GE Multilin Synchronism Check Protection (ANSI 25): Voltage Difference, Phase Angle, Slip Frequency, Live/Dead Bus Logic and Testing

Table Of Contents
  1. 1. Introduction
  2. 2. What Is Synchronism Check Protection?
  3. 3. Why Synchronism Check Is Necessary
  4. 4. Voltage Difference
  5. 5. Phase-Angle Difference
  6. 6. Frequency Difference and Slip Frequency
  7. 7. Relationship Between Slip Frequency and Phase Angle
  8. 8. Circuit-Breaker Closing Time Compensation
  9. 9. Typical Synchronism-Check Criteria
  10. 10. Live-Bus and Dead-Bus Supervision
  11. 11. Voltage Transformer Connections and Measurement
  12. 12. Synchronism Check and Autoreclosing (ANSI 79)
  13. 13. Synchronism Check and Generator Protection
  14. 14. GE Multilin Synchronism-Check Applications
  15. 15. General GE Multilin Engineering Workflow
  16. 16. Practical Synchronism-Check Calculation
  17. 17. Synchronism-Check Testing and Commissioning
  18. 18. Common Synchronism-Check Problems
  19. 19. Synchronism-Check Commissioning Checklist
  20. 20. Best Engineering Practices
  21. 21. Training on GE Multilin Protection Relays by Elec-Engg
  22. 22. Frequently Asked Questions
  23. 23. Related Articles
  24. Conclusion

1. Introduction

Synchronism check protection (ANSI 25) is an important function in power-system protection and substation control. It supervises circuit-breaker closing operations when two electrical systems may be energized independently.

Before connecting two energized systems, their voltage magnitudes, phase angles, and frequencies must be within acceptable limits. Closing a circuit breaker under unsuitable conditions can produce high transient currents, severe mechanical stress, electrical disturbances, and damage to generators, transformers, circuit breakers, and other equipment.

Synchronism check protection helps prevent these conditions by evaluating the electrical quantities on both sides of a circuit breaker and issuing a closing permissive only when the configured criteria are satisfied.

In GE Multilin applications, ANSI 25 functionality and its integration with breaker control depend on the exact relay model, firmware, and application. Some schemes use an integrated synchronism-check element, while others use a dedicated synchronism-check relay or external control logic.

This article explains synchronism-check principles, practical calculations, live-bus/dead-bus logic, autoreclosing integration, configuration considerations, and commissioning tests.

2. What Is Synchronism Check Protection?

Synchronism check is a supervision function that determines whether two electrical systems are suitable for connection through a circuit breaker.

Typical applications include:

  • Generator circuit-breaker closing.
  • Transmission-line energization.
  • Bus coupler closing.
  • Bus-section circuit-breaker closing.
  • Interconnection of two substations.
  • Restoration of supply after a network outage.
  • Automatic reclosing when both sides of the breaker may be energized.

The function normally compares voltage signals from the two sides of the circuit breaker.

The main quantities are:

  1. Voltage magnitude difference.
  2. Phase-angle difference.
  3. Frequency difference.
  4. Slip frequency.
  5. Voltage availability and validity.
  6. Synchronism-check time window.

If the required conditions are satisfied, the function provides a closing permissive to the circuit-breaker control logic.

Important: Synchronism check is not the same as synchronizing control. Synchronism check supervises a closing operation. An automatic synchronizer may actively adjust generator voltage, frequency, and phase angle to achieve synchronism before closing.

3. Why Synchronism Check Is Necessary

Consider two energized systems connected through a circuit breaker.

One side may be connected to a generator, while the other side is connected to the utility network.

If the breaker closes while the two systems have a significant phase-angle difference, the resulting electrical transient may be severe.

Possible consequences include:

  • High circulating current.
  • Electromagnetic torque disturbances.
  • Mechanical stress on generator shafts.
  • Transformer winding forces.
  • Voltage disturbances.
  • Circuit-breaker electrical stress.
  • Power-system instability.

The severity depends on the system impedance, voltage levels, phase-angle difference, generator characteristics, and operating conditions.

