. GOOSE control block configuration.
  4. Subscriber configuration.
  5. Signal mapping.
  6. Application logic.
  7. Communication supervision.
  8. End-to-end testing.

GOOSE communication does not automatically provide the complete protection logic. Engineers must define the required application and its response to communication failure.

10. Sampled Values in a digital substation

Sampled Values are used to transmit digital current and voltage measurements.

In a conventional system, a CT or VT secondary circuit is connected directly to a protection relay.

In an SV-based process bus, the measurement is digitized by a merging unit and transmitted through Ethernet.

Example: Transformer differential protection

Consider a power transformer with two winding-side merging units.

  • MU1 measures the transformer high-voltage-side currents.
  • MU2 measures the transformer low-voltage-side currents.
  • Both merging units publish their SV streams.
  • The transformer differential relay subscribes to both streams.
  • The relay performs differential protection calculations.

For correct operation, the engineering design must consider:

  • CT ratio and polarity.
  • Transformer vector group.
  • Current scaling.
  • Sample synchronization.
  • Measurement quality.
  • Network performance.
  • Protection relay settings.
  • Response to communication failure.

The relay must support the required number and type of SV streams.

11. PTP time synchronization architecture

PTP is an important part of many networked process bus implementations.

It is based on IEEE 1588 and provides a mechanism for synchronizing clocks over a communication network.

Typical PTP architecture

  1. A suitable time reference, such as a satellite-synchronized clock.
  2. A PTP grandmaster.
  3. PTP-aware Ethernet network infrastructure, where required.
  4. Merging units.
  5. Protection relays.

Why is synchronization important?

Consider a line differential protection scheme.

Two merging units measure currents at opposite ends of a protected line.

The relay compares the measurements to determine whether the fault is inside or outside the protected zone.

If the measurements are not properly time-aligned, the differential calculation can be affected.

Therefore, the design must consider:

  • PTP profile compatibility.
  • Clock accuracy.
  • Network asymmetry.
  • Synchronization monitoring.
  • Loss of time reference.
  • Recovery after synchronization returns.

The exact PTP architecture and response to synchronization failure must follow the selected devices’ documentation and the protection design.

12. Network redundancy using PRP

Protection and control systems require reliable communication.

An Ethernet network failure must not create an unacceptable loss of protection or control functionality.

Parallel Redundancy Protocol (PRP) is one technology used to improve communication availability.

PRP is defined in IEC 62439-3.

How PRP works

A PRP network uses two independent LANs:

  • LAN A.
  • LAN B.

A PRP-capable device sends duplicate frames through both networks.

The receiving device accepts the first valid frame and discards the duplicate.

This provides seamless communication continuity for a single network failure, provided the two networks and devices are correctly engineered.

Example PRP architecture

Consider an SV-based process bus with:

  • SEL merging units.
  • SEL protection relays.
  • Ethernet switches in LAN A.
  • Ethernet switches in LAN B.

The merging units and protection relays communicate through both networks.

If one network fails, the other can continue delivering messages without requiring the normal application to wait for network reconvergence.

Important PRP engineering considerations

  • LAN A and LAN B should be independent.
  • Avoid unintended common points of failure.
  • Verify PRP compatibility of each device.
  • Check the network topology.
  • Confirm correct PRP configuration.
  • Test the loss of each LAN separately.
  • Verify that alarms identify communication failures.

PRP does not eliminate the need for network diagnostics. A redundant network can continue operating while one communication path has silently failed.

SEL describes additional monitoring and diagnostic capabilities for detecting certain data-flow failures in its process bus solutions. The exact capability depends on the equipment and network implementation.

13. Cybersecurity in digital substations

Digital substations introduce additional communication interfaces and network infrastructure.

Cybersecurity must therefore be considered from the beginning of the engineering design.

Important areas include:

Network segmentation

Separate communication services and operational functions where appropriate.

For example:

  • Process bus network.
  • Station bus network.
  • Engineering access network.
  • Remote SCADA connection.