Synchronism-check protection reduces the risk of an unsuitable closing operation.

4. Voltage Difference

Voltage difference is one of the main synchronism-check criteria.

The relay compares the voltage magnitudes on both sides of the circuit breaker.

Let:

  • (V_1) = voltage magnitude on side 1.
  • (V_2) = voltage magnitude on side 2.

The absolute voltage difference is:

[
\Delta V = |V_1-V_2|
]

The percentage voltage difference may be calculated as:

[
\Delta V_{%} =
\frac{|V_1-V_2|}{V_{\text{reference}}}\times100
]

The reference voltage used by the relay or engineering calculation must be defined consistently.

Practical example

Assume:

  • Bus-side voltage = 110 kV.
  • Line-side voltage = 106 kV.

Then:

[
\Delta V=|110-106|=4\text{ kV}
]

Using 110 kV as the reference:

[
\Delta V_{%}=\frac{4}{110}\times100
]

[
\Delta V_{%}=3.64%
]

If the approved synchronism-check voltage-difference limit is 5%, this condition satisfies the voltage-magnitude criterion.

However, this does not mean that the breaker can close. The phase-angle, frequency, voltage-validity, and other permissive conditions must also be satisfied.

5. Phase-Angle Difference

The phase-angle difference represents the angular displacement between the two voltage phasors.

It is one of the most important parameters in synchronism-check engineering.

Let:

  • (\theta_1) = phase angle of voltage on side 1.
  • (\theta_2) = phase angle of voltage on side 2.

Then:

[
\Delta\theta=|\theta_1-\theta_2|
]

The difference must be evaluated using the correct angular convention, including the shortest relevant angular separation.

Example

Assume:

  • Bus voltage angle = (5^\circ).
  • Line voltage angle = (18^\circ).

Then:

[
\Delta\theta=|18-5|=13^\circ
]

If the approved phase-angle limit is (15^\circ), the phase-angle criterion is satisfied.

If the measured angle difference increases beyond the permitted value, the synchronism-check function should block the closing permissive.

Why phase-angle difference matters

When two energized systems are connected, the phase-angle difference determines the initial electrical stress associated with the connection.

For a simplified predominantly inductive system, the active power transfer relationship can be represented as:

[
P\approx\frac{V_1V_2}{X}\sin\delta
]

Where:

  • (V_1) and (V_2) are voltage magnitudes.
  • (X) is the equivalent transfer reactance.
  • (\delta) is the phase-angle difference.

This simplified relationship illustrates why the angle difference is important. Actual transient closing behavior requires a more complete system study.

6. Frequency Difference and Slip Frequency

Frequency difference determines how quickly the phase angle between the two systems changes.

Let:

  • (f_1) = frequency on side 1.
  • (f_2) = frequency on side 2.

Then:

[
\Delta f=|f_1-f_2|
]

The frequency difference is often referred to as slip frequency in synchronism-check applications.

Example

Assume:

  • Bus frequency = 50.00 Hz.
  • Line-side frequency = 50.08 Hz.

Then:

[
\Delta f=|50.08-50.00|
]

[
\Delta f=0.08\text{ Hz}
]

The two systems are not operating at exactly the same frequency. Therefore, their phase-angle difference changes with time.

A small frequency difference can still result in an unacceptable phase-angle difference if the closing operation is delayed.

7. Relationship Between Slip Frequency and Phase Angle

The phase-angle difference changes according to the frequency difference.

For a constant frequency difference:

[
\frac{d\delta}{dt}=360\Delta f
]

Where:

  • (\delta) is the phase-angle difference in degrees.
  • (\Delta f) is the frequency difference in hertz.
  • Time is measured in seconds.

For example, if:

[
\Delta f=0.1\text{ Hz}
]

Then the phase-angle difference changes at:

[
360\times0.1=36^\circ/\text{s}
]

If the initial phase-angle difference is (10^\circ), after one second it may have changed by approximately (36^\circ), assuming constant slip and the same direction of rotation.

This demonstrates why a synchronism-check function must consider both phase angle and slip frequency.

8. Circuit-Breaker Closing Time Compensation

A circuit breaker does not close instantaneously after receiving a close command.

There is a mechanical operating delay between the closing command and actual contact making.

During this interval, the phase-angle difference may continue changing.

For this reason, synchronism-check schemes may include closing-time compensation or advance-angle logic.

Example

Assume:

  • Slip frequency = 0.1 Hz.
  • Circuit-breaker closing time = 100 ms.

The expected phase-angle change during the closing time is:

[
\Delta\theta=360\times0.1\times0.1
]

[
\Delta\theta=3.6^\circ
]

The relay or associated synchronizing system may account for this expected change when determining the appropriate closing instant.

The exact compensation method depends on the device and scheme. Engineers must distinguish between a simple synchronism-check permissive and an automatic synchronizing controller that predicts the future phase relationship.

9. Typical Synchronism-Check Criteria

A synchronism-check scheme may include the following limits:

ParameterFunction
Voltage differenceChecks voltage magnitude compatibility
Phase-angle differenceChecks angular displacement
Slip frequencyChecks relative frequency
Voltage supervisionConfirms valid voltage measurements
Closing timeSupports closing-time compensation where available
Permissive durationDefines how long closing permission remains valid

The following values are illustrative only and must not be used as universal settings.

ParameterIllustrative value
Maximum voltage difference5%
Maximum phase-angle difference15°
Maximum slip frequency0.1 Hz
Breaker closing time100 ms

Actual settings must be determined from the network study, equipment requirements, utility standards, and the applicable relay documentation.

10. Live-Bus and Dead-Bus Supervision

Not every circuit-breaker closing operation requires two energized systems to be synchronized.

Some applications involve connecting an energized bus to a dead line, or an energized line to a dead bus.

Live/dead supervision is therefore an important part of many breaker-closing schemes.

10.1 Live bus / dead line

In this condition:

  • The bus is energized.
  • The line is de-energized.
  • The closing scheme may permit energization of the line.

The voltage measurements must be valid and the dead-line threshold must be correctly defined.

10.2 Dead bus / live line

In this condition:

  • The line is energized.
  • The bus is de-energized.
  • The scheme may permit closing to energize the bus.

This condition is sometimes used during restoration operations.

10.3 Live bus / live line

Both sides are energized.

The synchronism-check function should supervise the closing operation using the required voltage, phase-angle, and frequency criteria.

10.4 Dead bus / dead line

Both sides are de-energized.

The closing philosophy must be defined by the network operator. Some schemes may permit closing under this condition, while others may block it or require additional checks.

Example of closing logic

Bus sideLine sideTypical supervision
LiveDeadLive-bus/dead-line permissive
DeadLiveDead-bus/live-line permissive
LiveLiveSynchronism check
DeadDeadScheme-dependent

These conditions are not universal. The actual voltage thresholds, supervision timers, and closing permissions must be specified in the approved control philosophy.

11. Voltage Transformer Connections and Measurement

Synchronism-check reliability depends on correct voltage measurement.

The relay must receive suitable voltage signals from both sides of the circuit breaker.

Typical measurement arrangements include:

  • Bus VT and line VT.
  • Bus VT and line-side CVT.
  • Generator terminal VT and bus VT.
  • Two independent bus-section voltage measurements.

The protection engineer must verify:

  1. VT ratios.
  2. Primary and secondary voltage ratings.
  3. Phase assignment.
  4. Phase sequence.
  5. Polarity and reference connections.
  6. VT fuse supervision.
  7. Correct phase-to-phase or phase-to-neutral measurement.
  8. Voltage input configuration.

11.1 Phase-sequence verification

If the phase sequence is incorrect on one side, the measured angle relationship may be wrong.

This can cause false blocking or, more seriously, an incorrect closing permissive.

The phase sequence must be verified during commissioning.

11.2 VT failure supervision

Loss of voltage due to a blown VT fuse, wiring problem, or measurement circuit failure can produce misleading synchronism-check quantities.