Access control

Apply appropriate controls for:

  • Engineering workstations.
  • Relay configuration.
  • Remote access.
  • User authentication.
  • Network administration.

Network monitoring

Monitor:

  • Unexpected communication.
  • Device connection changes.
  • Network faults.
  • Configuration changes.
  • Communication alarms.

Secure configuration management

Maintain approved copies of:

  • Relay settings.
  • SCL files.
  • Network configuration.
  • Firmware versions.
  • Test reports.
  • Engineering change records.

IEC 62351

IEC 62351 contains cybersecurity standards for power system communications.

The relevant parts and implementation requirements depend on the communication service, system design and supported device capabilities.

Do not assume that every SEL relay supports every IEC 62351 security function.

14. Engineering software for SEL digital substations

Several software tools may be used during digital substation engineering.

acSELerator Architect SEL-5032

Architect is used for IEC 61850 system engineering.

Typical applications include:

  • SCL file management.
  • IED integration.
  • GOOSE configuration.
  • Sampled Values configuration.
  • MMS configuration.
  • Communication documentation.

acSELerator QuickSet SEL-5030

QuickSet is primarily used for SEL relay settings and supported programmable logic.

Typical activities include:

  • Protection setting configuration.
  • Relay logic.
  • Device settings management.
  • Reviewing supported relay configuration parameters.

SEL Grid Configurator SEL-5037

Grid Configurator is used to configure and manage settings for supported SEL devices, including relevant digital secondary system products.

Wireshark

Wireshark is a packet analysis tool useful for troubleshooting Ethernet-based IEC 61850 communication.

Engineers can use it to inspect:

  • GOOSE messages.
  • Sampled Values.
  • Ethernet VLAN tags.
  • APPID.
  • Multicast addresses.
  • Sample counters.
  • Communication timing.

SEL Device Management and Automation tools

SEL provides additional tools for device management, automation and collection of information such as event reports and sequence-of-events records.

The exact software workflow depends on the selected equipment and project requirements.

15. Practical digital substation engineering example

Consider a 132 kV substation with:

  • Two incoming transmission lines.
  • One power transformer.
  • Six outgoing feeders.
  • One busbar protection system.
  • One station automation system.

A digital secondary system could be designed as follows.

Line bays

Each line bay contains:

  • Line protection relay.
  • Merging unit or compatible process interface.
  • Circuit breaker control.
  • GOOSE communication.
  • SV measurement stream, where applicable.

Transformer bay

The transformer bay contains:

  • Transformer differential relay.
  • Backup protection relay.
  • Merging units for the required measurement locations.
  • Transformer alarm and temperature monitoring.
  • GOOSE communication with associated bay devices.

Feeder bays

Each feeder bay contains:

  • Feeder protection relay.
  • Current and voltage measurement interface.
  • Circuit breaker control.
  • GOOSE interlocking and protection communication.

Busbar protection

The busbar protection system receives the required current measurements and status information.

It performs bus differential protection and associated breaker failure functions according to the engineered design.

Station automation

An RTAC or suitable automation controller collects information from the protection and control devices.

It provides:

  • Station HMI information.
  • Remote SCADA communication.
  • Alarm collection.
  • Control commands.
  • Event monitoring.

Network architecture

The project may use separate or appropriately segmented station and process bus networks.

The selected design should consider:

  • PRP or other supported redundancy.
  • VLANs.
  • Network bandwidth.
  • PTP synchronization.
  • Device interoperability.
  • Cybersecurity.
  • Maintenance access.

This is an example architecture, not a standard configuration that should be copied without a project-specific protection and network design.

16. Commissioning and testing of a digital substation

Commissioning a digital substation requires both protection testing and communication testing.

It is not sufficient to confirm that the Ethernet network is active.

Engineers must verify the complete chain from the primary measurement source to the final protection or control action.