The scheme should include appropriate voltage supervision and failure handling.

A failed voltage measurement must not be interpreted automatically as a genuinely dead bus or dead line.

12. Synchronism Check and Autoreclosing (ANSI 79)

Synchronism check is frequently integrated into transmission-line autoreclosing schemes.

After a line fault:

  1. The line protection trips the circuit breaker.
  2. The autoreclosing function starts its sequence.
  3. The breaker opens.
  4. The dead-time interval expires.
  5. The closing logic checks the required conditions.
  6. If both sides are energized, synchronism check may be required.
  7. If the conditions are acceptable, a closing permissive is issued.
  8. The circuit breaker receives a closing command.

The exact sequence depends on the line arrangement and the utility’s operating philosophy.

Practical considerations

The engineer should verify:

  • Whether synchronism check is required for every reclose shot.
  • Whether live-line/dead-bus closing is permitted.
  • Whether dead-line/live-bus closing is permitted.
  • Whether voltage supervision is available.
  • Whether the closing command is supervised by an external interlock.
  • Whether the breaker closing time is considered.

13. Synchronism Check and Generator Protection

Generator circuit-breaker closing is a particularly important application of synchronism check.

A generator must be synchronized with the power system before being connected in parallel.

The relevant quantities include:

  • Generator voltage.
  • Bus voltage.
  • Generator frequency.
  • System frequency.
  • Phase-angle difference.
  • Generator and breaker closing times.

13.1 Synchronizing a generator

A typical generator synchronization procedure involves:

  1. Starting the generator.
  2. Establishing rated or approved terminal voltage.
  3. Adjusting generator speed and frequency.
  4. Comparing generator and bus voltage.
  5. Comparing phase angles.
  6. Confirming acceptable slip frequency.
  7. Issuing a closing command when the conditions are suitable.

An automatic synchronizer may adjust the generator excitation and governor controls. The synchronism-check relay provides a supervision function and may issue a closing permissive.

13.2 Synchronism check versus automatic synchronizing

FunctionSynchronism checkAutomatic synchronizing
Measures voltage differenceYesYes
Measures phase-angle differenceYesYes
Evaluates frequency differenceYes, where supportedYes
Adjusts generator speedNoUsually
Adjusts generator voltageNoUsually
Provides closing permissiveYesOften
Controls synchronization processNoYes

A synchronism-check relay should not be assumed to perform all functions of an automatic synchronizer.

14. GE Multilin Synchronism-Check Applications

GE Multilin relay capabilities vary by product family and firmware.

The engineer should identify the exact device before designing the synchronism-check scheme.

Potential application areas include:

  • Generator protection.
  • Transmission-line protection.
  • Feeder and breaker control.
  • Bus coupler control.
  • Substation automation.
  • Integrated protection and control schemes.

Some GE Multilin products may provide synchronism-check functionality, while other installations use a separate synchronism-check device or external control logic.

For example, generator protection applications involving GE Multilin G60, G30, or 889 relays should be checked against the specific product documentation before assuming that an integrated ANSI 25 element is available.

The same principle applies to UR, 8 Series, and distribution relay families.

Do not assume that all GE Multilin relays provide identical ANSI 25 functionality, voltage input arrangements, closing compensation, or live/dead supervision.

15. General GE Multilin Engineering Workflow

The following is a generic engineering procedure. Actual software functions, menu structures, and configuration methods depend on the model and firmware.

Step 1 – Identify the relay

Record:

  • Relay model.
  • Product order code.
  • Firmware version.
  • Available hardware.
  • Voltage input configuration.
  • Applicable software version.

Step 2 – Review the circuit-breaker arrangement

Identify:

  • Bus-side voltage source.
  • Line-side voltage source.
  • VT locations.
  • Breaker closing time.
  • Breaker control philosophy.
  • Required interlocking signals.

Step 3 – Define synchronism-check settings

Establish the approved values for:

  • Voltage difference.
  • Phase-angle difference.
  • Slip frequency.
  • Live/dead thresholds.
  • Voltage supervision.
  • Permissive timing.
  • Closing compensation, if available and required.