16.1 Merging unit testing

Verify:

  • CT and VT input wiring.
  • Current and voltage polarity.
  • Measurement scaling.
  • Channel assignment.
  • SV publication.
  • GOOSE status publication, where applicable.
  • Time synchronization.
  • Device diagnostics.
  • Communication failure indications.

16.2 Sampled Values testing

Check:

  • Correct SVID.
  • Correct APPID.
  • Correct multicast address.
  • Correct VLAN.
  • Sample counter continuity.
  • Sample synchronization.
  • Measurement values.
  • Measurement quality.
  • Stream reception by the subscriber.

16.3 GOOSE testing

Check:

  • Publisher configuration.
  • Dataset entries.
  • GOOSE control block.
  • Subscriber configuration.
  • Signal mapping.
  • State changes.
  • Communication supervision.
  • Communication-loss response.

16.4 PTP testing

Check:

  • Grandmaster status.
  • PTP profile.
  • Clock synchronization.
  • Device time status.
  • Loss of synchronization.
  • Recovery after synchronization returns.

16.5 PRP testing

Test each network path separately.

For example:

  1. Verify normal operation with both LANs active.
  2. Disconnect LAN A using an approved test procedure.
  3. Verify communication continues through LAN B.
  4. Confirm that the failure is detected and alarmed.
  5. Restore LAN A.
  6. Repeat for LAN B.
  7. Confirm that both networks return to the intended operating condition.

16.6 End-to-end protection testing

Perform functional testing of the complete protection scheme.

For example, in a feeder protection application:

  1. Apply the required test current and voltage.
  2. Verify the measurement at the merging unit.
  3. Verify the SV stream.
  4. Verify the subscriber relay measurements.
  5. Test the protection element.
  6. Verify the trip logic.
  7. Verify the GOOSE or hardwired trip path.
  8. Verify the circuit breaker output interface.
  9. Record the test results.

Where a live circuit breaker is involved, follow the approved switching, isolation and safety procedures.

17. Common digital substation engineering mistakes

1. Treating station bus and process bus as identical

They serve different functional purposes and have different performance requirements.

Solution: Define the communication services and network requirements separately.

2. Incorrect SV stream configuration

The subscriber is configured for an incorrect stream, APPID, SVID or measurement structure.

Solution: Compare the actual stream with the approved configuration and device documentation.

3. Incorrect GOOSE mapping

The message is received but the required signal is not connected to the intended relay logic.

Solution: Verify the publisher dataset, subscription mapping and application logic.

4. Inadequate PTP design

Devices receive inconsistent synchronization or the time source is not sufficiently reliable.

Solution: Define the PTP profile, grandmaster architecture, network requirements and failure response.

5. Insufficient network redundancy testing

The system operates normally with both networks but a hidden fault remains in one path.

Solution: Test each redundant network independently and verify diagnostic alarms.

6. Ignoring cybersecurity

Engineering access and network segmentation are not adequately controlled.

Solution: Include cybersecurity requirements in the architecture and commissioning plans.

7. Testing only communication

The engineer confirms that packets are present but does not verify protection performance.

Solution: Perform end-to-end functional testing from measurement acquisition to final trip or control action.

18. Digital substation versus conventional substation: advantages and considerations

AreaConventional architectureDigital secondary system
Measurement transmissionAnalog copper wiringDigital SV or other supported technologies
Binary signal exchangeHardwired contactsGOOSE or other digital interfaces
CablingExtensive secondary copperGreater use of fiber optics
EngineeringWiring diagrams and terminal plansWiring plus communication and SCL engineering
DiagnosticsElectrical circuit testingDevice, protocol and network diagnostics
InteroperabilityPhysical and electrical interfacesStandardized protocols, subject to compatibility
TestingSecondary injection and hardwired checksDigital testing plus application and communication checks
CybersecurityPrimarily physical and device accessAdditional network and communication security requirements

Digital systems can reduce wiring and improve information sharing, but they require engineers to understand communication protocols, network design, configuration management and digital testing.

19. Frequently asked questions

What is a digital substation?