Step 4 – Configure signal logic

Typical signals include:

  • Synchronism-check request.
  • Synchronism-check permissive.
  • Bus voltage healthy.
  • Line voltage healthy.
  • Live-bus indication.
  • Dead-bus indication.
  • Live-line indication.
  • Dead-line indication.
  • VT failure.
  • External closing block.
  • Breaker close command.

Step 5 – Configure closing interlocking

Ensure that the circuit-breaker close command is permitted only when the applicable conditions are satisfied.

The closing logic may include:

  • Synchronism-check permissive.
  • Live/dead supervision.
  • Breaker readiness.
  • No active lockout.
  • No external block.
  • Valid voltage measurements.

Step 6 – Verify configuration

Check the settings, signal mapping, binary inputs, outputs, and control logic before downloading the configuration.

Where applicable, retain a backup of the original settings and document the approved revision.

16. Practical Synchronism-Check Calculation

Consider a 132 kV transmission line connected to a bus through a circuit breaker.

Assume the following measurements:

ParameterBus sideLine side
Voltage132 kV129 kV
Frequency50.00 Hz50.05 Hz
Phase angle4°13°

Assume the approved synchronism-check limits are:

  • Maximum voltage difference: 5%.
  • Maximum phase-angle difference: 15°.
  • Maximum slip frequency: 0.1 Hz.

16.1 Voltage difference

[
\Delta V=|132-129|=3\text{ kV}
]

[
\Delta V_{%}=\frac{3}{132}\times100
]

[
\Delta V_{%}=2.27%
]

The voltage-difference criterion is satisfied.

16.2 Phase-angle difference

[
\Delta\theta=|13-4|=9^\circ
]

The phase-angle criterion is satisfied.

16.3 Frequency difference

[
\Delta f=|50.05-50.00|
]

[
\Delta f=0.05\text{ Hz}
]

The slip-frequency criterion is satisfied.

16.4 Overall decision

All three illustrative criteria are satisfied.

However, the final closing permissive still depends on:

  • Valid voltage measurement.
  • Correct phase sequence.
  • Breaker readiness.
  • External interlocks.
  • Applicable closing logic.
  • Any required voltage supervision.

This example demonstrates the calculation method. It does not represent a recommended setting for every 132 kV system.

17. Synchronism-Check Testing and Commissioning

Testing must verify both the measurement function and the actual closing-permissive logic.

A relay may measure the voltage difference correctly but still fail to issue the correct permissive because of incorrect phase assignment, signal mapping, or external interlocking.

17.1 Pre-test checks

Before testing:

  • Confirm the approved synchronism-check settings.
  • Verify the relay model and firmware.
  • Check VT ratios and connections.
  • Confirm voltage input assignments.
  • Verify phase sequence.
  • Check voltage measurement scaling.
  • Confirm binary input and output assignments.
  • Review breaker closing logic.
  • Verify the test equipment connections.

17.2 Voltage-difference test

  1. Apply the same voltage magnitude to both sides.
  2. Confirm the voltage difference is approximately zero.
  3. Increase the voltage on one side.
  4. Monitor the measured difference.
  5. Test values below and above the configured limit.
  6. Confirm the expected permissive and blocking behavior.

17.3 Phase-angle test

  1. Apply suitable voltage signals to both sides.
  2. Set the phase-angle difference to zero.
  3. Confirm the synchronism-check status.
  4. Increase the angle difference gradually.
  5. Test the configured operating boundary.
  6. Verify that closing is blocked outside the permitted range.

17.4 Slip-frequency test

  1. Apply voltage signals with equal frequencies.
  2. Confirm zero or near-zero slip.
  3. Introduce a controlled frequency difference.
  4. Monitor the calculated slip frequency.
  5. Verify the configured threshold.
  6. Confirm that an excessive slip condition blocks closing.

17.5 Live/dead supervision test

Test the following conditions:

  • Live bus and dead line.
  • Dead bus and live line.
  • Live bus and live line.
  • Dead bus and dead line.

Verify the required permissive or blocking response for each condition.

17.6 VT failure test

Where voltage-failure supervision is implemented:

  1. Simulate the applicable VT failure condition.
  2. Verify the voltage supervision indication.
  3. Confirm that the scheme does not incorrectly interpret a measurement failure as a genuine dead condition.
  4. Verify the expected closing block or alternative logic.

17.7 Complete functional test

The final test should include:

  • Synchronism-check request.
  • Voltage comparison.
  • Phase-angle comparison.
  • Slip-frequency comparison.
  • Permissive output.
  • External interlocks.
  • Breaker close output.
  • Event and disturbance recording.

The circuit-breaker closing circuit should be tested under an approved test and safety procedure.

18. Common Synchronism-Check Problems

Problem 1 – Closing permissive is never issued

Possible causes:

  • Excessive voltage difference.
  • Excessive phase-angle difference.
  • Excessive slip frequency.
  • Incorrect VT ratio.
  • Incorrect phase assignment.
  • Active external block.
  • Invalid voltage measurement.

Recommended checks:

  • Monitor both voltage inputs.
  • Verify VT scaling.
  • Check phase sequence.
  • Review all permissive conditions.

Problem 2 – Incorrect phase-angle measurement

Possible causes:

  • Incorrect voltage wiring.
  • Incorrect phase assignment.
  • Different phase references.
  • Wrong VT polarity or connection.
  • Incorrect measurement configuration.

Recommended checks:

  • Verify the physical VT circuits.
  • Compare relay measurements with calibrated test equipment.
  • Confirm phase sequence and reference definitions.

Problem 3 – False dead-bus indication

Possible causes:

  • VT fuse failure.
  • Missing voltage input.
  • Incorrect voltage threshold.
  • Incorrect voltage scaling.
  • Wiring fault.

Recommended checks:

  • Inspect the VT secondary circuits.
  • Verify voltage input measurements.
  • Check voltage-failure supervision.
  • Confirm the dead-voltage threshold.

Problem 4 – Closing occurs outside the expected synchronism window

Possible causes:

  • Incorrect closing logic.
  • Bypassed synchronism-check interlock.
  • Incorrect permissive latching.
  • Incorrect signal mapping.
  • Unintended external close path.

Recommended checks:

  • Trace the complete close-command path.
  • Verify the actual output logic.
  • Review event records.
  • Test every permitted closing path.

Problem 5 – Synchronism check operates correctly during testing but not in service

Possible causes:

  • Incorrect field VT connections.
  • Different voltage reference points.
  • Wiring or polarity problems.
  • Incorrect control logic.
  • Intermittent voltage supervision.
  • Incorrect breaker status feedback.

Recommended checks:

  • Compare field measurements with relay values.
  • Verify the complete VT circuit.
  • Check the station control logic.
  • Review event records and time-stamped indications.

19. Synchronism-Check Commissioning Checklist

No.Inspection or testResult
1Confirm ANSI 25 availability☐
2Verify relay model and firmware☐
3Confirm bus-side VT connection☐
4Confirm line-side VT connection☐
5Verify VT ratios☐
6Verify phase sequence☐
7Verify voltage scaling☐
8Test voltage-difference measurement☐
9Test phase-angle measurement☐
10Test slip-frequency measurement☐
11Verify live/dead supervision☐
12Test VT failure supervision☐
13Verify breaker closing time data☐
14Check closing permissive logic☐
15Verify external interlocks☐
16Test breaker close output☐
17Verify event records☐
18Test autoreclosing integration☐
19Confirm final approved settings☐
20Save commissioning records☐

20. Best Engineering Practices

For reliable synchronism-check protection:

  1. Use voltage measurements from the correct sides of the circuit breaker.
  2. Verify VT ratios, phase sequence, and polarity.
  3. Define voltage, angle, and frequency limits through an engineering study.
  4. Consider breaker closing time when designing synchronization schemes.
  5. Distinguish synchronism-check supervision from automatic synchronizing.
  6. Implement suitable live/dead voltage supervision.
  7. Ensure VT failure does not create an unsafe closing permissive.
  8. Coordinate ANSI 25 with autoreclosing and breaker-control logic.
  9. Verify every closing path, including local, remote, and automatic commands.
  10. Test the complete scheme before returning the circuit to service.