A digital substation uses digital communication and intelligent electronic devices for protection, automation, control and monitoring. It can use technologies such as IEC 61850, GOOSE, Sampled Values, PTP and Ethernet networks.

What is the difference between station bus and process bus?

The station bus mainly connects station-level systems with bay-level IEDs for monitoring, automation and supervisory communication. The process bus connects process-level equipment and bay-level IEDs for measurement, protection and control data exchange.

What is the role of GOOSE in a digital substation?

GOOSE exchanges event-based information such as protection trips, breaker status, interlocking and blocking signals between compatible IEDs.

What is the role of Sampled Values?

Sampled Values transmit digital representations of current and voltage measurements from merging units or other supported publishers to protection relays and other subscribers.

Why is PTP required?

PTP provides a common time reference for devices that require synchronized measurement sampling and time-dependent operation, particularly in networked process bus applications.

What is PRP?

PRP is a redundancy protocol defined in IEC 62439-3. It uses two independent LANs to provide seamless communication continuity for a single network failure when correctly implemented.

What is SEL TiDL?

TiDL is SEL’s proprietary Time-Domain Link technology. It uses direct fiber-optic connections between SEL-TMU merging units and compatible protection relays. It simplifies process bus networking and does not require an external PTP time reference for its measurement synchronization method.

Is TiDL the same as IEC 61850 Sampled Values?

No. TiDL uses SEL T-Protocol, while IEC 61850 SV uses standardized Sampled Values communication. They are different architectures with different engineering and interoperability characteristics.

Can SEL relays communicate with Siemens SIPROTEC relays?

Yes, multi-vendor IEC 61850 communication is possible when the selected devices support compatible services, data models and configuration requirements. Each GOOSE, MMS or SV application must be engineered and tested.

Can a digital substation operate without copper cables?

No. Digital secondary systems can substantially reduce copper wiring, but they do not eliminate all copper connections. Primary equipment, auxiliary supplies, trip circuits and other interfaces may still require conventional wiring depending on the architecture.

Which software is used for SEL digital substation engineering?

Common tools include acSELerator Architect SEL-5032, acSELerator QuickSet SEL-5030, SEL Grid Configurator SEL-5037 and Wireshark. The required tools depend on the device and communication architecture.

20. Practical digital substation and SEL relay training

Digital substation engineering requires knowledge of protection systems, relay configuration, IEC 61850 communication, Ethernet networks, time synchronization and commissioning.

Elec-Engg provides practical training in:

  • Power system protection and control.
  • SEL protection relays.
  • IEC 61850 station bus and process bus.
  • GOOSE publisher and subscriber configuration.
  • Sampled Values and merging units.
  • SEL TiDL technology.
  • acSELerator Architect.
  • SEL QuickSet and Grid Configurator.
  • Wireshark communication analysis.
  • PTP and PRP.
  • Digital substation testing and commissioning.

Training can be arranged online or customized for companies and engineering teams.

For further information, visit https://elec-engg.com/ or contact Elec-Engg.


Official references and further reading

  1. SEL Digital Secondary Systems
    https://selinc.com/solutions/digital-secondary-systems/
  2. SEL Sampled Values Process Bus Solutions
    https://selinc.com/solutions/digital-secondary-systems/sampled-values/
  3. SEL TiDL Process Bus Solutions
    https://selinc.com/solutions/digital-secondary-systems/time-domain-link/
  4. SEL Substation Automation Solutions
    https://selinc.com/solutions/substation-automation/
  5. SEL-5032 acSELerator Architect
    https://selinc.com/products/5032/
  6. SEL-2488 Satellite-Synchronized Network Clock
    https://selinc.com/products/2488/
  7. SEL Technical Paper: Designing IEC 61850 Digital Substation Process Bus to Meet Utility Protection and Testing Requirements
    https://selinc.com/api/download/142043/?lang=en
  8. SEL Technical Paper: Complete Monitoring Solution to Improve Reliability and Performance of Digital Secondary Systems
    https://selinc.com/api/download/138663/?lang=en

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top