21. Training on GE Multilin Protection Relays by Elec-Engg

Synchronism-check protection requires a practical understanding of voltage measurement, phasor relationships, breaker control, protection logic, and substation commissioning.

Elec-Engg provides practical technical training by Dr Saeed Roostaee (Electrical Engineering) for engineers working in power-system protection, relay configuration, commissioning, operation, and maintenance.

Relevant training subjects include:

  • GE Multilin protection relay families.
  • GE Multilin relay configuration using EnerVista.
  • Generator protection and synchronizing applications.
  • Synchronism-check protection (ANSI 25).
  • Autoreclosing protection (ANSI 79).
  • Distance protection (ANSI 21).
  • Breaker failure protection (ANSI 50BF).
  • CT and VT circuits and measurement verification.
  • Secondary injection and functional testing.
  • IEC 61850 communication and substation automation.

Training delivery options include:

  • Pre-recorded technical video courses.
  • Structured self-paced training.
  • Live online training.
  • Face-to-face technical training.
  • Customized in-house training for companies and utilities.

Visit Elec-Engg to explore available training programs or contact us to discuss a customized technical training requirement.

22. Frequently Asked Questions

What is ANSI 25 in a protection relay?

ANSI 25 identifies the synchronism-check function. It supervises circuit-breaker closing when two energized systems are being connected.

What parameters are checked by synchronism check?

Typical parameters include voltage magnitude difference, phase-angle difference, and frequency difference. Voltage validity and additional closing conditions may also be supervised.

What is the difference between synchronism check and synchronizing?

Synchronism check evaluates whether closing conditions are acceptable and provides a permissive. Automatic synchronizing actively adjusts generator voltage, frequency, and phase angle to achieve synchronization.

Why is slip frequency important?

Slip frequency determines how quickly the phase-angle difference changes between two systems. A high slip frequency can cause the systems to move outside the acceptable phase-angle window before the breaker contacts close.

Can synchronism check be used with autoreclosing?

Yes. It can supervise automatic reclosing when both sides of the breaker may be energized, provided that the required function and control logic are implemented.

Does every GE Multilin relay have ANSI 25?

No. Function availability and implementation depend on the exact relay model, firmware, hardware, and application.

What is live-bus/dead-line supervision?

It is a closing philosophy in which an energized bus may be connected to a de-energized line, subject to the configured voltage and interlocking conditions.

What happens if the VT circuit fails?

The scheme should detect or supervise invalid voltage measurements and prevent an unsafe closing decision. The exact response depends on the design.

Is synchronism check necessary for every circuit-breaker closing operation?

Not necessarily. Its application depends on the network arrangement, whether both sides may be energized, and the approved operating philosophy.

23. Related Articles

  • GE Multilin Protection Functions and ANSI Device Numbers.
  • GE Multilin Generator Protection: G60, G30 and 889.
  • GE Multilin Autoreclosing Protection (ANSI 79).
  • GE Multilin Distance Protection (ANSI 21).
  • GE Multilin Circuit Breaker Failure Protection (ANSI 50BF).
  • GE Multilin CT and VT Configuration.
  • GE Multilin Protection Relay Testing and Commissioning.
  • GE Multilin IEC 61850 Communication and Substation Automation.

Conclusion

Synchronism-check protection (ANSI 25) is essential wherever circuit breakers connect two potentially energized electrical systems. By supervising voltage difference, phase-angle difference, and slip frequency, it helps prevent unsuitable closing operations and reduces the risk of damaging electrical and mechanical transients.

Successful implementation depends on accurate VT measurements, correct phase references, appropriate settings, breaker closing-time considerations, and reliable integration with autoreclosing and substation control logic.

For GE Multilin applications, always verify the exact ANSI 25 functionality and configuration method against the relevant relay model and firmware documentation.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top